Re: No response from irexec... maybe it's lircd ?

[Andreas D. <an...@gm...>]

your question is not too technical, but it's incomplete!

how do you run irrecord and what is the output of it?

did you tried the debug option of irrecord? (see somewhere at lirc.org)

remark: lircd and irrecord are independend, thus you must stop lircd to use 
irrecord... if you think your lircd.conf is ok, then you can try lircd and 
test with irw

Andreas

Am Freitag, 7. Dezember 2007 15:36 schrieb Junior:
> Is this the right list for this questions?
> Is it too technical for the list?
>
> > -----Original Message-----
> > From: ej...@in...
> > Sent: Thu, 6 Dec 2007 14:05:33 -0800
> > To: lir...@li...
> > Subject: No response from irexec... maybe it's lircd ?
> >
> > Hi,
> > I've written a new device driver for a serial IR interface.
> >
> > I've tested and verified that the driver works and got the pulse/space
> > timing ok.
> > I did a hexdump of /dev/lirc and also used mode 2 and see all the data.
> >
> > However, I'm unable to get anything out of lircd and irexec.
> >
> > My lircd.conf looks like this:
> >
> >  begin remote
> >     name HAI
> >     bits 24
> >     flags SPACE_ENC
> >     eps 30
> >     aeps    100
> >     header  9200    4500
> >     one     620     1600
> >     zero    620     520
> >     gap     16777215
> >     toggle_bit  0
> >         begin codes
> >             BUTT0   0x555810
> >             POWER   0x555820
> >             ENTER   0x555840
> >             OTHER   0x555850
> >             BUTT1   0x555860
> >             BUTT2   0x555870
> >             BUTT3   0x555880
> >             BUTT3   0x555890
> >             BUTT4   0x5558A0
> >         end codes
> > end remote
> >
> > I'm not sure about "gap" but this is essentially a PULSE_MASK.
> > Any bulse that is too large to be a valit timing, I send a PULSE_MASK
> > which is
> > pretty much a break or start of new data.
> > The driver is hardcoded into the kernel and I build lircd and others with
> > driver=userspace.
> > I think this should work but so far the daemon doesn't seem to be doing
> > anything. The daemon logfile however,
> > does show clients accepted and dropped accordingly.
> >
> > Can anyone help?
> >
> > Thanks,
> > --Jr.
> >
> > ____________________________________________________________
> > Receive Notifications of Incoming Messages
> > Easily monitor multiple email accounts & access them with a click.
> > Visit http://www.inbox.com/notifier and check it out!
> >
> > -------------------------------------------------------------------------
> > SF.Net email is sponsored by:
> > Check out the new SourceForge.net Marketplace.
> > It's the best place to buy or sell services for
> > just about anything Open Source.
> > http://sourceforge.net/services/buy/index.php
>
> ____________________________________________________________
> FREE 3D MARINE AQUARIUM SCREENSAVER - Watch dolphins, sharks & orcas on
> your desktop! Check it out at http://www.inbox.com/marineaquarium
>
> -------------------------------------------------------------------------
> SF.Net email is sponsored by:
> Check out the new SourceForge.net Marketplace.
> It's the best place to buy or sell services for
> just about anything Open Source.
> http://sourceforge.net/services/buy/index.php