Version 0.11.5 ( OP and OPGUI) was released today.
Changes:
fixed config word write on some 33FJXX devices
If you would like to refer to this comment somewhere else in this project, copy and paste the following link:
Anonymous
Anonymous
-
2021-12-14
thx
If you would like to refer to this comment somewhere else in this project, copy and paste the following link:
Anonymous
Anonymous
-
2022-01-16
Hi, First of all, thank you and Happy new Year in 2022
there is a problem in opgui.exe v0.11.5 . I can not get 16LF1554 in list to program . there is a gap from F1527 to F1574. I set like F1503 and write ok ( the program recognise that in programmer is inserted a LF1554. After that I looked up , and get the 16LF1554 in opgui. exe V0.9.1 that works properly.
The second problem what I have is that I compiled a program with Micro C Pro for PIC v7.6 on 16F18854 in which I also used the EEPROM editor.
it looks like .Hex contains EEPROM values but in opgui v0.11.5 they are not seen and the EEPROM area is not written. I don't know where the mistake is. The basic program is written ok and works.
I atas the hex, (onli the first 3 adres I used)
Apparently the type filter is not working correctly. If you switch to all devices (*) you should be able to select your device.
If you would like to refer to this comment somewhere else in this project, copy and paste the following link:
Anonymous
Anonymous
-
2022-02-02
Hi , im sorry writing here , but i didnt found any help in other topics and didnt wanted to start a new one, I just built this nice programmer, and it worked at the first try, but im stucked with a DS2430A one wire Eeprom, I am able to write the memory, but there is a one time writeable Application register , how can i write that part of the chip? I have brand new chips with empty application register but i donno how to acces that part of memory with opgui 0.11.5
Thank you.
If you would like to refer to this comment somewhere else in this project, copy and paste the following link:
Version 0.11.5 ( OP and OPGUI) was released today.
Changes:
fixed config word write on some 33FJXX devices
thx
Hi, First of all, thank you and Happy new Year in 2022
there is a problem in opgui.exe v0.11.5 . I can not get 16LF1554 in list to program . there is a gap from F1527 to F1574. I set like F1503 and write ok ( the program recognise that in programmer is inserted a LF1554. After that I looked up , and get the 16LF1554 in opgui. exe V0.9.1 that works properly.
The second problem what I have is that I compiled a program with Micro C Pro for PIC v7.6 on 16F18854 in which I also used the EEPROM editor.
it looks like .Hex contains EEPROM values but in opgui v0.11.5 they are not seen and the EEPROM area is not written. I don't know where the mistake is. The basic program is written ok and works.
I atas the hex, (onli the first 3 adres I used)
hi. If you need additional information, I can be at your disposal.I was in the previous post but I was not logged in. With best regards Stefan
Apparently the type filter is not working correctly. If you switch to all devices (*) you should be able to select your device.
Hi , im sorry writing here , but i didnt found any help in other topics and didnt wanted to start a new one, I just built this nice programmer, and it worked at the first try, but im stucked with a DS2430A one wire Eeprom, I am able to write the memory, but there is a one time writeable Application register , how can i write that part of the chip? I have brand new chips with empty application register but i donno how to acces that part of memory with opgui 0.11.5
Thank you.
Hi, this is potentially useful, so can you start a new topic?
Sure :)