From: Nick E. <nic...@gm...> - 2013-10-13 03:18:59
|
Hi, I am new to this list, because for years motion has run effortlessly, until today upgrade (upgrade was for use of auth to access cameras remotely, the mobile device vpn clients are atrociously hopeless in stability so when I saw this I jumped at it.) so pledase forgive my ignorance if this was previously discussed I moved my two webcams running under motion old long time stable 3.2.12 today, to current git motion-master. built without sdl no other options Both camera's fail with new configs on new version, only real changes were brightness (and yes tried that at default as well) and the storage locations cameras both work fine if I run the old version under /opt/ with the old versions conf so cameras are fine, these are on slackware 13.1 with no GUI, running kernel 3.10.15, both built against same ffmpeg The two servers are identical in configs and kernel and other software The two cameras are ID 0ac8:3420 Z-Star Microelectronics Corp. Venus USB2.0 Camera ID 046d:08d9 Logitech, Inc. QuickCam IM/Connect daemon on process_id_file /var/run/motion.pid setup_mode off logfile /var/log/motion.log log_level 6 log_type all videodevice /dev/video0 v4l2_palette 17 input -1 norm 0 frequency 0 rotate 0 width 320 height 240 framerate 100 minimum_frame_time 0 netcam_keepalive off netcam_tolerant_check off auto_brightness on brightness 200 contrast 0 saturation 0 hue 0 roundrobin_frames 1 roundrobin_skip 1 switchfilter off threshold 1500 threshold_tune off noise_level 32 noise_tune on despeckle_filter EedDl smart_mask_speed 0 lightswitch 20 minimum_motion_frames 1 pre_capture 0 post_capture 0 event_gap 60 max_movie_time 3600 emulate_motion off output_pictures on output_debug_pictures off quality 75 picture_type jpeg ffmpeg_output_movies on ffmpeg_output_debug_movies off ffmpeg_timelapse 0 ffmpeg_timelapse_mode daily ffmpeg_bps 500000 ffmpeg_variable_bitrate 0 ffmpeg_video_codec mpeg4 ffmpeg_deinterlace off use_extpipe off snapshot_interval 0 locate_motion_mode on locate_motion_style box text_right %Y-%m-%d\n%T-%q text_left Cam %t Shop Mail 1 text_changes off text_event %Y%m%d%H%M%S text_double off target_dir /var/www/html/secure/cam1 snapshot_filename %v-%Y%m%d%H%M%S-cam%t picture_filename %v-%Y%m%d%H%M%S-%q movie_filename %v-%Y%m%d%H%M%S timelapse_filename %Y%m%d-timelapse ipv6_enabled off stream_port 8081 stream_quality 75 stream_motion off stream_maxrate 5 stream_localhost off stream_limit 0 stream_auth_method 1 stream_authentication xxxxxx:xxxxxxx webcontrol_port 8080 webcontrol_localhost on webcontrol_html_output on track_type 0 track_auto off track_iomojo_id 0 track_step_angle_x 10 track_step_angle_y 10 track_move_wait 10 track_speed 255 track_stepsize 40 quiet on on_movie_end /usr/bin/scp %f xxxxxxx I have tried without and with " LD_PRELOAD=/usr/lib/libv4l/v4l2convert.so motion" which is what some people have suggested, to no avail. I guess something has changed because of Config palette index 17 (YU12) doesn't work, amongst other errors :) as below, Any help much appreciated, Thanks Nikki Oct 13 11:33:45 fox motion: [0] [NTC] [ALL] main: Thread 1 is from /usr/local/etc/motion.conf Oct 13 11:33:45 fox motion: [0] [NTC] [ALL] main: Thread 1 is device: /dev/video0 input -1 Oct 13 11:33:45 fox motion: [0] [NTC] [ALL] main: Stream port 8081 Oct 13 11:33:45 fox motion: [0] [NTC] [ALL] main: Waiting for threads to finish, pid: 31469 Oct 13 11:33:45 fox motion: [1] [NTC] [ALL] motion_init: Thread 1 started , motion detection Enabled Oct 13 11:33:45 fox motion: [1] [NTC] [VID] vid_v4lx_start: Using videodevice /dev/video0 and input -1 Oct 13 11:33:45 fox motion: [1] [NTC] [VID] v4l2_get_capability: ------------------------ cap.driver: "gspca_ zc3xx" cap.card: "USB Camera (046d:08d9)" cap.bus_info: "usb-0000:00:1d.2-1" cap.capabilities=0x85000001 ----- ------------------- Oct 13 11:33:45 fox motion: [1] [NTC] [VID] v4l2_get_capability: - VIDEO_CAPTURE Oct 13 11:33:45 fox motion: [1] [NTC] [VID] v4l2_get_capability: - READWRITE Oct 13 11:33:45 fox motion: [1] [NTC] [VID] v4l2_get_capability: - STREAMING Oct 13 11:33:45 fox motion: [1] [NTC] [VID] v4l2_select_input: name = "gspca_zc3xx", type 0x00000002, status 00000000 Oct 13 11:33:45 fox motion: [1] [NTC] [VID] v4l2_select_input: - CAMERA Oct 13 11:33:45 fox motion: [1] [WRN] [VID] v4l2_select_input: Device doesn't support VIDIOC_G_STD Oct 13 11:33:45 fox motion: [1] [NTC] [VID] v4l2_set_pix_format: Config palette index 17 (YU12) doesn't work. Oct 13 11:33:45 fox motion: [1] [NTC] [VID] v4l2_set_pix_format: Supported palettes: Oct 13 11:33:45 fox motion: [1] [NTC] [VID] v4l2_set_pix_format: (0) JPEG (JPEG) Oct 13 11:33:45 fox motion: [1] [NTC] [VID] v4l2_set_pix_format: 0 - JPEG (compressed : 1) (0x4745504a) Oct 13 11:33:45 fox motion: [1] [NTC] [VID] v4l2_set_pix_format Selected palette JPEG Oct 13 11:33:45 fox motion: [1] [NTC] [VID] v4l2_do_set_pix_format: