From: <br...@ha...> - 2007-12-07 15:54:52
|
Do you have any pictures of what you did? Thanks Brad > > > I did something similar for all of my doors. I drilled a very shallow > hole > in the end of my dead bolts and glued in a Radio Shack 64-1895 rare earth > magnet. The magnet uses a 3/16" hole and sticks by itself to the deadbolt > hole so the glue may not even be necessary. In fact, if you put the > magnet > in the hole for testing, it is very hard to get out. > > For the switch, I just used a magnetic reed switch in the deadbolt door > frame hole. The switch is shimmed to the proper distance from the magnet > when the dead bolt is engaged. You can get normally open or normally > closed > switches to suit your preference. Just be sure to get small enough > switches > to fit completely inside the dead bolt door frame hole. I don't recall > where I ordered mine. The ones from Radio Shack were too long. > > The installation was easy. I just carefully pried the trim off the inside > of the door frame and everything was accessible. I ran the wire inside > the > frame and drilled a hole directly down into the basement. Be sure to test > everything before you put the trim back on. > > > > -----Original Message----- > From: mis...@li... > [mailto:mis...@li...] On Behalf Of Jim > Serack > Sent: Monday, December 03, 2007 1:18 PM > To: 'The main list for the MisterHouse home automation program' > Subject: Re: [mh] I gots a new toy (Elk M1) > > I have deadbolts where the frame is not exposed. I have DS10A RF sensors > and > I have put a rare earth magnet in the brass handle of the inside deadbolt > - > when it is over a reed switch the bolt is engaged. This was particularly > useful where the two front doors lock together (one with top and bottom > pins) since wires are really asking for trouble. > > I also have made but currently don't use a metal locator coil behind the > deadbolt plate - in the frame - the coil is part of an oscillator circuit > whose frequency changes when the bolt is engaged (inside the coil). I'm a > fan of non-contact detecting of things like locks, door position, etc - I > think there is less likely hood of interfering with the lock function. > > Jim > > -----Original Message----- > From: mis...@li... > [mailto:mis...@li...] On Behalf Of MrT > Sent: December 3, 2007 12:57 PM > To: mis...@li... > Subject: Re: [mh] I gots a new toy (Elk M1) > > > > > > Ralph Mitchell wrote: >> >> On Dec 3, 2007 11:15 AM, MrT <tar...@ya...> wrote: >> ... would it be practical to embed a coil in the doorframe, ... There >> should be enough steel in the bolt to alter current flow in the coil >> and there'd be no switch to wear out. ... >> > That's a very interesting idea! I think putting it into practice will be > tricky. Installing a coil in the deadbolt pocket is not easy and the > deadbolt's movement can damage the windings. Some lock manufacturers > provide a plastic dust-jacket to fit within the pocket and improve its > appearance. Perhaps the coil could be wound around the dust-jacket. > > > I would not be overly concerned with a switch's reliability. Most > switches, > designed for alarm systems, are very reliable and work for years without > failure. > > > -- > View this message in context: > http://www.nabble.com/I-gots-a-new-toy-%28Elk-M1%29-tf4925988.html#a14134997 > Sent from the Misterhouse - User mailing list archive at Nabble.com. > > > ------------------------------------------------------------------------- > SF.Net email is sponsored by: The Future of Linux Business White Paper > from > Novell. From the desktop to the data center, Linux is going mainstream. > Let it simplify your IT future. > http://altfarm.mediaplex.com/ad/ck/8857-50307-18918-4 > ________________________________________________________ > To unsubscribe from this list, go to: > http://sourceforge.net/mail/?group_id=1365 > > ------------------------------------------------------------------------- > SF.Net email is sponsored by: The Future of Linux Business White Paper > from Novell. From the desktop to the data center, Linux is going > mainstream. Let it simplify your IT future. > http://altfarm.mediaplex.com/ad/ck/8857-50307-18918-4 > ________________________________________________________ > To unsubscribe from this list, go to: > http://sourceforge.net/mail/?group_id=1365 > > > > > ------------------------------------------------------------------------- > SF.Net email is sponsored by: > Check out the new SourceForge.net Marketplace. > It's the best place to buy or sell services for > just about anything Open Source. > http://sourceforge.net/services/buy/index.php > ________________________________________________________ > To unsubscribe from this list, go to: > http://sourceforge.net/mail/?group_id=1365 > > |