[Openocd-svn] r1634 - trunk/src/target/target

[oharboe at B. <oh...@ma...>]

Author: oharboe
Date: 2009-05-07 11:57:13 +0200 (Thu, 07 May 2009)
New Revision: 1634

Modified:
   trunk/src/target/target/ti_dm355.cfg
Log:
fix line endings

Modified: trunk/src/target/target/ti_dm355.cfg
===================================================================
--- trunk/src/target/target/ti_dm355.cfg	2009-05-07 08:19:07 UTC (rev 1633)
+++ trunk/src/target/target/ti_dm355.cfg	2009-05-07 09:57:13 UTC (rev 1634)
@@ -1,63 +1,63 @@
-#
-# Texas Instruments DaVinci family:  TMS320DM355
-#
-if { [info exists CHIPNAME] } {
-   set  _CHIPNAME $CHIPNAME
-} else {
-   set  _CHIPNAME dm355
-}
-if { [info exists ENDIAN] } {
-   set  _ENDIAN $ENDIAN
-} else {
-   set  _ENDIAN little
-}
-
-#
-# For now, expect EMU0/EMU1 jumpered LOW (not TI's default) so ARM and ETB
-# are enabled without making ICEpick route ARM and ETB into the JTAG chain.
-#
-# Also note:  when running without RTCK before the PLLs are set up, you
-# may need to slow the JTAG clock down quite a lot (under 2 MHz).
-#
-
-# Subsidiary TAP: ARM ETB11, with scan chain for 4K of ETM trace buffer
-if { [info exists ETB_TAPID ] } {
-   set _ETB_TAPID $ETB_TAPID
-} else {
-   set _ETB_TAPID 0x2b900f0f
-}
-jtag newtap $_CHIPNAME etb -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_ETB_TAPID
-
-# Subsidiary TAP: ARM926ejs with scan chains for ARM Debug, EmbeddedICE-RT, ETM.
-if { [info exists CPU_TAPID ] } {
-   set _CPU_TAPID $CPU_TAPID
-} else {
-   set _CPU_TAPID 0x07926001
-}
-jtag newtap $_CHIPNAME arm -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPU_TAPID
-
-# Primary TAP: ICEpick (JTAG route controller) and boundary scan
-if { [info exists JRC_TAPID ] } {
-   set _JRC_TAPID $JRC_TAPID
-} else {
-   set _JRC_TAPID 0x0b73b02f
-}
-jtag newtap $_CHIPNAME jrc -irlen 6 -ircapture 0x1 -irmask 0x3f -expected-id $_JRC_TAPID
-
-# GDB target:  the ARM, using SRAM1 for scratch.  SRAM0 (also 16K)
-# and the ETB memory (4K) are other options, while trace is unused.
-set _TARGETNAME $_CHIPNAME.arm
-
-target create $_TARGETNAME arm926ejs -endian $_ENDIAN -chain-position $_TARGETNAME
-$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x00014000 -work-area-size 0x4000 -work-area-backup 0
-
-arm7_9 dbgrq enable
-arm7_9 fast_memory_access enable
-arm7_9 dcc_downloads enable
-
-# trace setup
-# FIXME we ought to be able to say "... config $_TARGETNAME ..."
-# (not "config 0") facilitating additional targets (e.g. other chips)
-etm config 0 16 normal full etb
-etb config 0 $_CHIPNAME.etb
-
+#
+# Texas Instruments DaVinci family:  TMS320DM355
+#
+if { [info exists CHIPNAME] } {
+   set  _CHIPNAME $CHIPNAME
+} else {
+   set  _CHIPNAME dm355
+}
+if { [info exists ENDIAN] } {
+   set  _ENDIAN $ENDIAN
+} else {
+   set  _ENDIAN little
+}
+
+#
+# For now, expect EMU0/EMU1 jumpered LOW (not TI's default) so ARM and ETB
+# are enabled without making ICEpick route ARM and ETB into the JTAG chain.
+#
+# Also note:  when running without RTCK before the PLLs are set up, you
+# may need to slow the JTAG clock down quite a lot (under 2 MHz).
+#
+
+# Subsidiary TAP: ARM ETB11, with scan chain for 4K of ETM trace buffer
+if { [info exists ETB_TAPID ] } {
+   set _ETB_TAPID $ETB_TAPID
+} else {
+   set _ETB_TAPID 0x2b900f0f
+}
+jtag newtap $_CHIPNAME etb -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_ETB_TAPID
+
+# Subsidiary TAP: ARM926ejs with scan chains for ARM Debug, EmbeddedICE-RT, ETM.
+if { [info exists CPU_TAPID ] } {
+   set _CPU_TAPID $CPU_TAPID
+} else {
+   set _CPU_TAPID 0x07926001
+}
+jtag newtap $_CHIPNAME arm -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPU_TAPID
+
+# Primary TAP: ICEpick (JTAG route controller) and boundary scan
+if { [info exists JRC_TAPID ] } {
+   set _JRC_TAPID $JRC_TAPID
+} else {
+   set _JRC_TAPID 0x0b73b02f
+}
+jtag newtap $_CHIPNAME jrc -irlen 6 -ircapture 0x1 -irmask 0x3f -expected-id $_JRC_TAPID
+
+# GDB target:  the ARM, using SRAM1 for scratch.  SRAM0 (also 16K)
+# and the ETB memory (4K) are other options, while trace is unused.
+set _TARGETNAME $_CHIPNAME.arm
+
+target create $_TARGETNAME arm926ejs -endian $_ENDIAN -chain-position $_TARGETNAME
+$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x00014000 -work-area-size 0x4000 -work-area-backup 0
+
+arm7_9 dbgrq enable
+arm7_9 fast_memory_access enable
+arm7_9 dcc_downloads enable
+
+# trace setup
+# FIXME we ought to be able to say "... config $_TARGETNAME ..."
+# (not "config 0") facilitating additional targets (e.g. other chips)
+etm config 0 16 normal full etb
+etb config 0 $_CHIPNAME.etb
+


Property changes on: trunk/src/target/target/ti_dm355.cfg
___________________________________________________________________
Name: svn:eol-style
   + native