[Serial-pci-info] lspci -vv

SourceForge Headquarters 1320 Columbia Street Suite 310 San Diego, CA 92101 +1 (858) 422-6466

Dear Sourceforge,

Below is the output of lspci -vv on my system. The output that I receive
at startup is:

Startup error
-------------

PCI: Found IRQ 11 for device 02:0d.0
Redundant entry in serial pci_table.  Please send the output of
lspci -vv, this message (12b9,1008,12b9,baba)
and the manufacturer and name of serial board or modem board
to ser...@li....

Output of lspci -vv
-------------------

00:00.0 Host bridge: Intel Corp. 82815 815 Chipset Host Bridge and
Memory Controller Hub (rev 02)
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ >SERR- <PERR-
	Latency: 0
	Region 0: Memory at f8000000 (32-bit, prefetchable) [size=64M]
	Capabilities: [88] #09 [f104]
	Capabilities: [a0] AGP version 2.0
		Status: RQ=31 SBA+ 64bit- FW- Rate=x1,x2,x4
		Command: RQ=0 SBA- AGP+ 64bit- FW- Rate=x4

00:01.0 PCI bridge: Intel Corp. 82815 815 Chipset AGP Bridge (rev 02)
(prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
	Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
	Latency: 64
	Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
	Memory behind bridge: fc900000-fe9fffff
	Prefetchable memory behind bridge: f0600000-f46fffff
	BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-

00:1e.0 PCI bridge: Intel Corp. 82801BA/CA PCI Bridge (rev 01) (prog-if
00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
	Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
	Latency: 0
	Bus: primary=00, secondary=02, subordinate=02, sec-latency=64
	I/O behind bridge: 0000d000-0000dfff
	Memory behind bridge: fea00000-feafffff
	Prefetchable memory behind bridge: f4700000-f47fffff
	BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-

00:1f.0 ISA bridge: Intel Corp. 82801BA ISA Bridge (LPC) (rev 01)
	Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
	Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
	Latency: 0

00:1f.1 IDE interface: Intel Corp. 82801BA IDE U100 (rev 01) (prog-if 80
[Master])
	Subsystem: Intel Corp.: Unknown device 4541
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
	Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
	Latency: 0
	Region 4: I/O ports at ffa0 [size=16]

00:1f.2 USB Controller: Intel Corp. 82801BA/BAM USB (Hub #1) (rev 01)
(prog-if 00 [UHCI])
	Subsystem: Intel Corp.: Unknown device 4541
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
	Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
	Latency: 0
	Interrupt: pin D routed to IRQ 10
	Region 4: I/O ports at ef80 [size=32]

00:1f.3 SMBus: Intel Corp. 82801BA/BAM SMBus (rev 01)
	Subsystem: Intel Corp.: Unknown device 4541
	Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
	Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
	Interrupt: pin B routed to IRQ 9
	Region 4: I/O ports at efa0 [size=16]

01:00.0 VGA compatible controller: nVidia Corporation NV6 [Vanta] (rev
15) (prog-if 00 [VGA])
	Subsystem: nVidia Corporation: Unknown device 0001
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
	Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
	Latency: 248 (1250ns min, 250ns max)
	Interrupt: pin A routed to IRQ 11
	Region 0: Memory at fd000000 (32-bit, non-prefetchable) [size=16M]
	Region 1: Memory at f2000000 (32-bit, prefetchable) [size=32M]
	Expansion ROM at fe9f0000 [disabled] [size=64K]
	Capabilities: [60] Power Management version 1
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [44] AGP version 2.0
		Status: RQ=31 SBA- 64bit- FW- Rate=x1,x2,x4
		Command: RQ=31 SBA- AGP+ 64bit- FW- Rate=x4

02:0b.0 Ethernet controller: Standard Microsystems Corp [SMC] 83C170QF
(rev 08)
	Subsystem: Standard Microsystems Corp [SMC] EtherPower II 10/100
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
	Latency: 64 (2000ns min, 7000ns max)
	Interrupt: pin A routed to IRQ 3
	Region 0: I/O ports at d800 [size=256]
	Region 1: Memory at feaff000 (32-bit, non-prefetchable) [size=4K]
	Expansion ROM at feae0000 [disabled] [size=64K]
	Capabilities: [dc] Power Management version 1
		Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA
PME(D0-,D1+,D2+,D3hot+,D3cold+)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

02:0c.0 Multimedia audio controller: Creative Labs SB Live! EMU10k1 (rev
07)
	Subsystem: Creative Labs CT4780 SBLive! Value
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
	Latency: 64 (500ns min, 5000ns max)
	Interrupt: pin A routed to IRQ 9
	Region 0: I/O ports at df80 [size=32]
	Capabilities: [dc] Power Management version 1
		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

02:0c.1 Input device controller: Creative Labs SB Live! MIDI/Game Port
(rev 07)
	Subsystem: Creative Labs Gameport Joystick
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
	Latency: 64
	Region 0: I/O ports at dff0 [size=8]
	Capabilities: [dc] Power Management version 1
		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

02:0d.0 Serial controller: US Robotics/3Com 56K FaxModem Model 5610 (rev
01) (prog-if 02 [16550])
	Subsystem: US Robotics/3Com: Unknown device baba
	Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
	Interrupt: pin A routed to IRQ 11
	Region 0: I/O ports at dfe0 [size=8]
	Capabilities: [dc] Power Management version 2
		Flags: PMEClk- DSI- D1- D2+ AuxCurrent=0mA
PME(D0+,D1-,D2+,D3hot+,D3cold+)
		Status: D0 PME-Enable- DSel=0 DScale=2 PME-

If you require any additional information, I can be reached at the
contact information listed below.

Thanks for your help.

-------------------------------
David Merritt
3A Computer Science
University of Waterloo
dw2...@uw...