Testing palette JPEG (320x240) Oct 13 11:33:45 fox motion: [1] [NTC] [VID] v4l2_do_set_pix_format: Using palette JPEG (320x240) bytesperlines 320 sizeimage 29390 colorspace 00000007 Oct 13 11:33:45 fox motion: [1] [NTC] [VID] v4l2_scan_controls: found control 0x00980900, "Brightness", range 0,255 Oct 13 11:33:45 fox motion: [1] [NTC] [VID] v4l2_scan_controls: ^I"Brightness", default 128, current 128 Oct 13 11:33:45 fox motion: [1] [NTC] [VID] v4l2_scan_controls: found control 0x00980901, "Contrast", range 0,255 Oct 13 11:33:45 fox motion: [1] [NTC] [VID] v4l2_scan_controls: ^I"Contrast", default 128, current 128 Oct 13 11:33:45 fox motion: [1] [NTC] [VID] v4l2_scan_controls: ^I"Contrast", default 128, current 128 Oct 13 11:33:45 fox motion: [1] [NTC] [VID] v4l2_scan_controls: found control 0x00980910, "Gamma", range 1,6 Oct 13 11:33:45 fox motion: [1] [NTC] [VID] v4l2_scan_controls: ^I"Gamma", default 4, current 4 Oct 13 11:33:45 fox motion: [1] [NTC] [VID] v4l2_scan_controls: found control 0x00980911, "Exposure", range 781,18750 Oct 13 11:33:45 fox motion: [1] [NTC] [VID] v4l2_scan_controls: ^I"Exposure", default 2343, current 2343 Oct 13 11:33:45 fox motion: [1] [NTC] [VID] v4l2_scan_controls: found control 0x00980912, "Gain, Automatic", range 0,1 Oct 13 11:33:45 fox motion: [1] [NTC] [VID] v4l2_scan_controls: ^I"Gain, Automatic", default 1, current 1 Oct 13 11:33:45 fox motion: [0] [NTC] [STR] httpd_run: motion-httpd testing : IPV4 addr: 127.0.0.1 port: 8080 Oct 13 11:33:45 fox motion: [0] [NTC] [STR] httpd_run: motion-httpd Bound : IPV4 addr: 127.0.0.1 port: 8080 Oct 13 11:33:45 fox motion: [0] [NTC] [STR] httpd_run: motion-httpd/Git-8619d7c17ce112e7196975905c6e840f345141ba running, accepting connections Oct 13 11:33:45 fox motion: [0] [NTC] [STR] httpd_run: motion-httpd: waiting for data on 127.0.0.1 port TCP 8080 Oct 13 11:33:47 fox motion: [1] [NTC] [VID] vid_v4lx_start: Using V4L2 Oct 13 11:33:47 fox motion: [1] [NTC] [ALL] image_ring_resize: Resizing pre_capture buffer to 1 items Oct 13 11:33:47 fox motion: [1] [NTC] [VID] v4l2_set_control: setting control "Brightness" to 40 (ret 0 ) Oct 13 11:33:49 fox motion: [1] [NTC] [VID] v4l2_set_control: setting control "Brightness" to 81 (ret 0 ) Oct 13 11:33:51 fox motion: [1] [NTC] [VID] v4l2_set_control: setting control "Brightness" to 122 (ret 0 ) Oct 13 11:33:53 fox motion: [1] [NTC] [VID] v4l2_set_control: setting control "Brightness" to 163 (ret 0 ) Oct 13 11:33:55 fox motion: [1] [NTC] [VID] v4l2_set_control: setting control "Brightness" to 204 (ret 0 ) Oct 13 11:33:57 fox motion: [1] [ERR] [ALL] motion_init: Error capturing first image Oct 13 11:33:57 fox motion: [1] [NTC] [STR] http_bindsock: motion-stream testing : IPV4 addr: 0.0.0.0 port: 8081 Oct 13 11:33:57 fox motion: [1] [NTC] [STR] http_bindsock: motion-stream Bound : IPV4 addr: 0.0.0.0 port: 8081 Oct 13 11:33:57 fox motion: [1] [NTC] [ALL] motion_init: Started motion-stream server in port 8081 auth Enabled Oct 13 11:33:57 fox motion: [1] [NTC] [VID] v4l2_set_control: setting control "Brightness" to 219 (ret 0 ) Oct 13 11:33:57 fox motion: [1] [ERR] [ALL] motion_loop: Video device fatal error - Closing video device Oct 13 11:33:57 fox motion: [1] [NTC] [VID] vid_close: Closing video device /dev/video0 Oct 13 11:34:00 fox motion: [1] [WRN] [ALL] motion_loop: Retrying until successful connection with camera Oct 13 11:34:00 fox motion: [1] [NTC] [VID] vid_v4lx_start: Using videodevice /dev/video0 and input -1 Oct 13 11:34:00 fox motion: [1] [NTC] [VID] v4l2_get_capability: ------------------------ cap.driver: "gspca_zc3xx" cap.card: "USB Camera (046d:08d9)" cap.bus_info: "usb-0000:00:1d.2-1" cap.capabilities=0x85000001 ------------------------ Oct 13 11:34:00 fox motion: [1] [NTC] [VID] v4l2_get_capability: - VIDEO_CAPTURE Oct 13 11:34:00 fox motion: [1] [NTC] [VID] v4l2_get_capability: - READWRITE Oct 13 11:34:00 fox motion: [1] [NTC] [VID] v4l2_get_capability: - STREAMING Oct 13 11:34:00 fox motion: [1] [NTC] [VID] v4l2_select_input: name = "gspca_zc3xx", type 0x00000002, status 00000000 Oct 13 11:34:00 fox motion: [1] [NTC] [VID] v4l2_select_input: - CAMERA Oct 13 11:34:00 fox motion: [1] [WRN] [VID] v4l2_select_input: Device doesn't support VIDIOC_G_STD Oct 13 11:34:00 fox motion: [1] [NTC] [VID] v4l2_set_pix_format: Config palette index 17 (YU12) doesn't work. Oct 13 11:34:00 fox motion: [1] [NTC] [VID] v4l2_set_pix_format: Supported palettes: Oct 13 11:34:00 fox motion: [1] [NTC] [VID] v4l2_set_pix_format: (0) JPEG (JPEG) Oct 13 11:34:00 fox motion: [1] [NTC] [VID] v4l2_set_pix_format: 0 - JPEG (compressed : 1) (0x4745504a) Oct 13 11:34:00 fox motion: [1] [NTC] [VID] v4l2_set_pix_format Selected palette JPEG Oct 13 11:34:00 fox motion: [1] [NTC] [VID] v4l2_do_set_pix_format: Testing palette JPEG (320x240) Oct 13 11:34:00 fox motion: [1] [NTC] [VID] v4l2_do_set_pix_format: Using palette JPEG (320x240) bytesperlines 