Re: [Ndiswrapper-general] (Partail) success with 0.8 and rtl8180
Status: Beta
Brought to you by:
pgiri
From: Bret H. <bh...@el...> - 2004-06-10 16:59:55
|
On Thu, 2004-06-10 at 07:30, miguel sofer wrote: > Romano Giannetti wrote: > > Good morning to all, > > And now a little question... could anyone of you that is using this card > > successfully send me the XP driver? I just have the last one from > > realtek site, and maybe downgrading the driver to the one that works for > > you I can solve my problems. > > No success here yet :( > > You can download other versions of the xp driver from realtek's site, at > ftp://202.65.194.18/cn/wlan/rtl8180l/ > ftp://202.65.194.18/cn/wlan/rtl8180l/ > > These are the sites of the second and third link in Realtek's download > page; the first link has a smaller selection (go figure). > > miguel > > Meant to send this to the list sorry Miguel FWIW I finally got an 8180 based dlink dwl610 card to come up w/o WEP using the dlink driver from the dlink UK site (card is not supported here in the US) I tried and tried with various realtek drivers but never could get ndiswrapper -l to report present. This is on fedora 1,kernel 2.4.22-1.2188.nptl, ndiswrapper 0.8 rc2. I tried to get the latest cvs but kept getting errors about perms on a temp dir. There is something funky still but I have not had time to dink with it but will today. Here is the output of several pertinent commands if it helps: [root@install238 DRIVERS]# lspci -n 00:00.0 Class 0600: 1106:3123 00:01.0 Class 0604: 1106:b091 00:0a.0 Class 0607: 1180:0476 (rev 80) 00:0a.1 Class 0607: 1180:0476 (rev 80) 00:0d.0 Class 0c00: 1106:3044 (rev 80) 00:10.0 Class 0c03: 1106:3038 (rev 80) 00:10.1 Class 0c03: 1106:3038 (rev 80) 00:10.2 Class 0c03: 1106:3038 (rev 80) 00:10.3 Class 0c03: 1106:3104 (rev 82) 00:11.0 Class 0601: 1106:3177 00:11.1 Class 0101: 1106:0571 (rev 06) 00:12.0 Class 0200: 1106:3065 (rev 74) 01:00.0 Class 0300: 1106:3122 (rev 03) 02:00.0 Class 0200: 1186:3300 (rev 20) [root@install238 DRIVERS]# lspci -vs 02:00.0 02:00.0 Ethernet controller: D-Link System Inc: Unknown device 3300 (rev 20) Subsystem: D-Link System Inc: Unknown device 3300 Flags: bus master, medium devsel, latency 64, IRQ 12 I/O ports at 9000 [size=256] Memory at de003000 (32-bit, non-prefetchable) [size=512] Capabilities: [50] Power Management version 2 Here is the part I do not like: Any ideas why I can't see this? [root@install238 DRIVERS]# cardctl ident Socket 0: no product info available Socket 1: no product info available [root@install238 DRIVERS]# ndiswrapper -l Installed ndis drivers: netdlwl present [root@install238 DRIVERS]# [root@install238 devices]# ifconfig wlan0 wlan0 Link encap:Ethernet HWaddr 00:0D:88:58:52:A4 inet addr:10.23.0.146 Bcast:10.23.0.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:793952 errors:0 dropped:0 overruns:0 frame:0 TX packets:683415 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:91905223 (87.6 Mb) TX bytes:197549219 (188.3 Mb) Interrupt:12 Memory:de003000-de003024 [root@install238 devices]# iwconfig wlan0 wlan0 IEEE 802.11b ESSID:"havetoguess" Nickname:"install238.brets.elevating.com" Mode:Managed Frequency:2.437GHz Access Point: 00:0F:66:22:2B:01 Bit Rate=11Mb/s Tx-Power:20 dBm Sensitivity=0/3 RTS thr=2432 B Fragment thr=2432 B Encryption key:off Power Management:off Link Quality:100/100 Signal level:-71 dBm Noise level:-256 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 |