Menu
▾
▴
openautomation-svn
|
From: <ma...@us...> - 2010-11-11 17:37:19
|
Revision: 110
http://openautomation.svn.sourceforge.net/openautomation/?rev=110&view=rev
Author: makki1
Date: 2010-11-11 17:37:13 +0000 (Thu, 11 Nov 2010)
Log Message:
-----------
filled in some 1-wire devices to owfs/sensors.ini
Modified Paths:
--------------
PyWireGate/trunk/owfs_connector/sensors.ini
Modified: PyWireGate/trunk/owfs_connector/sensors.ini
===================================================================
--- PyWireGate/trunk/owfs_connector/sensors.ini 2010-11-11 15:56:02 UTC (rev 109)
+++ PyWireGate/trunk/owfs_connector/sensors.ini 2010-11-11 17:37:13 UTC (rev 110)
@@ -1,14 +1,70 @@
[DS1420]
+# ROM id-chip
+interfaces = present
-
[DS18B20]
+# Temperature with resolution, family 28
cycle = 15
interfaces = temperature,power
config_temperature_resolution = 10
config_temperature_sendcycle = 60
config_temperature_sendcycleoption = average
+[DS18S20]
+# Temperature with fixed resolution, family 10
+cycle = 15
+interfaces = temperature,power
+config_temperature_sendcycle = 60
+config_temperature_sendcycleoption = average
+[DS1990]
+# ROM iButtons, family 01
+cycle = 1
+interfaces = present
+# save parent busmaster-id/serial in DS to distinguish presence on different busmasters
+config_present_busmaster = true
+
[DS2438]
+# Battery-monitor with Vxx and current, family 26
+# /pages/page.3 conatins type: 0x19 or 0xF1 = TH, 0xF2 = THS
+# FIXME: several more (not widely used) to be added
cycle = 60
-interfaces = temperature,humidity,vis,VDD
+interfaces = temperature,HIH4000/humidity,vis,VAD,VDD
+
+[DS2406]
+# dual switch / IO, family 12
+# PIO.[A|B] if used as output
+# sensed.[A|B] if used as input
+# latch contains changed pin if alarming, must be reset after read
+# owread /uncached/$key/latch.ALL; owwrite /$key/latch.BYTE 0; owwrite /$key/set_alarm 311
+# latch returns CSV 0,1 if B changed
+cycle = 1
+interfaces = PIO.A,PIO.B,sensed.A,sensed.B,latch.ALL,latch.BYTE,set_alarm
+
+[DS2408]
+# 8x switch / IO, family 29
+# PIO.[0-7] if used as output
+# FIXME: sensed.[0-7] if used as input / latch not supported yet
+cycle = 1
+interfaces = PIO.0,PIO.1,PIO.2,PIO.3,PIO.4,PIO.5,PIO.6,PIO.7
+
+[DS2423]
+# Dual-counter, family 1D
+interfaces = counters.A,counters.B
+
+[DS2760]
+# battery-monitor, family 30
+# used for soil-moisture
+cycle = 60
+interfaces = temperature,current
+# values need to be calibrated for each sensor
+config_current_low = 0.14
+config_current_high = 0.14
+
+[DS9490]
+# USB-Busmaster, family 81
+# no interfaces but bus-specific statistics
+# /interface/statistics/errors
+# /interface/statistics/search_errors/error_pass_1
+# etc.
+
This was sent by the SourceForge.net collaborative development platform, the world's largest Open Source development site.
|
|
From: <ni...@us...> - 2010-11-22 18:39:12
|
Revision: 152
http://openautomation.svn.sourceforge.net/openautomation/?rev=152&view=rev
Author: nilss1
Date: 2010-11-22 18:39:06 +0000 (Mon, 22 Nov 2010)
Log Message:
-----------
ibutton 2401
Modified Paths:
--------------
PyWireGate/trunk/owfs_connector/sensors.ini
Modified: PyWireGate/trunk/owfs_connector/sensors.ini
===================================================================
--- PyWireGate/trunk/owfs_connector/sensors.ini 2010-11-22 14:59:41 UTC (rev 151)
+++ PyWireGate/trunk/owfs_connector/sensors.ini 2010-11-22 18:39:06 UTC (rev 152)
@@ -17,12 +17,10 @@
config_temperature_sendcycle = 60
config_temperature_sendcycleoption = average
-[DS1990]
+[DS2401]
# ROM iButtons, family 01
cycle = 1
interfaces = present
-# save parent busmaster-id/serial in DS to distinguish presence on different busmasters
-config_present_busmaster = true
[DS2438]
