From: Thomas F. <th...@fj...> - 2011-05-12 16:17:57
|
On May 10, 2011, Thomas Fjellstrom wrote: > On May 8, 2011, Thomas Fjellstrom wrote: > > I seem to be able to record it well enough for my hauppage MCE > > transceiver to see the button presses via irw, but I can't seem to get > > it to send an ir signal that the pioneer reciever (its a VSX-462S, > > remote is a CU-VSX065) likes. The Pioneer won't accept any of the > > buttons I try to send via irsend. > > > > irrecord seems to have a really hard time trying to figure out the > > signal. After several tries, the following is the best config I've > > managed with raw mode. irw does see the button presses from the remote > > just fine, but I'm more interested in sending commands to the Pioneer > > than using its remote on my htpc. > > > > begin remote > > > > name reciever1 > > flags RAW_CODES > > eps 30 > > aeps 100 > > > > gap 39342 > > > > begin raw_codes > > > > name KEY_POWER > > > > 8600 7124 600 1550 600 450 > > > > 600 1500 600 450 600 450 > > 650 5494 600 450 600 4544 > > 600 450 600 4545 600 450 > > 550 4541 600 1500 600 500 > > 550 1550 600 450 600 500 > > 550 500 550 1550 600 4544 > > 550 1550 600 450 600 500 > > 550 500 550 1550 600 3544 > > 550 500 550 500 600 450 > > 600 5545 550 1550 550 26601 > > 550 20340 8550 7241 550 1550 > > 600 500 550 1550 550 500 > > 550 500 550 5596 550 500 > > 550 4589 500 550 500 4594 > > 550 500 550 4544 600 1550 > > 550 500 550 1600 500 550 > > 550 500 550 500 550 1600 > > 550 4544 550 1600 500 550 > > 550 500 550 550 500 1600 > > 550 3542 550 500 550 550 > > 500 550 500 5592 550 1600 > > 500 21594 550 > > > > name KEY_VOLUMEUP > > > > 8600 7123 600 1550 600 450 > > > > 600 1500 600 450 600 450 > > 600 4544 600 450 600 4541 > > 600 450 600 4500 600 450 > > 600 4543 600 1500 600 450 > > 600 1550 600 450 600 450 > > 600 4540 600 450 600 3492 > > 600 500 550 500 550 500 > > 600 450 600 1550 550 500 > > 600 1500 600 500 550 1550 > > 550 5545 600 1550 550 > > > > name KEY_VOLUMEDOWN > > > > 8550 8174 600 1500 600 450 > > > > 600 1500 650 450 600 450 > > 600 4489 600 450 600 4544 > > 600 450 600 5544 600 450 > > 600 4495 600 1550 600 450 > > 600 1500 600 500 550 1550 > > 600 4491 600 500 550 4540 > > 600 450 600 450 600 500 > > 550 500 600 450 600 450 > > 600 1550 550 500 550 1550 > > 600 5544 550 1550 600 27538 > > 550 19343 8500 8241 550 1550 > > 550 550 550 1550 550 500 > > 550 500 550 4592 550 500 > > 550 4593 550 500 550 5544 > > 550 500 550 4594 550 1550 > > 550 500 550 1600 550 500 > > 550 1600 500 4592 550 500 > > 550 4594 500 550 550 500 > > 550 500 550 550 500 550 > > 550 500 550 1550 550 500 > > 550 1600 550 6542 550 1600 > > 550 20543 550 > > > > end raw_codes > > > > end remote > > > > > > Is there anyway I can get ir blasting to work with my setup? > > > > Additional info: lsusb gives the following for my MCE transceiver > > Bus 003 Device 002: ID 1784:0001 TopSeed Technology Corp. eHome Infrared > > Transceiver > > > > Thanks. > > Any hints on how to get lirc to send a signal my receiver understands? > > The interesting thing is, `ir-keytable -t` doesn't seem to see any of the > events from the pioneer remote, but irw does. I'm stumped here. Is there a way I can get a MCE/eHome ir blaster to communicate with my Pioneer VSX-462S receiver? And some way to reliably record the remote that the receiver came with? irrecord has a tough time with it. -- Thomas Fjellstrom th...@fj... |