Menu
▾
▴
Re: [Plplot-general] Problems with plPlot VS 2017 build
|
From: David B. <stu...@gm...> - 2019-08-28 01:59:10
|
Phil, You have been very helpful in the past and I thank you. I was just now trying to build again to get the error and the rebuild rebuild went better. There were no cmake errors last time, but the sln barked that not all projects were loaded and terminated with an error. I deleted the old build and tried again. this time a great many more files and folders appeared in the build dir and the sln opened w/o any warnings or errors. However, now it is hanging in the INSTALL phase. Here is the last few lines in the IDE output window: 9>------ Build started: Project: parity_bit_check, Configuration: Debug x64 ------ 9>Building Custom Rule C:/plplot-5.15.0/utils/CMakeLists.txt 9>CMake does not need to re-run because C:/plplot-5.15.0/build/utils/CMakeFiles/generate.stamp is up-to-date. 9>parity_bit_check.c 9>parity_bit_check.vcxproj -> C:\plplot-5.15.0\build\utils\Debug\parity_bit_check.exe 6>Building Custom Rule C:/plplot-5.15.0/include/CMakeLists.txt 6>CMake does not need to re-run because C:/plplot-5.15.0/build/include/CMakeFiles/generate.stamp is up-to-date. Not sure how long the install should take. David On 8/27/2019 8:05 PM, Phil Rosenberg wrote: > Hi David > Any chance you could report the exact cmake command you are using and > the exact error message you are getting? > > I also use plplot with wxwidgets and VS, so I'll see if I can help as > best as I can. > > Phil > > Get Outlook for Android <https://aka.ms/ghei36> > > ------------------------------------------------------------------------ > *From:* David Bergman <stu...@gm...> > *Sent:* Wednesday, August 28, 2019 12:27:21 AM > *To:* plp...@li... > <plp...@li...> > *Subject:* [Plplot-general] Problems with plPlot VS 2017 build > All, > > I had a drive fail recently, data is all backed up, but I am now > installing s/w and getting newer versions of wxWidgets and plPlot. > Unfortunately, following the plPlot instructions to the best of my > ability did not lead to success. > > The cmake seemed to work without a hitch, but would not install in my > build directory. I moved files into build and opened and ran the sln > from there. The sln reported 2 successful and 1 failed at the end of > the build. I see no dll or lib anywhere. > > I had similar issues with my first plplot install a couple years ago and > was able to get help from this forum and hope that I can again. > > I have Windows 8.1, wxWidgets-3.1.2, MS VS 2017 and am trying to build > plplot-5.15.0. > > Since my last request for help I have been developing quite a bit of > simulation software that is controlled by the wxWidgets GUI and displays > results using plplot. If you could please confirm that code written > will work once the new install is complete I would greatly appreciate > it. I of course expect to have to change paths to include directories > and point to new dll as needed but are there are major changes to plplot > functions, interfaces, or expected behavior? > > Thank you in advance for your help. > > David > > -- > David Bergman > David R Bergman Music LLC > "Have Guitar Will Travel" > Morristown NJ > 551-655-4720 > stu...@gm... > www.davidrobertbergmanmusic.com <http://www.davidrobertbergmanmusic.com> > > > --- > This email has been checked for viruses by Avast antivirus software. > https://www.avast.com/antivirus > > > > _______________________________________________ > Plplot-general mailing list > Plp...@li... > https://lists.sourceforge.net/lists/listinfo/plplot-general -- David Bergman David R Bergman Music LLC "Have Guitar Will Travel" Morristown NJ 551-655-4720 stu...@gm... www.davidrobertbergmanmusic.com |