# Battery-monitor with Vxx and current, family 26
@@ -75,4 +73,3 @@
# /interface/statistics/errors
# /interface/statistics/search_errors/error_pass_1
# etc.
-
This was sent by the SourceForge.net collaborative development platform, the world's largest Open Source development site.
|
|
From: <ma...@us...> - 2010-11-29 20:56:13
|
Revision: 176
http://openautomation.svn.sourceforge.net/openautomation/?rev=176&view=rev
Author: makki1
Date: 2010-11-29 20:56:06 +0000 (Mon, 29 Nov 2010)
Log Message:
-----------
Add BAE to owsensors
Modified Paths:
--------------
PyWireGate/trunk/owfs_connector/sensors.ini
Modified: PyWireGate/trunk/owfs_connector/sensors.ini
===================================================================
--- PyWireGate/trunk/owfs_connector/sensors.ini 2010-11-29 20:46:42 UTC (rev 175)
+++ PyWireGate/trunk/owfs_connector/sensors.ini 2010-11-29 20:56:06 UTC (rev 176)
@@ -73,3 +73,19 @@
# /interface/statistics/errors
# /interface/statistics/search_errors/error_pass_1
# etc.
+
+[BAE]
+# BAE09x, family FC
+# chip_type 1 = 0910, 2 = 0911
+# path /910 contains all the interfaces:
+# adc,adcan,adcap,adcc,adctotn,adctotp,alan,alap,alarm,alarmc,alcps,alct,
+# cnt,cntc,count,cps,date,
+# duty1,duty2,duty3,duty4,maxan,maxap,maxcps,out,outc,ovruncnt,
+# pc0,pc1,pc2,pc3,
+# period1,period2,
+# pio,pioc,resetcnt,rtcc,selectcnt,stalledcnt,
+# tpm1c,tpm2c,udate,
+# usera,userb,userc,userd,usere,userf,userg,userh,useri,userj,userk,userl,userm,usern,usero,userp
+# not all needed for now:
+interfaces = duty1,duty2,duty3,duty4,tpm1c,tpm2c,period1,period2,usera,userb,userc,userd,usere,userf,userg,userh,useri,userj,userk,userl,userm,usern,usero,userp
+
This was sent by the SourceForge.net collaborative development platform, the world's largest Open Source development site.
|
|
From: <ma...@us...> - 2011-02-05 22:22:03
|
Revision: 281
http://openautomation.svn.sourceforge.net/openautomation/?rev=281&view=rev
Author: makki1
Date: 2011-02-05 22:21:56 +0000 (Sat, 05 Feb 2011)
Log Message:
-----------
add DS2413 (testing ci)
Modified Paths:
--------------
PyWireGate/trunk/owfs_connector/sensors.ini
Modified: PyWireGate/trunk/owfs_connector/sensors.ini
===================================================================
--- PyWireGate/trunk/owfs_connector/sensors.ini 2011-02-05 20:59:08 UTC (rev 280)
+++ PyWireGate/trunk/owfs_connector/sensors.ini 2011-02-05 22:21:56 UTC (rev 281)
@@ -47,6 +47,11 @@
cycle = 1
interfaces = PIO.A,PIO.B,sensed.A,sensed.B,latch.ALL,latch.BYTE,set_alarm
+[DS2413]
+# dual switch /PIO
+cycle = 1
+interfaces = PIO.A,PIO.B,sensed.A,sensed.B,latch.ALL,latch.BYTE,set_alarm
+
[DS2408]
# 8x switch / IO, family 29
# PIO.[0-7] if used as output
This was sent by the SourceForge.net collaborative development platform, the world's largest Open Source development site.
|
Thanks for helping keep SourceForge clean.
X