[oneSIS-users] elf image tg3 eth0 DHCP problem
Brought to you by:
jjengla
Menu
▾
▴
[oneSIS-users] elf image tg3 eth0 DHCP problem
|
From: Will C. <wi...@ro...> - 2010-09-27 21:11:57
|
Hello list, I have an old server that has etherboot 5.2 on the NIC. I have created an image from an OpenSUSE 11.2 server, built a kernel with all the necessary options, configured my ISC DHCP server accordingly, created an initrd with mk-sysimage, and created an elf image with the following command: mkelfImage/objdir/sbin/ mkelfImage --kernel=vmlinuz-2.6.31.12-0.2-ccs --initrd=initrd-2.6.31.12-0.2-ccs --output=2.6.31.12-0.2-ccs.elf --command-line="ip=dhcp root=/dev/nfs rw nfsroot=10.1.2.11:/oneSIS/image-00-20100907 console=tty0 console=ttyS0,115200 panic=60" Here is my console output: Welcome to elfboot, the open sourced starter. January 2002, Eric Biederman. Version 1.3 Found ELF candiate at offset 0 Loading Etherboot version: 5.2.4js1 Dropping non PT_LOAD segment New segment addr 0x20000 size 0x41e65 offset 0xc0 filesize 0x993a (cleaned up) New segment addr 0x20000 size 0x41e65 offset 0xc0 filesize 0x993a Loading Segment: addr: 0x000000007ff8c000 memsz: 0x000000000002c000 filesz: 0x000000000000993a Clearing Segment: addr: 0x000000007ff9593a memsz: 0x00000000000226c6 Loading Segment: addr: 0x000000000004c000 memsz: 0x0000000000015e65 filesz: 0x0000000000000000 Clearing Segment: addr: 0x000000000004c000 memsz: 0x0000000000015e65 Jumping to boot code at 0x20000 ROM segment 0x0000 length 0x0000 reloc 0x00020000 CPU 2498 Mhz Etherboot 5.2.4js1 (GPL) http://etherboot.org ELF64 ELF with TFTP SLAM LACP for [EEPRO100][E1000][3C90X][TG3][IDE] Relocating _text from: [00029930,00063080) to [7fec68b0,7ff00000) ?Probing pci nic... (D)isk or (Q)uit? [tg3-5702X]Ethernet addr: 00:50:45:5C:34:7C Tigon3 [partno(BCM95702A20) rev 1002 PHY(5703)] (PCI:66MHz:32-bit) Link is up at 1000 Mbps, full duplex. Searching for server (DHCP)... ....Me: 10.0.1.28, Server: 10.0.0.11, Gateway 10.0.0.9 Loading 10.0.0.11:2.6.31.12-0.2-ccs.elf ...(ELF)... ...................................................................................................................................done Firmware type: LinuxBIOS [ 0.000000] Linux version 2.6.31.12-0.2-ccs (geeko@buildhost) (gcc version 4.4.1 [gcc-4_4-branch revision 150839] (SUSE Linux) ) #5 SMP PREEMPT Mon Sep 27 13:06:29 CDT 2010 [ 0.000000] Command line: ip=dhcp root=/dev/nfs rw nfsroot=10.1.2.11:/var/lib/oneSIS/image-00-20100907 console=tty0 console=ttyS0,115200 panic=60 [ 0.000000] KERNEL supported cpus: [ 0.000000] Intel GenuineIntel [ 0.000000] AMD AuthenticAMD [ 0.000000] Centaur CentaurHauls [ 0.000000] BIOS-provided physical RAM map: [ 0.000000] BIOS-e820: 0000000000000000 - 0000000000000e14 (reserved) [ 0.000000] BIOS-e820: 0000000000000e14 - 00000000000a0000 (usable) [ 0.000000] BIOS-e820: 00000000000c0000 - 00000000000f0000 (usable) [ 0.000000] BIOS-e820: 00000000000f0000 - 00000000000f0400 (reserved) [ 0.000000] BIOS-e820: 00000000000f0400 - 0000000080000000 (usable) [ 0.000000] DMI not present or invalid. [ 0.000000] last_pfn = 0x80000 max_arch_pfn = 0x400000000 [ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106 [ 0.000000] Scanning 1 areas for low memory corruption [ 0.000000] modified physical RAM map: [ 0.000000] modified: 0000000000000000 - 0000000000000e14 (reserved) [ 0.000000] modified: 0000000000000e14 - 0000000000001000 (usable) [ 0.000000] modified: 0000000000001000 - 0000000000006000 (reserved) [ 