Re: I'm going nuts... simple question: are there variants of the PVR150 that do not work in linux??

[Andreas D. <an...@gm...>]

-> is it running with M$ Win ? if yes, 1) and 2) are out.
-> is it maybe /dev/input/event1 ? take out the card and see if it is no more 
available under lsinput
-> what says `cat /proc/bus/input/devices` ?
-> why you try lirc_kbd_i2c and not lirc_i2c ?
-> have you tried the steps  at 
http://www.mythtv.org/wiki/index.php/PVR150_Remote ?

Andreas

Am Freitag, 7. Dezember 2007 16:21 schrieb stuart:
> cw...@li... wrote:
> > stuart writes:
> >> I'm going nuts...  simple question: are there variants of the PVR150
> >> that do not work in linux??
> >> ...thanks
> >
> > The plave to ask this question is the ivtv mailing list...
> > http://ivtvdriver.org/
> > Regards,
> > Cecil
>
> Hey, thanks guys for your help.  Over at one of the ivtv list I ran
> across the command to list inputs:
> ---
> # lsinput
> /dev/input/event0
>     bustype : BUS_I8042
>     vendor  : 0x1
>     product : 0x1
>     version : 43841
>     name    : "AT Translated Set 2 keyboard"
>     phys    : "isa0060/serio0/input0"
>     bits ev : EV_SYN EV_KEY EV_MSC EV_LED EV_REP
>
> /dev/input/event1
>     bustype : BUS_USB
>     vendor  : 0x1241
>     product : 0x1166
>     version : 272
>     name    : "HID 1241:1166"
>     phys    : "usb-0000:00:03.1-1/input0"
>     uniq    : ""
>     bits ev : EV_SYN EV_KEY EV_REL
>
> /dev/input/event2
>     bustype : BUS_ISA
>     vendor  : 0x1f
>     product : 0x1
>     version : 256
>     name    : "PC Speaker"
>     phys    : "isa0061/input0"
>     bits ev : EV_SYN EV_SND
>
> /dev/input/event3
>     bustype : BUS_HOST
>     vendor  : 0x0
>     product : 0x2
>     version : 0
>     name    : "Power Button (FF)"
>     phys    : "button_power/button/input0"
>     bits ev : EV_SYN EV_KEY
>
> /dev/input/event4
>     bustype : BUS_HOST
>     vendor  : 0x0
>     product : 0x1
>     version : 0
>     name    : "Power Button (CM)"
>     phys    : "PNP0C0C/button/input0"
>     bits ev : EV_SYN EV_KEY
>
> /dev/input/event5
>     bustype : BUS_HOST
>     vendor  : 0x0
>     product : 0x3
>     version : 0
>     name    : "Sleep Button (CM)"
>     phys    : "PNP0C0E/button/input0"
>     bits ev : EV_SYN EV_KEY
> ---
>
> ...who's output was like a condensed version of the utility that
> Jonathan sent me, thanks Jonathan.
>
> As you can see - no Hauppauge card.  So I figure I have one of the
> following problems:
>
> 1) Broken hardware - hard to believe, the Hauppauge card has been
> working great recording shows for the past year.
>
> 2) Conflict between it and something else - there is a KWorld ATSC 110
> HDTV tuner card next to the Hauppauge.
>
> 3) I've configured / set up something wrong - humm, don't know about
> this one.  The ir_kbd_i2c module can not find the HW.  And utilities
> like irrecord say they can not initialize the hardware.
>
> My bet is it's 2 - but I know people with this setup (Haupauge PVR-150
> and KWorld ATSC 110).
>
>
> -------------------------------------------------------------------------
> SF.Net email is sponsored by:
> Check out the new SourceForge.net Marketplace.
> It's the best place to buy or sell services for
> just about anything Open Source.
> http://sourceforge.net/services/buy/index.php