[Openocd-svn] r2269 - trunk/tcl/target

[<oh...@ma...>]

Author: oharboe
Date: 2009-06-17 22:49:55 +0200 (Wed, 17 Jun 2009)
New Revision: 2269

Modified:
   trunk/tcl/target/lpc2478.cfg
Log:
Freddie Chopin <fre...@op...> makes lpc2478.cfg file more "standard" and - what is most important - correct (it's working [; ). I've also added some comments which try to clarify the meaning of all that's in there.

Modified: trunk/tcl/target/lpc2478.cfg
===================================================================
--- trunk/tcl/target/lpc2478.cfg	2009-06-17 10:51:34 UTC (rev 2268)
+++ trunk/tcl/target/lpc2478.cfg	2009-06-17 20:49:55 UTC (rev 2269)
@@ -1,35 +1,49 @@
-# Testing feeedback wanted!
-set _CHIPNAME lpc2478
-set _ENDIAN little
-set _CPUTAPID 0x4f1f0f0f
+# NXP LPC2478 ARM7TDMI-S with 512kB Flash and 64kB Local On-Chip SRAM (98kB total), clocked with 4MHz internal RC oscillator
 
-# Use RCLK. If RCLK is not available fall back to 500kHz. 
-# 
-# Depending on cabling you might be able to eek this up to 2000kHz.
-jtag_rclk 500
+if { [info exists CHIPNAME] } {
+	set  _CHIPNAME $CHIPNAME
+} else {
+	set  _CHIPNAME lpc2478
+}
 
-jtag_nsrst_delay 200
-jtag_ntrst_delay 200
+if { [info exists ENDIAN] } {
+	set  _ENDIAN $ENDIAN
+} else {
+	set  _ENDIAN little
+}
 
-#use combined on interfaces or targets that can't set TRST/SRST separately
+if { [info exists CPUTAPID ] } {
+	set _CPUTAPID $CPUTAPID
+} else {
+	set _CPUTAPID 0x4f1f0f0f
+}
+
+#delays on reset lines
+jtag_nsrst_delay 100
+jtag_ntrst_delay 100
+
+# LPC2000 -> SRST causes TRST
 reset_config trst_and_srst srst_pulls_trst
 
-
 jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
 
 set _TARGETNAME [format "%s.cpu" $_CHIPNAME]
 target create $_TARGETNAME arm7tdmi -endian $_ENDIAN -chain-position $_TARGETNAME -variant arm7tdmi-s_r4
-$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x40000000 -work-area-size 0x4000 -work-area-backup 0
 
+# LPC2478 has 64kB of SRAM on its main system bus (so-called Local On-Chip SRAM)
+$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x40000000 -work-area-size 0x10000 -work-area-backup 0
 
 $_TARGETNAME configure -event reset-init {
 	# Force target into ARM state
 	soft_reset_halt
-	# FIX!!!! should we remap the range below??? Is this applicable to
-	# Copied from LPC2148.
-	#do not remap 0x0000-0x0020 to anything but the flash
+	# Do not remap 0x0000-0x0020 to anything but the Flash
 	mwb 0xE01FC040 0x01
 }
 
+# LPC2378 has 512kB of FLASH, but upper 8kB are occupied by bootloader.
+# After reset the chip uses its internal 4MHz RC oscillator.
+# flash bank lpc2000 <base> <size> 0 0 <target#> <variant> <clock> [calc checksum]
+flash bank lpc2000 0x0 0x7D000 0 0 0 lpc2000_v2 12000 calc_checksum
 
-flash bank lpc2000 0x0 0x7D000 0 0 0 lpc2000_v2 12000 calc_checksum
+# Try to use RCLK, if RCLK is not available use "normal" mode. 4MHz / 6 = 666kHz, so use 500.
+jtag_rclk 500