This is an automated email from the git hooks/post-receive script. It was
generated because a ref change was pushed to the repository containing
the project "Main OpenOCD repository".
The branch, master has been updated
via 15d90dd21cfc480714fbefa238998e6b00b9c4b1 (commit)
from 66faa420a468d5961a0799785042e130cb7441f8 (commit)
Those revisions listed above that are new to this repository have
not appeared on any other notification email; so we list those
revisions in full, below.
- Log -----------------------------------------------------------------
commit 15d90dd21cfc480714fbefa238998e6b00b9c4b1
Author: Marc Schink <de...@za...>
Date: Fri Dec 13 07:34:03 2024 +0000
tcl/target: Add config for STM32U0x
Tested with NUCLEO-U083RC development board.
Change-Id: Iec668b45166543adcd1fa5077d41c57a35d3becf
Signed-off-by: Marc Schink <de...@za...>
Reviewed-on: https://review.openocd.org/c/openocd/+/8648
Tested-by: jenkins
Reviewed-by: Tomas Vanek <va...@fb...>
diff --git a/tcl/target/stm32u0x.cfg b/tcl/target/stm32u0x.cfg
new file mode 100644
index 000000000..d3aaed3cb
--- /dev/null
+++ b/tcl/target/stm32u0x.cfg
@@ -0,0 +1,55 @@
+# SPDX-License-Identifier: GPL-2.0-or-later
+
+# Configuration file for STM32U0x series.
+#
+# STM32U0 devices support only SWD transport.
+#
+
+source [find mem_helper.tcl]
+
+if { [info exists CHIPNAME] } {
+ set _CHIPNAME $CHIPNAME
+} else {
+ set _CHIPNAME stm32u0x
+}
+
+# Work-area is a space in RAM used for flash programming, by default use 4 KiB.
+if { [info exists WORKAREASIZE] } {
+ set _WORKAREASIZE $WORKAREASIZE
+} else {
+ set _WORKAREASIZE 0x1000
+}
+
+if { [info exists CPUTAPID] } {
+ set _CPUTAPID $CPUTAPID
+} else {
+ set _CPUTAPID 0x6ba02477
+}
+
+swd newdap $_CHIPNAME cpu -expected-id $_CPUTAPID
+dap create $_CHIPNAME.dap -chain-position $_CHIPNAME.cpu
+
+set _TARGETNAME $_CHIPNAME.cpu
+target create $_TARGETNAME cortex_m -endian little -dap $_CHIPNAME.dap
+
+$_TARGETNAME configure -work-area-phys 0x20000000 -work-area-size $_WORKAREASIZE -work-area-backup 0
+
+flash bank $_CHIPNAME.flash stm32l4x 0x08000000 0 0 0 $_TARGETNAME
+flash bank $_CHIPNAME.otp stm32l4x 0x1FFF6800 0 0 0 $_TARGETNAME
+
+adapter speed 2000
+
+if {![using_hla]} {
+ # Use SYSRESETREQ to perform a soft reset if SRST is not fitted.
+ cortex_m reset_config sysresetreq
+}
+
+$_TARGETNAME configure -event examine-end {
+ # Enable debug during low power modes (uses more power).
+ # DBGMCU_CR |= DBG_STANDBY | DBG_STOP
+ mmw 0x40015804 0x00000006 0
+
+ # Stop watchdog counters when core is halted.
+ # DBGMCU_APB1_FZR |= DBG_IWDG_STOP | DBG_WWDG_STOP
+ mmw 0x40015808 0x00001800 0
+}
-----------------------------------------------------------------------
Summary of changes:
tcl/target/stm32u0x.cfg | 55 +++++++++++++++++++++++++++++++++++++++++++++++++
1 file changed, 55 insertions(+)
create mode 100644 tcl/target/stm32u0x.cfg
hooks/post-receive
--
Main OpenOCD repository
|