320 sizeimage 29390 colorspace 00000007 Oct 13 11:34:00 fox motion: [1] [NTC] [VID] v4l2_scan_controls: found control 0x00980900, "Brightness", range 0,255 Oct 13 11:34:00 fox motion: [1] [NTC] [VID] v4l2_scan_controls: ^I"Brightness", default 128, current 219 Oct 13 11:34:00 fox motion: [1] [NTC] [VID] v4l2_scan_controls: found control 0x00980901, "Contrast", range 0,255 Oct 13 11:34:00 fox motion: [1] [NTC] [VID] v4l2_scan_controls: ^I"Contrast", default 128, current 128 Oct 13 11:34:00 fox motion: [1] [NTC] [VID] v4l2_scan_controls: found control 0x00980910, "Gamma", range 1,6 Oct 13 11:34:00 fox motion: [1] [NTC] [VID] v4l2_scan_controls: ^I"Gamma", default 4, current 4 Oct 13 11:34:00 fox motion: [1] [NTC] [VID] v4l2_scan_controls: found control 0x00980911, "Exposure", range 781,18750 Oct 13 11:34:00 fox motion: [1] [NTC] [VID] v4l2_scan_controls: ^I"Exposure", default 2343, current 2343 Oct 13 11:34:00 fox motion: [1] [NTC] [VID] v4l2_scan_controls: found control 0x00980912, "Gain, Automatic", range 0,1 Oct 13 11:34:00 fox motion: [1] [NTC] [VID] v4l2_scan_controls: ^I"Gain, Automatic", default 1, current 1 Oct 13 11:34:02 fox motion: [1] [NTC] [VID] vid_v4lx_start: Using V4L2 Oct 13 11:34:02 fox motion: [1] [NTC] [VID] v4l2_set_control: setting control "Brightness" to 14 (ret 0 ) Oct 13 11:34:02 fox motion: [1] [ERR] [ALL] motion_loop: Video device fatal error - Closing video device Oct 13 11:34:02 fox motion: [1] [NTC] [VID] vid_close: Closing video device /dev/video0 Oct 13 11:34:10 fox motion: [1] [WRN] [ALL] motion_loop: Retrying until successful connection with camera Oct 13 11:34:10 fox motion: [1] [NTC] [VID] vid_v4lx_start: Using videodevice /dev/video0 and input -1 Oct 13 11:34:10 fox motion: [1] [NTC] [VID] v4l2_get_capability: ------------------------ cap.driver: "gspca_zc3xx" cap.card: "USB Camera (046d:08d9)" cap.bus_info: "usb-0000:00:1d.2-1" cap.capabilities=0x85000001 ------------------------ Oct 13 11:34:10 fox motion: [1] [NTC] [VID] v4l2_get_capability: - VIDEO_CAPTURE Oct 13 11:34:10 fox motion: [1] [NTC] [VID] v4l2_get_capability: - READWRITE Oct 13 11:34:10 fox motion: [1] [NTC] [VID] v4l2_get_capability: - STREAMING Oct 13 11:34:10 fox motion: [1] [NTC] [VID] v4l2_select_input: name = "gspca_zc3xx", type 0x00000002, status 00000000 Oct 13 11:34:10 fox motion: [1] [NTC] [VID] v4l2_select_input: - CAMERA Oct 13 11:34:10 fox motion: [1] [WRN] [VID] v4l2_select_input: Device doesn't support VIDIOC_G_STD Oct 13 11:34:10 fox motion: [1] [NTC] [VID] v4l2_set_pix_format: Config palette index 17 (YU12) doesn't work. Oct 13 11:34:10 fox motion: [1] [NTC] [VID] v4l2_set_pix_format: Supported palettes: Oct 13 11:34:10 fox motion: [1] [NTC] [VID] v4l2_set_pix_format: (0) JPEG (JPEG) Oct 13 11:34:10 fox motion: [1] [NTC] [VID] v4l2_set_pix_format: 0 - JPEG (compressed : 1) (0x4745504a) Oct 13 11:34:10 fox motion: [1] [NTC] [VID] v4l2_set_pix_format Selected palette JPEG Oct 13 11:34:10 fox motion: [1] [NTC] [VID] v4l2_do_set_pix_format: Testing palette JPEG (320x240) Oct 13 11:34:10 fox motion: [1] [NTC] [VID] v4l2_do_set_pix_format: Using palette JPEG (320x240) bytesperlines 320 sizeimage 29390 colorspace 00000007 Oct 13 11:34:10 fox motion: [1] [NTC] [VID] v4l2_scan_controls: found control 0x00980900, "Brightness", range 0,255 Oct 13 11:34:10 fox motion: [1] [NTC] [VID] v4l2_scan_controls: ^I"Brightness", default 128, current 14 Oct 13 11:34:10 fox motion: [1] [NTC] [VID] v4l2_scan_controls: found control 0x00980901, "Contrast", range 0,255 Oct 13 11:34:10 fox motion: [1] [NTC] [VID] v4l2_scan_controls: ^I"Contrast", default 128, current 128 Oct 13 11:34:10 fox motion: [1] [NTC] [VID] v4l2_scan_controls: found control 0x00980910, "Gamma", range 1,6 Oct 13 11:34:10 fox motion: [1] [NTC] [VID] v4l2_scan_controls: ^I"Gamma", default 4, current 4 Oct 13 11:34:10 fox motion: [1] [NTC] [VID] v4l2_scan_controls: found control 0x00980911, "Exposure", range 781,18750 Oct 13 11:34:10 fox motion: [1] [NTC] [VID] v4l2_scan_controls: ^I"Exposure", default 2343, current 2343 Oct 13 11:34:10 fox motion: [1] [NTC] [VID] v4l2_scan_controls: found control 0x00980912, "Gain, Automatic", range 0,1 Oct 13 11:34:10 fox motion: [1] [NTC] [VID] v4l2_scan_controls: ^I"Gain, Automatic", default 1, current 1 Oct 13 11:34:12 fox motion: [1] [NTC] [VID] vid_v4lx_start: Using V4L2 Oct 13 11:34:12 fox motion: [1] [NTC] [VID] v4l2_set_control: setting control "Brightness" to 14 (ret 0 ) Oct 13 11:34:12 fox motion: [1] [ERR] [ALL] motion_loop: Video device fatal error - Closing video device Oct 13 11:34:12 fox motion: [1] [NTC] [VID] vid_close: Closing video device /dev/video0 Oct 13 11:34:20 fox motion: [1] [WRN] [ALL] motion_loop: Retrying until successful connection with camera Oct 13 11:34:20 fox motion: [1] [NTC] [VID] vid_v4lx_start: Using videodevice /dev/video0 and input -1 Oct 13 11:34:20 fox motion: [1] [NTC] [VID] v4l2_get_capability: ------------------------ cap.driver: "gspca_zc3xx" cap.card: "USB Camera (046d:08d9)" cap.bus_info: "usb-0000:00:1d.2-1" cap.capabilities=0x85000001 ------------------------ Oct 13 11:34:20 fox motion: [1] [NTC] [VID] v4l2_get_capability: - VIDEO_CAPTURE Oct 13 11:34:20 fox motion: [1] [NTC] [VID] v4l2_get_capability: - READWRITE Oct 13 11:34:20 fox motion: [1] [NTC] [VID] v4l2_get_capability: - STREAMING Oct 13 11:34:20 fox motion: [1] [NTC] [VID] v4l2_select_input: name = "gspca_zc3xx", type 0x00000002, status 00000000 Oct 13 11:34:20 fox motion: [1] [NTC] [VID] v4l2_select_input: - CAMERA Oct 13 11:34:20 fox motion: [1] [WRN] [VID] v4l2_select_input: Device doesn't support VIDIOC_G_STD Oct 13 11:34:20 fox motion: [1] [NTC] [VID] v4l2_set_pix_format: Config palette index 17 (YU12) doesn't work. Oct 13 11:34:20 fox motion: [1] [NTC] [VID] v4l2_set_pix_format: Supported palettes: Oct 13 11:34:20 fox motion: [1] [NTC] [VID] v4l2_set_pix_format: (0) JPEG (JPEG) Oct 13 11:34:20 fox motion: [1] [NTC] [VID] v4l2_set_pix_format: 0 - JPEG (compressed : 1) (0x4745504a) Oct 13 11:34:20 fox motion: [1] [NTC] [VID] v4l2_set_pix_format Selected palette JPEG Oct 13 11:34:20 fox motion: [1] [NTC] [VID] v4l2_do_set_pix_format: Testing palette JPEG (320x240) Oct 13 11:34:20 fox motion: [1] [NTC] [VID] v4l2_do_set_pix_format: Using palette JPEG (320x240) bytesperlines 320 sizeimage 29390 colorspace 00000007 Oct 13 11:34:20 fox motion: [1] [NTC] [VID] v4l2_scan_controls: found control 0x00980900, "Brightness", range 0,255 Oct 13 11:34:20 fox motion: [1] [NTC] [VID] v4l2_scan_controls: ^I"Brightness", default 128, current 14 Oct 13 11:34:20 fox motion: [1] [NTC] [VID] v4l2_scan_controls: found control 0x00980901, "Contrast", range 0, Oct 13 11:34:20 fox motion: [1] [NTC] [VID] v4l2_scan_controls: ^I"Contrast", default 128, current 128 Oct 13 11:34:20 fox motion: [1] [NTC] [VID] v4l2_scan_controls: found control 0x00980910, "Gamma", range 1,6 Oct 13 11:34:20 fox motion: [1] [NTC] [VID] v4l2_scan_controls: ^I"Gamma", default 4, current 4 Oct 13 11:34:20 fox motion: [1] [NTC] [VID] v4l2_scan_controls: found control 0x00980911, "Exposure", range 781,18750 Oct 13 11:34:20 fox motion: [1] [NTC] [VID] v4l2_scan_controls: ^I"Exposure", default 2343, current 2343 Oct 13 11:34:20 fox motion: [1] [NTC] [VID] v4l2_scan_controls: found control 0x00980912, "Gain, Automatic", range 0,1 Oct 13 11:34:20 fox motion: [1] [NTC] [VID] v4l2_scan_controls: ^I"Gain, Automatic", default 1, current 1 Oct 13 11:34:22 fox motion: [1] [NTC] [VID] vid_v4lx_start: Using V4L2 Oct 13 11:34:22 fox motion: [1] [NTC] [VID] v4l2_set_control: setting control "Brightness" to 14 (ret 0 ) Oct 13 11:34:22 fox motion: [1] [ERR] [ALL] motion_loop: Video device fatal error - Closing video device Oct 13 11:34:22 fox motion: [1] [NTC] [VID] vid_close: Closing video device /dev/video0 Oct 13 11:34:30 fox motion: [1] [WRN] [ALL] motion_loop: Retrying until successful connection with camera Oct 13 11:34:30 fox motion: [1] [NTC] [VID] vid_v4lx_start: Using videodevice /dev/video0 and input -1 Oct 13 11:34:30 fox motion: [1] [NTC] [VID] v4l2_get_capability: ------------------------ cap.driver: "gspca_zc3xx" cap.card: "USB Camera (046d:08d9)" cap.bus_info: "usb-0000:00:1d.2-1" cap.capabilities=0x85000001 ------------------------ Oct 13 11:34:30 fox motion: [1] [NTC] [VID] v4l2_get_capability: - VIDEO_CAPTURE Oct 13 11:34:30 fox motion: [1] [NTC] [VID] v4l2_get_capability: - READWRITE Oct 13 11:34:30 fox motion: [1] [NTC] [VID] v4l2_get_capability: - STREAMING Oct 13 11:34:30 fox motion: [1] [NTC] [VID] v4l2_select_input: name = "gspca_zc3xx", type 0x00000002, status 00000000 Oct 13 11:34:30 fox motion: [1] [NTC] [VID] v4l2_select_input: - CAMERA Oct 13 11:34:30 fox motion: [1] [WRN] [VID] v4l2_select_input: Device doesn't support VIDIOC_G_STD Oct 13 11:34:30 fox motion: [1] [NTC] [VID] v4l2_set_pix_format: Config palette index 17 (YU12) doesn't work. Oct 13 11:34:30 fox motion: [1] [NTC] [VID] v4l2_set_pix_format: Supported palettes: Oct 13 11:34:30 fox motion: [1] [NTC] [VID] v4l2_set_pix_format: (0) JPEG (JPEG) Oct 13 11:34:30 fox motion: [1] [NTC] [VID] v4l2_set_pix_format: 0 - JPEG (compressed : 1) (0x4745504a) Oct 13 11:34:30 fox motion: [1] [NTC] [VID] v4l2_set_pix_format Selected palette JPEG Oct 13 11:34:30 fox motion: [1] [NTC] [VID] v4l2_do_set_pix_format: Testing palette JPEG (320x240) Oct 13 11:34:30 fox motion: [1] [NTC] [VID] v4l2_do_set_pix_format: Using palette JPEG (320x240) bytesperlines 320 sizeimage 29390 colorspace 00000007 Oct 13 11:34:30 fox motion: [1] [NTC] [VID] v4l2_scan_controls: found control 0x00980900, "Brightness", range 0,255 Oct 13 11:34:30 fox motion: [1] [NTC] [VID] v4l2_scan_controls: ^I"Brightness", default 128, current 14 Oct 13 11:34:30 fox motion: [1] [NTC] [VID] v4l2_scan_controls: found control 0x00980901, "Contrast", range 0,255 Oct 13 11:34:30 fox motion: [1] [NTC] [VID] v4l2_scan_controls: ^I"Contrast", default 128, current 128 Oct 13 11:34:30 fox motion: [1] [NTC] [VID] v4l2_scan_controls: found control 0x00980910, "Gamma", range 1,6 Oct 13 11:34:30 fox motion: [1] [NTC] [VID] v4l2_scan_controls: ^I"Gamma", default 4, current 4 Oct 13 11:34:30 fox motion: [1] [NTC] [VID] v4l2_scan_controls: found control 0x00980911, "Exposure", range 781,18750 Oct 13 11:34:30 fox motion: [1] [NTC] [VID] v4l2_scan_controls: ^I"Exposure", default 2343, current 2343 Oct 13 11:34:30 fox motion: [1] [NTC] [VID] v4l2_scan_controls: found control 0x00980912, "Gain, Automatic", range 0,1 Oct 13 11:34:30 fox motion: [1] [NTC] [VID] v4l2_scan_controls: ^I"Gain, Automatic", default 1, current 1 Oct 13 11:34:32 fox motion: [1] [NTC] [VID] vid_v4lx_start: Using V4L2 Oct 13 11:34:32 fox motion: [1] [NTC] [VID] v4l2_set_control: setting control "Brightness" to 14 (ret 0 ) Oct 13 11:34:32 fox motion: [1] [ERR] [ALL] motion_loop: Video device fatal error - Closing video device Oct 13 11:34:32 fox motion: [1] [NTC] [VID] vid_close: Closing video device /dev/video0 Oct 13 11:34:33 fox motion: [1] [NTC] [ALL] motion_loop: Video signal lost - Adding grey image Oct 13 11:34:40 fox motion: [1] [WRN] [ALL] motion_loop: Retrying until successful connection with camera Oct 13 11:34:40 fox motion: [1] [NTC] [VID] vid_v4lx_start: Using videodevice /dev/video0 and input -1 Oct 13 11:34:40 fox motion: [1] [NTC] [VID] v4l2_get_capability: ------------------------ cap.driver: "gspca_zc3xx" cap.card: "USB Camera (046d:08d9)" cap.bus_info: "usb-0000:00:1d.2-1" cap.capabilities=0x85000001 ------------------------ Oct 13 11:34:40 fox motion: [1] [NTC] [VID] v4l2_get_capability: - VIDEO_CAPTURE Oct 13 11:34:40 fox motion: [1] [NTC] [VID] v4l2_get_capability: - READWRITE Oct 13 11:34:40 fox motion: [1] [NTC] [VID] v4l2_get_capability: - STREAMING Oct 13 11:34:40 fox motion: [1] [NTC] [VID] v4l2_select_input: name = "gspca_zc3xx", type 0x00000002, status 00000000 Oct 13 11:34:40 fox motion: [1] [NTC] [VID] v4l2_select_input: - CAMERA Oct 13 11:34:40 fox motion: [1] [WRN] [VID] v4l2_select_input: Device doesn't support VIDIOC_G_STD Oct 13 11:34:40 fox motion: [1] [NTC] [VID] v4l2_set_pix_format: Config palette index 17 (YU12) doesn't work. Oct 13 11:34:40 fox motion: [1] [NTC] [VID] v4l2_set_pix_format: Supported palettes: Oct 13 11:34:40 fox motion: [1] [NTC] [VID] v4l2_set_pix_format: (0) JPEG (JPEG) Oct 13 11:34:40 fox motion: [1] [NTC] [VID] v4l2_set_pix_format: 0 - JPEG (compressed : 1) (0x4745504a) Oct 13 11:34:40 fox motion: [1] [NTC] [VID] v4l2_set_pix_format Selected palette JPEG Oct 13 11:34:40 fox motion: [1] [NTC] [VID] v4l2_do_set_pix_format: Testing palette JPEG (320x240) Oct 13 11:34:40 fox motion: [1] [NTC] [VID] v4l2_do_set_pix_format: Using palette JPEG (320x240) bytesperlines 320 sizeimage 29390 colorspace 00000007 Oct 13 11:34:40 fox motion: [1] [NTC] [VID] v4l2_scan_controls: found control 0x00980900, "Brightness", range 0,255 Oct 13 11:34:40 fox motion: [1] [NTC] [VID] v4l2_scan_controls: ^I"Brightness", default 128, current 14 Oct 13 11:34:40 fox motion: [1] [NTC] [VID] v4l2_scan_controls: found control 0x00980901, "Contrast", range 0,255 Oct 13 11:34:40 fox motion: [1] [NTC] [VID] v4l2_scan_controls: ^I"Contrast", default 128, current 128 Oct 13 11:34:40 fox motion: [1] [NTC] [VID] v4l2_scan_controls: found control 0x00980910, "Gamma", range 1,6 Oct 13 11:34:40 fox motion: [1] [NTC] [VID] v4l2_scan_controls: ^I"Gamma", default 4, current 4 Oct 13 11:34:40 fox motion: [1] [NTC] [VID] v4l2_scan_controls: found control 0x00980911, "Exposure", range 781,18750 Oct 13 11:34:40 fox motion: [1] [NTC] [VID] v4l2_scan_controls: ^I"Exposure", default 2343, current 2343 Oct 13 11:34:40 fox motion: [1] [NTC] [VID] v4l2_scan_controls: found control 0x00980912, "Gain, Automatic", range 0,1 Oct 13 11:34:40 fox motion: [1] [NTC] [VID] v4l2_scan_controls: ^I"Gain, Automatic", default 1, current 1 Oct 13 11:34:42 fox motion: [1] [NTC] [VID] vid_v4lx_start: Using V4L2 Oct 13 11:34:42 fox motion: [1] [NTC] [VID] v4l2_set_control: setting control "Brightness" to 14 (ret 0 ) Oct 13 11:34:42 fox motion: [1] [ERR] [ALL] motion_loop: Video device fatal error - Closing video device Oct 13 11:34:42 fox motion: [1] [NTC] [VID] vid_close: Closing video device /dev/video0 Oct 13 11:34:50 fox motion: [1] [WRN] [ALL] motion_loop: Retrying until successful connection with camera Oct 13 11:34:50 fox motion: [1] [NTC] [VID] vid_v4lx_start: Using videodevice /dev/video0 and input -1 Oct 13 11:34:50 fox motion: [1] [NTC] [VID] v4l2_get_capability: ------------------------ cap.driver: "gspca_zc3xx" cap.card: "USB Camera (046d:08d9)" cap.bus_info: "usb-0000:00:1d.2-1" cap.capabilities=0x85000001 ------------------------ Oct 13 11:34:50 fox motion: [1] [NTC] [VID] v4l2_get_capability: - VIDEO_CAPTURE Oct 13 11:34:50 fox motion: [1] [NTC] [VID] v4l2_get_capability: - READWRITE Oct 