0.000000] modified: 0000000000006000 - 00000000000a0000 (usable) [ 0.000000] modified: 00000000000c0000 - 00000000000f0000 (usable) [ 0.000000] modified: 00000000000f0000 - 00000000000f0400 (reserved) [ 0.000000] modified: 00000000000f0400 - 0000000080000000 (usable) [ 0.000000] init_memory_mapping: 0000000000000000-0000000080000000 [ 0.000000] RAMDISK: 00800000 - 008de69c [ 0.000000] ACPI Error: A valid RSDP was not found 20090521 tbxfroot-219 [ 0.000000] Scanning NUMA topology in Northbridge 24 [ 0.000000] Number of nodes 2 [ 0.000000] Node 0 MemBase 0000000000000000 Limit 0000000040000000 [ 0.000000] Node 1 MemBase 0000000040000000 Limit 0000000080000000 [ 0.000000] Using node hash shift of 30 [ 0.000000] found SMP MP-table at [ffff880000000010] 10 [ 0.000000] Intel MultiProcessor Specification v1.4 [ 0.000000] MPTABLE: OEM ID: LNXI [ 0.000000] MPTABLE: Product ID: HDAMA [ 0.000000] MPTABLE: APIC at: 0xFEE00000 [ 0.000000] Bootmem setup node 0 0000000000000000-0000000040000000 [ 0.000000] NODE_DATA [0000000000009000 - 0000000000020fff] [ 0.000000] bootmap [0000000000021000 - 0000000000028fff] pages 8 [ 0.000000] (6 early reservations) ==> bootmem [0000000000 - 0040000000] [ 0.000000] #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000] [ 0.000000] #1 [0000006000 - 0000008000] TRAMPOLINE ==> [0000006000 - 0000008000] [ 0.000000] #2 [0001000000 - 0001e9a230] TEXT DATA BSS ==> [0001000000 - 0001e9a230] [ 0.000000] #3 [0000800000 - 00008de69c] RAMDISK ==> [0000800000 - 00008de69c] [ 0.000000] #4 [000009f000 - 0000100000] BIOS reserved ==> [000009f000 - 0000100000] [ 0.000000] #5 [0000008000 - 0000009000] PGTABLE ==> [0000008000 - 0000009000] [ 0.000000] Bootmem setup node 1 0000000040000000-0000000080000000 [ 0.000000] NODE_DATA [0000000040000000 - 0000000040017fff] [ 0.000000] bootmap [0000000040018000 - 000000004001ffff] pages 8 [ 0.000000] (6 early reservations=> bootmem [0040000000 - 0080000000] [ 0.000000] #0 [0000000000 - 0000001000] BIOS data page [ 0.000000] #1 [0000006000 - 0000008000] TRAMPOLINE [ 0.000000] #2 [0001000000 - 0001e9a230] TEXT DATA BSS [ 0.000000] #3 [0000800000 - 00008de69c] RAMDISK [ 0.000000] #4 [000009f000 - 0000100000] BIOS reserved [ 0.000000] #5 [0000008000 - 0000009000] PGTABLE [ 0.000000] found SMP MP-table at [ffff880000000010] 10 [ 0.000000] Zone PFN ranges: [ 0.000000] DMA 0x00000006 -> 0x00001000 [ 0.000000] DMA32 0x00001000 -> 0x00100000 [ 0.000000] Normal 0x00100000 -> 0x00100000 [ 0.000000] Movable zone start PFN for each node [ 0.000000] early_node_map[4] active PFN ranges [ 0.000000] 0: 0x00000006 -> 0x000000a0 [ 0.000000] 0: 0x000000c0 -> 0x000000f0 [ 0.000000] 0: 0x000000f1 -> 0x00040000 [ 0.000000] 1: 0x00040000 -> 0x00080000 [ 0.000000] Intel MultiProcessor Specification v1.4 [ 0.000000] MPTABLE: OEM ID: LNXI [ 0.000000] MPTABLE: Product ID: HDAMA [ 0.000000] MPTABLE: APIC at: 0xFEE00000 [ 0.000000] Processor #0 (Bootup-CPU) [ 0.000000] Processor #1 [ 0.000000] I/O APIC #2 Version 17 at 0xFEC00000. [ 0.000000] I/O APIC #3 Version 17 at 0xFD200000. [ 0.000000] I/O APIC #4 Version 17 at 0xFD201000. [ 0.000000] Processors: 2 [ 0.000000] SMP: Allowing 2 CPUs, 0 hotplug CPUs [ 0.000000] PM: Registered nosave memory: 0000000000000000 - 0000000000001000 [ 0.000000] PM: Registered nosave memory: 0000000000001000 - 0000000000006000 [ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000c0000 [ 0.000000] PM: Registered nosave memory: 00000000000f0000 - 00000000000f1000 [ 0.000000] Allocating PCI resources starting at 80000000 (gap: 80000000:80000000) [ 0.000000] NR_CPUS:512 nr_cpumask_bits:512 nr_cpu_ids:2 nr_node_ids:2 [ 0.000000] PERCPU: Remapped at ffffc90000000000 with large pages, static data 82784 bytes [ 0.000000] Built 2 zonelists in Node order, mobility grouping on. Total pages: 516758 [ 0.000000] Policy zone: DMA32 [ 0.000000] Kernel command line: ip=dhcp root=/dev/nfs rw nfsroot=10.0.0.11:/var/lib/oneSIS/image-ade-00-20100907 console=tty0 console=ttyS0,115200 panic=60 [ 0.000000] PID hash table entries: 4096 (order: 12, 32768 bytes) [ 0.000000] Initializing CPU#0 [ 0.000000] Checking aperture... [ 0.000000] No AGP bridge found [ 0.000000] Node 0: aperture @ f8000000 size 64 MB [ 0.000000] Node 1: aperture @ f8000000 size 64 MB [ 0.000000] Memory: 2051404k/2097152k available (6888k kernel code, 156k absent, 45592k reserved, 5313k data, 996k init) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] NR_IRQS:4352 nr_irqs:512 [ 0.000000] Fast TSC calibration using PIT [ 0.000000] Detected 2405.226 MHz processor. [ 0.000497] Console: colour dummy device 80x25 [ 0.000501] console [tty0] enabled [ 0.000754] console [ttyS0] enabled [ 0.001010] Calibrating delay loop (skipped), value calculated using timer frequency.. 4810.45 BogoMIPS (lpj=2405226) [ 0.024924] kdb version 4.4 by Keith Owens, Scott Lurndal. Copyright SGI, All Rights Reserved kdb_cmd[0]: defcmd archkdb "" "First line arch debugging" kdb_cmd[7]: defcmd archkdbcpu "" "archkdb with only tasks on cpus" kdb_cmd[14]: defcmd archkdbshort "" "archkdb with less detailed backtrace" kdb_cmd[21]: defcmd archkdbcommon "" "Common arch debugging" [ 0.029169] Security Framework initialized [ 0.030023] AppArmor: AppArmor initialized [ 0.031209] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes) [ 0.033817] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes) [ 0.035583] Mount-cache hash table entries: 256 [ 0.036237] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) [ 0.036998] CPU: L2 Cache: 1024K (64 bytes/line) [ 0.037998] CPU 0/0x0 -> Node 0 [ 0.039014] mce: CPU supports 5 MCE banks [ 0.040008] Performance Counters: AMD PMU driver. [ 0.041999] ... version: 0 [ 0.042996] ... bit width: 48 [ 0.043996] ... generic counters: 4 [ 0.044996] ... value mask: 0000ffffffffffff [ 0.045996] ... max period: 00007fffffffffff [ 0.046995] ... fixed-purpose counters: 0 [ 0.047995] ... counter mask: 000000000000000f [ 0.050563] Setting APIC routing to flat [ 0.051509] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=0 pin2=0 [ 0.062860] CPU0: AMD Hammer stepping 0a [ 0.166974] Booting processor 1 APIC 0x1 ip 0x6000 [ 0.000999] Initializing CPU#1 [ 0.000999] Calibrating delay using timer specific routine.. 4810.07 BogoMIPS (lpj=2405039) [ 0.000999] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) [ 0.000999] CPU: L2 Cache: 1024K (64 bytes/line) [ 0.000999] CPU 1/0x1 -> Node 1 [ 0.000999] mce: CPU supports 5 MCE banks [ 0.000999] x86 PAT enabled: cpu 1, old 0x7040600070406, new 0x7010600070106 [ 0.238687] CPU1: AMD Hammer stepping 0a [ 0.241017] Brought up 2 CPUs [ 0.243968] Total of 2 processors activated (9620.53 BogoMIPS). [ 0.250295] devtmpfs: initialized [ 0.254987] Booting paravirtualized kernel on bare hardware [ 0.261002] regulator: core version 0.5 [ 0.263994] Time: 20:41:41 Date: 09/27/10 [ 0.269052] NET: Registered protocol family 16 [ 0.273119] TOM: 0000000080000000 aka 2048M [ 0.277970] TOM2: 0000000080000000 aka 