Re: [Ndiswrapper-general] 0.9-pre2 release
Status: Beta
Brought to you by:
pgiri
Menu
▾
▴
Re: [Ndiswrapper-general] 0.9-pre2 release
|
From: Andrew S. B. <ne...@my...> - 2004-07-30 13:00:29
|
Hi all!
Again RTL8081L driver (Linksys WPC11 v.4 PCMCIA adapter)
Since version 0.9-pre1 I was able to initialize wlan0. At least it
appeared on dmesg. However I can't still access AP :( When I set essid
it is displayed untill I do invocation of iwconfig or ipconfig. I tested
pre2 version just right away and still cant get it working. Does anybody
have any suggestions?
Here is the logs:
$ dmesg
ndiswrapper version 0.9-pre2 loaded
ndiswrapper: driver rtl8180.sys added
PCI: Enabling device 0000:02:00.0 (0000 -> 0003)
PCI: Setting latency timer of device 0000:02:00.0 to 64
ndiswrapper: using irq 10
wlan0: ndiswrapper ethernet device 00:0c:41:c1:dc:39 using driver
rtl8180.sys
ndiswrapper device wlan0 supports WPA with AES/CCMP and TKIP ciphers
$ iwconfig wlan0 mode Auto
$ iwconfig wlan0 essid entrex
$ iwconfig
$ ifconfig wlan0 up
$ ifconfig wlan0 192.168.76.99 netmask 255.255.255.0
$ sudo /usr/sbin/iwconfig wlan0 essid entrex
$ sudo /usr/sbin/iwconfig
lo no wireless extensions.
eql no wireless extensions.
irda0 no wireless extensions.
eth0 no wireless extensions.
eth1 no wireless extensions.
wlan0 IEEE 802.11b ESSID:"entrex"
Mode:Ad-Hoc Frequency:2.412GHz Cell: 02:E0:E8:A5:72:A0
Bit Rate:11Mb/s Tx-Power:20 dBm Sensitivity=0/3
RTS thr:2432 B Fragment thr:2432 B
Encryption key:off
Power Management:off
Link Quality:100/100 Signal level:-73 dBm Noise level:-256 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
$ ping -I wlan0 192.168.76.28
PING 192.168.76.28 (192.168.76.28) from 192.168.76.21 wlan0: 56(84)
bytes of data.
From 192.168.76.99 icmp_seq=1 Destination Host Unreachable
From 192.168.76.99 icmp_seq=2 Destination Host Unreachable
From 192.168.76.99 icmp_seq=3 Destination Host Unreachable
--- 192.168.76.28 ping statistics ---
5 packets transmitted, 0 received, +3 errors, 100% packet loss, time 3999ms
, pipe 3
$ sudo /usr/sbin/iwconfig
lo no wireless extensions.
eql no wireless extensions.
irda0 no wireless extensions.
eth0 no wireless extensions.
eth1 no wireless extensions.
wlan0 IEEE 802.11b ESSID:off/any
Mode:Auto Frequency:2.412GHz Access Point: 00:00:00:00:00:00
Bit Rate:11Mb/s Tx-Power:20 dBm Sensitivity=0/3
RTS thr:2432 B Fragment thr:2432 B
Encryption key:off
Power Management:off
Link Quality:100/100 Signal level:-73 dBm Noise level:-256 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
Best regards,
Andrew.
Pontus Fuchs wrote:
> Hi,
>
> 0.9-pre2 is available at sourceforge. Please try this release and
> report if you have problems.
>
> Some bugs found from 0.9-pre1 testing has been fixed in this release.
> Give it a test drive and if no serious problems are found 0.9 should be
> ready real soon now.
>
> Pontus
>
>
>
>
>
> -------------------------------------------------------
> This SF.Net email is sponsored by OSTG. Have you noticed the changes on
> Linux.com, ITManagersJournal and NewsForge in the past few weeks? Now,
> one more big change to announce. We are now OSTG- Open Source Technology
> Group. Come see the changes on the new OSTG site. www.ostg.com
> _______________________________________________
> Ndiswrapper-general mailing list
> Ndi...@li...
> https://lists.sourceforge.net/lists/listinfo/ndiswrapper-general
>
|