Menu
▾
▴
Re: [Openbts-discuss] (no subject)
|
From: Anuja K. <anu...@gm...> - 2016-05-23 12:44:07
|
Hello, My cellphones are registering to network successfully,now I am able to make test sms,Direct sms, and two party sms. but during making test call or echo call asterisk CLI is showing following Notice [May 23 17:57:23] NOTICE[3069][C-00000000]: chan_sip.c:25450 handle_request_invite: Call from '' (127.0.0.1:5062) to extension '2600' rejected because extension not found in context 'default'. [May 23 17:57:59] WARNING[3069]: chan_sip.c:4175 retrans_pkt: Retransmission timeout reached on transmission 1247805829@127.0.0.1 for seqno 204 (Critical Response) -- See https://wiki.asterisk.org/wiki/display/AST/SIP+Retransmissions Packet timed out after 31999ms with no response I am unable to make calls,Please help me regarding the same. Best Regards Anuja On Tue, May 17, 2016 at 5:02 PM, Anuja Kokil <anu...@gm...> wrote: > Hi > > Actually, after getting IMSI successfully, i reconfigured LUR with .* , > and immediately my cell phone get connected to the network. i tried Direct > SMS and Echo SMS, it was successful attempt, Thank you so much for your > immediate response, It helped me lot today. > > Now trying to make test call to 2602 ,but it is immediately rejecting call > connection, > > in Asterisk terminal i am getting > > > [May 17 16:32:09] NOTICE[31257][C-0000000c]: chan_sip.c:25450 > handle_request_invite: Call from '' (127.0.0.1:5062) to extension '2602' > rejected because extension not found in context 'default'. > [May 17 16:32:27] WARNING[31257]: chan_sip.c:4175 retrans_pkt: > Retransmission timeout reached on transmission 1105886678@127.0.0.1 for > seqno 397 (Critical Response) -- See > https://wiki.asterisk.org/wiki/display/AST/SIP+Retransmissions > Packet timed out after 31998ms with no response > == Using SIP RTP CoS mark 5 > > Thankyou > Anuja > > On Tue, May 17, 2016 at 1:41 PM, Anuja Kokil <anu...@gm...> wrote: > >> I am using Log Periodic antenna (850-6500MHz) >> ,is it the issue that my phone is not connecting? >> >> Thanks >> Anuja >> >> On Tue, May 17, 2016 at 1:39 PM, Anuja Kokil <anu...@gm...> >> wrote: >> >>> Hello Alex, >>> >>> Thank you so much for your reply!! I am able to see IMSI in TMSI table >>> now! but still my phone is not connecting to network. >>> >>> I tried installing OsmoTRX using following commands >>> >>> $ git clone git://git.osmocom.org/osmo-trx >>> >>> $ autoreconf -i >>> >>> $ ./configure >>> $ make >>> $ sudo make install >>> $ osmo-trx -f >>> >>> after last command my transceiver enables >>> >>> In OpenBTS CLI it gives >>> OpenBTS> noise >>> noise RSSI is --2147483648 dB wrt full scale >>> MS RSSI target is -50 dB wrt full scale >>> >>> OpenBTS> version >>> release TRUNK+GPRS P built May 16 2016 rev8925M >>> >>> OpenBTS> power >>> current downlink power -1 dB wrt full scale >>> current attenuation bounds 0 to 10 dB >>> >>> OpenBTS> tmsis >>> TMSI IMSI age used >>> 1 001010000000003 6m 6m >>> >>> but in OsmoTRX terminal i am getting >>> WARNING 3032677184 13:31:00.0 Transceiver.cpp:674:pullRadioVector: >>> Clipping detected on received RACH or Normal Burst >>> WARNING 3032677184 13:31:00.0 Transceiver.cpp:674:pullRadioVector: >>> Clipping detected on received RACH or Normal Burst >>> >>> and still my phone is not registering to network >>> It is showing same message! >>> >>> Thanks & Regards >>> Anuja >>> >>> >>> >>> >>> >>> On Tue, May 17, 2016 at 11:42 AM, Anuja Kokil <anu...@gm...> >>> wrote: >>> >>>> Hello, >>>> >>>> I am new to this technology, I am working on B200 USRP and following >>>> the document "Getting Started with OpenBTS".I have reached up to Network >>>> creation. My mobile is showing network 'Test PLMN 1-1' .I have two SIM >>>> cards with MCC-001 and MNC-01. I am using Sony Xperia M mobile phone. My >>>> laptop is HP PC with intel core i5. >>>> >>>> The problem is, when i try to register to the network with my phone, it >>>> is not connecting and displaying the message "can't connect now,try again >>>> later", >>>> >>>> when i give the command tmsis- then it is showing empty TMSI table. >>>> >>>> I have configured Control.LUR.OpenRegistration to .* ,but still phone >>>> not registering to network. >>>> >>>> I am really not getting what is the problem,whether B200 is not >>>> compatible with OpenBTS? I read about external 10 MHz reference,is it >>>> necessity? if yes then i am not getting how to connect external reference >>>> with it? >>>> Is any Daughter Board required to connect with B200? >>>> Which USRP is better for Openbts N200 or B200? >>>> >>>> Please help me regarding the same. >>>> >>>> Thanks & Regards >>>> Anuja >>>> >>>> >>>> ------------------------------------------------------------------------------ >>>> Mobile security can be enabling, not merely restricting. Employees who >>>> bring their own devices (BYOD) to work are irked by the imposition of >>>> MDM >>>> restrictions. Mobile Device Manager Plus allows you to control only the >>>> apps on BYO-devices by containerizing them, leaving personal data >>>> untouched! >>>> https://ad.doubleclick.net/ddm/clk/304595813;131938128;j >>>> _______________________________________________ >>>> Openbts-discuss mailing list >>>> Ope...@li... >>>> https://lists.sourceforge.net/lists/listinfo/openbts-discuss >>>> >>>> >>> >> > |