2048M [ 0.281963] run of slot in ranges [ 0.284958] run of slot in ranges [ 0.288346] PCI: Using configuration type 1 for base access [ 0.296121] bio: create slab <bio-0> at 0 [ 0.300040] ACPI: Interpreter disabled. [ 0.304170] SCSI subsystem initialized [ 0.307994] usbcore: registered new interface driver usbfs [ 0.313978] usbcore: registered new interface driver hub [ 0.319015] usbcore: registered new device driver usb [ 0.324066] PCI: Probing PCI hardware [ 0.328654] pci 0000:02:03.0: PME# supported from D3hot D3cold [ 0.335005] pci 0000:02:03.0: PME# disabled [ 0.339081] pci 0000:02:04.0: PME# supported from D3hot D3cold [ 0.345003] pci 0000:02:04.0: PME# disabled [ 0.349612] PCI: Discovered primary peer bus 01 [IRQ] [ 0.355019] pci 0000:01:04.3: default IRQ router [1022:746b] [ 0.364813] AppArmor: AppArmor Filesystem Enabled [ 0.370005] pnp: PnP ACPI: disabled [ 0.375033] pci 0000:04:06.0: BAR 6: no parent found for of device [0xfff80000-0xfff9ffff] [ 0.383036] pci 0000:01:01.0: PCI bridge, secondary bus 0000:02 [ 0.389002] pci 0000:01:01.0: IO window: disabled [ 0.394005] pci 0000:01:01.0: MEM window: 0xfd100000-0xfd1fffff [ 0.400004] pci 0000:01:01.0: PREFETCH window: disabled [ 0.406004] pci 0000:01:02.0: PCI bridge, secondary bus 0000:03 [ 0.412002] pci 0000:01:02.0: IO window: disabled [ 0.417005] pci 0000:01:02.0: MEM window: disabled [ 0.422003] pci 0000:01:02.0: PREFETCH window: disabled [ 0.427006] pci 0000:01:03.0: PCI bridge, secondary bus 0000:04 [ 0.433003] pci 0000:01:03.0: IO window: 0x1000-0x1fff [ 0.438005] pci 0000:01:03.0: MEM window: 0xfc000000-0xfd0fffff [ 0.444005] pci 0000:01:03.0: PREFETCH window: 0x80000000-0x800fffff [ 0.451154] NET: Registered protocol family 2 [ 0.455200] IP route cache hash table entries: 65536 (order: 7, 524288 bytes) [ 0.463765] TCP established hash table entries: 262144 (order: 10, 4194304 bytes) [ 0.473971] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes) [ 0.481318] TCP: Hash tables configured (established 262144 bind 65536) [ 0.488003] TCP reno registered [ 0.491230] NET: Registered protocol family 1 [ 0.496119] Unpacking initramfs... [ 0.516618] Freeing initrd memory: 889k freed [ 0.521788] platform rtc_cmos: registered platform RTC device (no PNP device found) [ 0.530386] Scanning for low memory corruption every 60 seconds [ 0.536235] audit: initializing netlink socket (disabled) [ 0.542023] type=2000 audit(1285620100.542:1): initialized [ 0.551038] HugeTLB registered 2 MB page size, pre-allocated 0 pages [ 0.557146] VFS: Disk quotas dquot_6.5.2 [ 0.561092] Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 0.568325] Installing knfsd (copyright (C) 1996 ok...@mo...). [ 0.575394] msgmni has been set to 1002 [ 0.579115] alg: No test for stdrng (krng) [ 0.580047] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) [ 0.588005] io scheduler noop registered [ 0.592002] io scheduler anticipatory registered [ 0.596002] io scheduler deadline registered [ 0.601040] io scheduler cfq registered (default) [ 0.605129] pci 0000:01:01.0: MSI quirk detected; subordinate MSI disabled [ 0.612009] disabled boot interrupts on PCI device 0x1022:0x7450 [ 0.618003] pci 0000:01:01.0: AMD8131 rev 12 detected; disabling PCI-X MMRBC [ 0.625005] pci 0000:01:02.0: MSI quirk detected; subordinate MSI disabled [ 0.632003] disabled boot interrupts on PCI device 0x1022:0x7450 [ 0.638002] pci 0000:01:02.0: AMD8131 rev 12 detected; disabling PCI-X MMRBC [ 0.645013] boot interrupts on