13 11:34:50 fox motion: [1] [NTC] [VID] v4l2_get_capability: - STREAMING Oct 13 11:34:50 fox motion: [1] [NTC] [VID] v4l2_select_input: name = "gspca_zc3xx", type 0x00000002, status 00000000 Oct 13 11:34:50 fox motion: [1] [NTC] [VID] v4l2_select_input: - CAMERA Oct 13 11:34:50 fox motion: [1] [WRN] [VID] v4l2_select_input: Device doesn't support VIDIOC_G_STD Oct 13 11:34:50 fox motion: [1] [NTC] [VID] v4l2_set_pix_format: Config palette index 17 (YU12) doesn't work. Oct 13 11:34:50 fox motion: [1] [NTC] [VID] v4l2_set_pix_format: Supported palettes: Oct 13 11:34:50 fox motion: [1] [NTC] [VID] v4l2_set_pix_format: (0) JPEG (JPEG) Oct 13 11:34:50 fox motion: [1] [NTC] [VID] v4l2_set_pix_format: 0 - JPEG (compressed : 1) (0x4745504a) Oct 13 11:34:50 fox motion: [1] [NTC] [VID] v4l2_set_pix_format Selected palette JPEG Oct 13 11:34:50 fox motion: [1] [NTC] [VID] v4l2_do_set_pix_format: Testing palette JPEG (320x240) Oct 13 11:34:50 fox motion: [1] [NTC] [VID] v4l2_do_set_pix_format: Using palette JPEG (320x240) bytesperlines 320 sizeimage 29390 colorspace 00000007 Oct 13 11:34:50 fox motion: [1] [NTC] [VID] v4l2_scan_controls: found control 0x00980900, "Brightness", range 0,255 Oct 13 11:34:50 fox motion: [1] [NTC] [VID] v4l2_scan_controls: ^I"Brightness", default 128, current 14 Oct 13 11:34:50 fox motion: [1] [NTC] [VID] v4l2_scan_controls: found control 0x00980901, "Contrast", range 0,255 Oct 13 11:34:50 fox motion: [1] [NTC] [VID] v4l2_scan_controls: ^I"Contrast", default 128, current 128 Oct 13 11:34:50 fox motion: [1] [NTC] [VID] v4l2_scan_controls: found control 0x00980910, "Gamma", range 1,6 Oct 13 11:34:50 fox motion: [1] [NTC] [VID] v4l2_scan_controls: ^I"Gamma", default 4, current 4 Oct 13 11:34:50 fox motion: [1] [NTC] [VID] v4l2_scan_controls: found control 0x00980911, "Exposure", range 781,18750 Oct 13 11:34:50 fox motion: [1] [NTC] [VID] v4l2_scan_controls: ^I"Exposure", default 2343, current 2343 Oct 13 11:34:50 fox motion: [1] [NTC] [VID] v4l2_scan_controls: found control 0x00980912, "Gain, Automatic", range 0,1 Oct 13 11:34:50 fox motion: [1] [NTC] [VID] v4l2_scan_controls: ^I"Gain, Automatic", default 1, current 1 Oct 13 11:34:52 fox motion: [1] [NTC] [VID] vid_v4lx_start: Using V4L2 Oct 13 11:34:52 fox motion: [1] [NTC] [VID] v4l2_set_control: setting control "Brightness" to 14 (ret 0 ) Oct 13 11:34:52 fox motion: [1] [ERR] [ALL] motion_loop: Video device fatal error - Closing video device Oct 13 11:34:52 fox motion: [1] [NTC] [VID] vid_close: Closing video device /dev/video0 Oct 13 11:35:00 fox motion: [1] [WRN] [ALL] motion_loop: Retrying until successful connection with camera Oct 13 11:35:00 fox motion: [1] [NTC] [VID] vid_v4lx_start: Using videodevice /dev/video0 and input -1 Oct 13 11:35:00 fox motion: [1] [NTC] [VID] v4l2_get_capability: ------------------------ cap.driver: "gspca_zc3xx" cap.card: "USB Camera (046d:08d9)" cap.bus_info: "usb-0000:00:1d.2-1" cap.capabilities=0x85000001 ------------------------ Oct 13 11:35:00 fox motion: [1] [NTC] [VID] v4l2_get_capability: - VIDEO_CAPTURE Oct 13 11:35:00 fox motion: [1] [NTC] [VID] v4l2_get_capability: - READWRITE Oct 13 11:35:00 fox motion: [1] [NTC] [VID] v4l2_get_capability: - STREAMING Oct 13 11:35:00 fox motion: [1] [NTC] [VID] v4l2_select_input: name = "gspca_zc3xx", type 0x00000002, status 000000 Oct 13 11:35:00 fox motion: [1] [NTC] [VID] v4l2_select_input: - CAMERA Oct 13 11:35:00 fox motion: [1] [WRN] [VID] v4l2_select_input: Device doesn't support VIDIOC_G_STD Oct 13 11:35:00 fox motion: [1] [NTC] [VID] v4l2_set_pix_format: Config palette index 17 (YU12) doesn't work. Oct 13 11:35:00 fox motion: [1] [NTC] [VID] v4l2_set_pix_format: Supported palettes: Oct 13 11:35:00 fox motion: [1] [NTC] [VID] v4l2_set_pix_format: (0) JPEG (JPEG) Oct 13 11:35:00 fox motion: [1] [NTC] [VID] v4l2_set_pix_format: 0 - JPEG (compressed : 1) (0x4745504a) Oct 13 11:35:00 fox motion: [1] [NTC] [VID] v4l2_set_pix_format Selected palette JPEG Oct 13 11:35:00 fox motion: [1] [NTC] [VID] v4l2_do_set_pix_format: Testing palette JPEG (320x240) Oct 13 11:35:00 fox motion: [1] [NTC] [VID] v4l2_do_set_pix_format: Using palette JPEG (320x240) bytesperlines 320 sizeimage 29390 colorspace 00000007 Oct 13 11:35:00 fox motion: [1] [NTC] [VID] v4l2_scan_controls: found control 0x00980900, "Brightness", range 0,255 Oct 13 11:35:00 fox motion: [1] [NTC] [VID] v4l2_scan_controls: ^I"Brightness", default 128, current 14 Oct 13 11:35:00 fox motion: [1] [NTC] [VID] v4l2_scan_controls: found control 0x00980901, "Contrast", range 0,255 Oct 13 11:35:00 fox motion: [1] [NTC] [VID] v4l2_scan_controls: ^I"Contrast", default 128, current 128 Oct 13 11:35:00 fox motion: [1] [NTC] [VID] v4l2_scan_controls: found control 0x00980910, "Gamma", range 1,6 Oct 13 11:35:00 fox motion: [1] [NTC] [VID] v4l2_scan_controls: ^I"Gamma", default 4, current 4 Oct 13 11:35:00 fox motion: [1] [NTC] [VID] v4l2_scan_controls: found control 0x00980911, "Exposure", range 781,18750 Oct 13 11:35:00 fox motion: [1] [NTC] [VID] v4l2_scan_controls: ^I"Exposure", default 2343, current 2343 Oct 13 11:35:00 fox motion: [1] [NTC] [VID] v4l2_scan_controls: found control 0x00980912, "Gain, Automatic", range 0,1 Oct 13 11:35:00 fox motion: [1] [NTC] [VID] v4l2_scan_controls: ^I"Gain, Automatic", default 1, current 1 Oct 13 11:35:02 fox motion: [1] [NTC] [VID] vid_v4lx_start: Using V4L2 Oct 13 11:35:02 fox motion: [1] [NTC] [VID] v4l2_set_control: setting control "Brightness" to 14 (ret 0 ) Oct 13 11:35:02 fox motion: [1] [ERR] [ALL] motion_loop: Video device fatal error - Closing video device Oct 13 11:35:02 fox motion: [1] [NTC] [VID] vid_close: Closing video device /dev/video0 Oct 13 11:35:10 fox motion: [1] [WRN] [ALL] motion_loop: Retrying until successful connection with camera Oct 13 11:35:10 fox motion: [1] [NTC] [VID] vid_v4lx_start: Using videodevice /dev/video0 and input -1 Oct 13 11:35:10 fox motion: [1] [NTC] [VID] v4l2_get_capability: ------------------------ cap.driver: "gspca_zc3xx" cap.card: "USB Camera (046d:08d9)" cap.bus_info: "usb-0000:00:1d.2-1" cap.capabilities=0x85000001 ------------------------ Oct 13 11:35:10 fox motion: [1] [NTC] [VID] v4l2_get_capability: - VIDEO_CAPTURE Oct 13 11:35:10 fox motion: [1] [NTC] [VID] v4l2_get_capability: - READWRITE Oct 13 11:35:10 fox motion: [1] [NTC] [VID] v4l2_get_capability: - STREAMING Oct 13 11:35:10 fox motion: [1] [NTC] [VID] v4l2_select_input: name = "gspca_zc3xx", type 0x00000002, status 00000000 Oct 13 11:35:10 fox motion: [1] [NTC] [VID] v4l2_select_input: - CAMERA Oct 13 11:35:10 fox motion: [1] [WRN] [VID] v4l2_select_input: Device doesn't support VIDIOC_G_STD Oct 13 11:35:10 fox motion: [1] [NTC] [VID] v4l2_set_pix_format: Config palette index 17 (YU12) doesn't work. Oct 13 11:35:10 fox motion: [1] [NTC] [VID] v4l2_set_pix_format: Supported palettes: Oct 13 11:35:10 fox motion: [1] [NTC] [VID] v4l2_set_pix_format: (0) JPEG (JPEG) Oct 13 11:35:10 fox motion: [1] [NTC] [VID] v4l2_set_pix_format: 0 - JPEG (compressed : 1) (0x4745504a) Oct 13 11:35:10 fox motion: [1] [NTC] [VID] v4l2_set_pix_format Selected palette JPEG Oct 13 11:35:10 fox motion: [1] [NTC] [VID] v4l2_do_set_pix_format: Testing palette JPEG (320x240) Oct 13 11:35:10 fox motion: [1] [NTC] [VID] v4l2_do_set_pix_format: Using palette JPEG (320x240) bytesperlines 320 sizeimage 29390 colorspace 00000007 Oct 13 11:35:10 fox motion: [1] [NTC] [VID] v4l2_scan_controls: found control 0x00980900, "Brightness", range 0,255 Oct 13 11:35:10 fox motion: [1] [NTC] [VID] v4l2_scan_controls: ^I"Brightness", default 128, current 14 Oct 13 11:35:10 fox motion: [1] [NTC] [VID] v4l2_scan_controls: found control 0x00980901, "Contrast", range 0,255 Oct 13 11:35:10 fox motion: [1] [NTC] [VID] v4l2_scan_controls: ^I"Contrast", default 128, current 128 Oct 13 11:35:10 fox motion: [1] [NTC] [VID] v4l2_scan_controls: found control 0x00980910, "Gamma", range 1,6 Oct 13 11:35:10 fox motion: [1] [NTC] [VID] v4l2_scan_controls: ^I"Gamma", default 4, current 4 Oct 13 11:35:10 fox motion: [1] [NTC] [VID] v4l2_scan_controls: found control 0x00980911, "Exposure", range 781,18750 Oct 13 11:35:10 fox motion: [1] [NTC] [VID] v4l2_scan_controls: ^I"Exposure", default 2343, current 2343 Oct 13 11:35:10 fox motion: [1] [NTC] [VID] v4l2_scan_controls: found control 0x00980912, "Gain, Automatic", range 0,1 Oct 13 11:35:10 fox motion: [1] [NTC] [VID] v4l2_scan_controls: ^I"Gain, Automatic", default 1, current 1 Oct 13 11:35:12 fox motion: [1] [NTC] [VID] vid_v4lx_start: Using V4L2 Oct 13 11:35:12 fox motion: [1] [NTC] [VID] v4l2_set_control: setting control "Brightness" to 14 (ret 0 ) Oct 13 11:35:12 fox motion: [1] [ERR] [ALL] motion_loop: Video device fatal error - Closing video device Oct 13 11:35:12 fox motion: [1] [NTC] [VID] vid_close: Closing video device /dev/video0 Oct 13 11:35:20 fox motion: [1] [WRN] [ALL] motion_loop: Retrying until successful connection with camera Oct 13 11:35:20 fox motion: [1] [NTC] [VID] vid_v4lx_start: Using videodevice /dev/video0 and input -1 Oct 13 11:35:20 fox motion: [1] [NTC] [VID] v4l2_get_capability: ------------------------ cap.driver: "gspca_zc3xx" cap.card: "USB Camera (046d:08d9)" cap.bus_info: "usb-0000:00:1d.2-1" cap.capabilities=0x85000001 ------------------------ Oct 13 11:35:20 fox motion: [1] [NTC] [VID] v4l2_get_capability: - VIDEO_CAPTURE Oct 13 11:35:20 fox motion: [1] [NTC] [VID] v4l2_get_capability: - READWRITE Oct 13 11:35:20 fox motion: [1] [NTC] [VID] v4l2_get_capability: - STREAMING Oct 13 11:35:20 fox motion: [1] [NTC] [VID] v4l2_select_input: name = "gspca_zc3xx", type 0x00000002, status 00000000 Oct 13 11:35:20 fox motion: [1] [NTC] [VID] v4l2_select_input: - CAMERA Oct 13 11:35:20 fox motion: [1] [WRN] [VID] v4l2_select_input: Device doesn't support VIDIOC_G_STD Oct 13 11:35:20 fox motion: [1] [NTC] [VID] v4l2_set_pix_format: Config palette index 17 (YU12) doesn't work. Oct 13 11:35:20 fox motion: [1] [NTC] [VID] v4l2_set_pix_format: Supported palettes: Oct 13 11:35:20 fox motion: [1] [NTC] [VID] v4l2_set_pix_format: (0) JPEG (JPEG) Oct 13 11:35:20 fox motion: [1] [NTC] [VID] v4l2_set_pix_format: 0 - JPEG (compressed : 1) (0x4745504a) Oct 13 11:35:20 fox motion: [1] [NTC] [VID] v4l2_set_pix_format Selected palette JPEG Oct 13 11:35:20 fox motion: [1] [NTC] [VID] v4l2_do_set_pix_format: Testing palette JPEG (320x240) Oct 13 11:35:20 fox motion: [1] [NTC] [VID] v4l2_do_set_pix_format: Using palette JPEG (320x240) bytesperlines 320 sizeimage 29390 colorspace 00000007 Oct 13 11:35:20 fox motion: [1] [NTC] [VID] v4l2_scan_controls: found control 0x00980900, "Brightness", range 0,255 Oct 13 11:35:20 fox motion: [1] [NTC] [VID] v4l2_scan_controls: ^I"Brightness", default 128, current 14 Oct 13 11:35:20 fox motion: [1] [NTC] [VID] v4l2_scan_controls: found control 0x00980901, "Contrast", range 0,255 Oct 13 11:35:20 fox motion: [1] [NTC] [VID] v4l2_scan_controls: ^I"Contrast", default 128, current 128 Oct 13 11:35:20 fox motion: [1] [NTC] [VID] v4l2_scan_controls: found control 0x00980910, "Gamma", range 1,6 Oct 13 11:35:20 fox motion: [1] [NTC] [VID] v4l2_scan_controls: ^I"Gamma", default 4, current 4 Oct 13 11:35:20 fox motion: [1] [NTC] [VID] v4l2_scan_controls: found control 0x00980911, "Exposure", range 781,18750 Oct 13 11:35:20 fox motion: [1] [NTC] [VID] v4l2_scan_controls: ^I"Exposure", default 2343, current 2343 Oct 13 11:35:20 fox motion: [1] [NTC] [VID] v4l2_scan_controls: found control 0x00980912, "Gain, Automatic", range 0,1 Oct 13 11:35:20 fox motion: [1] [NTC] [VID] v4l2_scan_controls: ^I"Gain, Automatic", default 1, current 1 Oct 13 11:35:22 fox motion: [1] [NTC] [VID] vid_v4lx_start: Using V4L2 Oct 13 11:35:22 fox motion: [1] [NTC] [VID] v4l2_set_control: setting control "Brightness" to 14 (ret 0 ) Oct 13 11:35:22 fox motion: [1] [ERR] [ALL] motion_loop: Video device fatal error - Closing video device Oct 13 11:35:22 fox motion: [1] [NTC] [VID] vid_close: Closing video device /dev/video0 ------- Oct 13 11:35:30 fox motion: [1] [NTC] [VID] v4l2_get_capability: - VIDEO_CAPTURE Oct 13 11:35:30 fox motion: [1] [NTC] [VID] v4l2_get_capability: - READWRITE Oct 13 11:35:30 fox motion: [1] [NTC] [VID] v4l2_get_capability: - STREAMING Oct 13 11:35:30 fox motion: [1] [NTC] [VID] v4l2_select_input: name = "gspca_zc3xx", type 0x00000002, status 00000000 Oct 13 11:35:30 fox motion: [1] [NTC] [VID] v4l2_select_input: - CAMERA Oct 13 11:35:30 fox motion: [1] [WRN] [VID] v4l2_select_input: Device doesn't support VIDIOC_G_STD Oct 13 11:35:30 fox motion: [1] [NTC] [VID] v4l2_set_pix_format: Config palette index 17 (YU12) doesn't work. Oct 13 11:35:30 fox motion: [1] [NTC] [VID] v4l2_set_pix_format: Supported palettes: Oct 13 11:35:30 fox motion: [1] [NTC] [VID] v4l2_set_pix_format: (0) JPEG (JPEG) Oct 13 11:35:30 fox motion: [1] [NTC] [VID] v4l2_set_pix_format: 0 - JPEG (compressed : 1) (0x4745504a) Oct 13 11:35:30 fox motion: [1] [NTC] [VID] v4l2_set_pix_format Selected palette JPEG Oct 13 11:35:30 fox motion: [1] [NTC] [VID] v4l2_do_set_pix_format: Testing palette JPEG (320x240) Oct 13 11:35:30 fox motion: [1] [NTC] [VID] v4l2_do_set_pix_format: Using palette JPEG (320x240) bytesperlines 320 sizeimage 29390 colorspace 00000007 Oct 13 11:35:30 fox motion: [1] [NTC] [VID] v4l2_scan_controls: found control 0x00980900, "Brightness", range 0,255 Oct 13 11:35:30 fox motion: [1] [NTC] [VID] v4l2_scan_controls: ^I"Brightness", default 128, current 14 Oct 13 11:35:30 fox motion: [1] [NTC] [VID] v4l2_scan_controls: found control 0x00980901, "Contrast", range 0,255 Oct 13 11:35:30 fox motion: [1] [NTC] [VID] v4l2_scan_controls: ^I"Contrast", default 128, current 128 Oct 13 11:35:30 fox motion: [1] [NTC] [VID] v4l2_scan_controls: found control 0x00980910, "Gamma", range 1,6 Oct 13 11:35:30 fox motion: [1] [NTC] [VID] v4l2_scan_controls: ^I"Gamma", default 4, current 4 Oct 13 11:35:30 fox motion: [1] [NTC] [VID] v4l2_scan_controls: found control 0x00980911, "Exposure", range 781,18750 Oct 13 11:35:30 fox motion: [1] [NTC] [VID] v4l2_scan_controls: ^I"Exposure", default 2343, current 2343 Oct 13 11:35:30 fox motion: [1] [NTC] [VID] v4l2_scan_controls: found control 0x00980912, "Gain, Automatic", range 0,1 Oct 13 11:35:30 fox motion: [1] [NTC] [VID] v4l2_scan_controls: ^I"Gain, Automatic", default 1, current 1 Oct 13 11:35:32 fox motion: [1] [NTC] [VID] vid_v4lx_start: Using V4L2 Oct 13 11:35:32 fox motion: [1] [NTC] [VID] v4l2_set_control: setting control "Brightness" to 14 (ret 0 ) Oct 13 11:35:32 fox motion: [1] [ERR] [ALL] motion_loop: Video device fatal error - Closing video device Oct 13 11:35:32 fox motion: [1] [NTC] [VID] vid_close: Closing video device /dev/video0 Oct 13 11:35:40 fox motion: [1] [WRN] [ALL] motion_loop: Retrying until successful connection with camera |