From: Gregg L. <gr...@li...> - 2008-12-22 20:14:17
|
John R. wrote: > Gregg Liming wrote: >> Hi John, >> >> John R. wrote: > >> Nope. You must select "closet_button_B" and perform sync links. The >> selection is always the controller. Technically, you would want to sync >> links on both day_scene and closet_button_B since both are controllers >> in your above example. > > Got it. In my case just did a sync links with both closet_button_B and > bathroom_scene. > >>> This command will create new links for any newly defined devices and >>> otherwise just update the scene link parameters (e.g., on-level and >>> ramp-rate). Because this method is far simpler to implement than the >>> manual method, it is recommended. >>> >>> It is not clear how in this process there is an association between the >>> scene and the button (log below from button press). >> There isn't as you didn't select the right controller. So, pick >> "closet_button_B" and try sync links again. > > OK. > >> If you want validation that the correct links are created after doing >> your sync links again, then take a look at "log links" for both the >> $closet (you must always select the "root" or group 01 device) and >> hall_light. You should see applicable controller links (in $closet) and >> responder links (in $hall_light). If confused, then post the output of >> log_links. > > After the sync links, closet_button_B tuns on hall_light, but it does it > at 100% immediately (not per the scene). uhhh... no. Per your previous email, you had: SCENE_MEMBER, hall_light, closet_button_B, 100%, 0.1s ... which isn't listed below, but is the relevant entry. Note that this declaration makes closet_button_B become the controller and hall_light be the responder. You specified 0.1s--which is "immediately". So, it's doing exactly as you asked it to do (albeit, not what you "wanted"). and .... [... snip ...] > Log links (hall): > > 12/22/08 01:59:14 PM menu_run: g=mh m=Insteon i=9 s=7 => action: hall > 'log links' > 12/22/08 01:59:14 PM Running: hall log links > 12/22/08 01:59:14 PM [Insteon_Device] link table for $hall (devcat: 0101): > 12/22/08 01:59:14 PM [Insteon_Device] aldb 0937cf011 [0x0FE8] contlr(01) > record to $plm(01), (d1:ff, d2:1f, d3:00) > 12/22/08 01:59:14 PM [Insteon_Device] aldb 0937cf810 [0x0FC8] rspndr(01) > record to $plm(81): onlevel=25% and ramp=0.5s (d3:00) The following entry is the one. Note that it's ramp rate is 0.1s as you had specified. > 12/22/08 01:59:14 PM [Insteon_Device] aldb 0ae97e040 [0x0FF8] rspndr(01) > record to $closet(04): onlevel=100% and ramp=0.1s (d3:00) > 12/22/08 01:59:14 PM [Insteon_Device] adlb [0x0FC0] is empty > 12/22/08 01:59:14 PM [Insteon_Device] adlb [0x0FD0] is empty > 12/22/08 01:59:14 PM [Insteon_Device] adlb [0x0FD8] is empty > 12/22/08 01:59:14 PM [Insteon_Device] adlb [0x0FE0] is empty > 12/22/08 01:59:14 PM [Insteon_Device] adlb [0x0FF0] is empty Gregg |