PCI device 0x1022:0x746b already disabled [ 0.652119] pci-stub: invalid id string "" [ 0.658142] Non-volatile memory driver v1.3 [ 0.663003] Linux agpgart interface v0.103 [ 0.667006] Serial: 8250/16550 driver, 8 ports, IRQ sharing disabled [ 0.673110] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 0.679217] serial 0000:01:04.6: can't find IRQ for PCI INT B; probably buggy MP table [ 0.680113] Intel(R) PRO/1000 Network Driver - version 7.3.21-k3-NAPI [ 0.687005] Copyright (c) 1999-2006 Intel Corporation. [ 0.692023] e1000e: Intel(R) PRO/1000 Network Driver - 1.0.2-k2 [ 0.698002] e1000e: Copyright (c) 1999-2008 Intel Corporation. [ 0.704025] Intel(R) Gigabit Ethernet Network Driver - version 1.3.16-k2 [ 0.711002] Copyright (c) 2007-2009 Intel Corporation. [ 0.716018] Intel(R) Virtual Function Network Driver - version 1.0.0-k0 [ 0.722002] Copyright (c) 2009 Intel Corporation. [ 0.727072] jme: JMicron JMC2XX ethernet driver version 1.0.4 [ 0.733057] ns83820.c: National Semiconductor DP83820 10/100/1000 driver. [ 0.740043] tg3.c:v3.99 (April 20, 2009) [ 0.741020] tg3 0000:02:03.0: PCI->APIC IRQ transform: INT A -> IRQ 19 [ 0.744022] tg3 0000:02:03.0: PME# disabled [ 0.770751] eth0: Tigon3 [partno(BCM95702A20) rev 1002] (PCI:66MHz:32-bit) MAC address 00:50:45:5c:34:7c [ 0.771003] eth0: attached PHY is 5703 (10/100/1000Base-T Ethernet) (WireSpeed[1]) [ 0.772002] eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] TSOcap[1] [ 0.773002] eth0: dma_rwctrl[763f0000] dma_mask[64-bit] [ 0.775009] tg3 0000:02:04.0: PCI->APIC IRQ transform: INT A -> IRQ 19 [ 0.778021] tg3 0000:02:04.0: PME# disabled [ 0.811684] eth1: Tigon3 [partno(BCM95702A20) rev 1002] (PCI:66MHz:32-bit) MAC address 00:50:45:5c:34:7d [ 0.812002] eth1: attached PHY is 5703 (10/100/1000Base-T Ethernet) (WireSpeed[1]) [ 0.813002] eth1: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] TSOcap[1] [ 0.814002] eth1: dma_rwctrl[763f0000] dma_mask[64-bit] [ 0.815033] Broadcom NetXtreme II CNIC Driver cnic v2.0.0 (May 21, 2009) [ 0.822024] sky2 driver version 1.23 [ 0.825071] Fixed MDIO Bus: probed [ 0.829074] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 0.835026] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 0.842010] ohci_hcd 0000:04:00.0: can't find IRQ for PCI INT D; probably buggy MP table [ 0.843004] ohci_hcd 0000:04:00.0: Found HC with no IRQ. Check BIOS/PCI 0000:04:00.0 setup! [ 0.844004] ohci_hcd 0000:04:00.0: init 0000:04:00.0 fail, -19 [ 0.846009] ohci_hcd 0000:04:00.1: can't find IRQ for PCI INT D; probably buggy MP table [ 0.847004] ohci_hcd 0000:04:00.1: Found HC with no IRQ. Check BIOS/PCI 0000:04:00.1 setup! [ 0.848003] ohci_hcd 0000:04:00.1: init 0000:04:00.1 fail, -19 [ 0.849015] uhci_hcd: USB Universal Host Controller Interface driver [ 0.855057] Initializing USB Mass Storage driver... [ 0.860018] usbcore: registered new interface driver usb-storage [ 0.866004] USB Mass Storage support registered. [ 0.871018] usbcore: registered new interface driver libusual [ 0.876014] usbcore: registered new interface driver ums-alauda [ 0.882015] usbcore: registered new interface driver ums-cypress [ 0.888014] usbcore: registered new interface driver ums-datafab [ 0.894015] usbcore: registered new interface driver ums-freecom [ 0.900016] usbcore: registered new interface driver ums-isd200 [ 0.906015] usbcore: registered new interface driver ums-jumpshot [ 0.912015] usbcore: registered new interface driver ums-karma [ 0.918012] usbcore: registered new interface driver ums-onetouch [ 0.924016] usbcore: registered new interface driver ums-sddr09 [ 0.930012] usbcore: registered new interface driver ums-sddr55 [ 0.936012] usbcore: registered new interface driver ums-usbat [ 0.942039] PNP: No PS/2 controller found. Probing ports directly. [ 1.200359] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 1.206084] mice: PS/2 mouse device common for all mice [ 1.211082] rtc_cmos rtc_cmos: rtc core: registered rtc_cmos as rtc0 [ 1.217042] rtc0: alarms up to one day, 114 bytes nvram [ 1.223014] cpuidle: using governor ladder [ 1.227003] cpuidle: using governor menu [ 1.231266] usbcore: registered new interface driver hiddev [ 1.237019] usbcore: registered new interface driver usbhid [ 1.242003] usbhid: v2.6:USB HID core driver [ 1.261003] Clocksource tsc unstable (delta = 98627944 ns) [ 1.344683] TCP cubic registered [ 1.348081] NET: Registered protocol family 10 [ 1.353532] lo: Disabled Privacy Extensions [ 1.359121] RPC: Registered udp transport module. [ 1.363003] RPC: Registered tcp transport module. [ 1.368020] lib80211: common routines for IEEE802.11 drivers [ 1.374168] registered taskstats version 1 [ 1.378120] Magic number: 10:303:701 [ 1.382076] rtc_cmos rtc_cmos: setting system clock to 2010-09-27 20:41:42 UTC (1285620102) [ 1.892503] tg3 0000:02:03.0: firmware: using built-in firmware tigon/tg3_tso.bin [ 1.900012] tg3 0000:02:03.0: PME# disabled [ 2.155384] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 2.156018] tg3 0000:02:04.0: firmware: using built-in firmware tigon/tg3_tso.bin [ 2.157009] tg3 0000:02:04.0: PME# disabled [ 2.418872] ADDRCONF(NETDEV_UP): eth1: link is not ready [ 3.420005] Sending DHCP requests ...... timed out! [ 91.818839] tg3: eth0: Link is up at 1000 Mbps, full duplex. [ 91.819018] tg3: eth0: Flow control is off for TX and off for RX. [ 91.954462] tg3 0000:02:03.0: PME# enabled [ 92.211461] tg3 0000:02:04.0: PME# enabled [ 92.223506] IP-Config: Retrying forever (NFS root)... [ 92.725025] tg3 0000:02:03.0: PME# disabled [ 92.997238] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 92.998026] tg3 0000:02:04.0: PME# disabled [ 93.270193] ADDRCONF(NETDEV_UP): eth1: link is not ready [ 94.272020] Sending DHCP requests ...... timed out! [ 172.703820] tg3: eth0: Link is up at 1000 Mbps, full duplex. [ 172.704019] tg3: eth0: Flow control is off for TX and off for RX. [ 172.839462] tg3 0000:02:03.0: PME# enabled [ 173.096462] tg3 0000:02:04.0: PME# enabled [ 173.108505] IP-Config: Retrying forever (NFS root)... [ 173.610026] tg3 0000:02:03.0: PME# disabled [ 173.882286] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 173.883028] tg3 0000:02:04.0: PME# disabled [ 174.155175] ADDRCONF(NETDEV_UP): eth1: link is not ready [ 175.157020] Sending DHCP requests ...... timed out! [ 249.992811] tg3: eth0: Link is up at 1000 Mbps, full duplex. [ 249.993019] tg3: eth0: Flow control is off for TX and off for RX. [ 250.128462] tg3 0000:02:03.0: PME# enabled [ 250.385462] tg3 0000:02:04.0: PME# enabled [ 250.397506] IP-Config: Retrying forever (NFS root)... [ 250.899026] tg3 0000:02:03.0: PME# disabled [ 251.171233] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 251.172027] tg3 0000:02:04.0: PME# disabled [ 251.444234] ADDRCONF(NETDEV_UP): eth1: link is not ready [ 252.446020] Sending DHCP requests ..... I don't understand why the link shows ready then not ready repeatedly. Can anyone point me towards a solution? Thank you, -Will |