|
From: Matthias M. <DJ...@gm...> - 2006-05-27 12:32:29
|
Hi, today I tried also again the 2.4.27 APUS Kernel from the debian page =20 but I got some problems. Look what the debug output reports: Searching for SAVEKMSG magic... Found 10527 bytes at 0x001e0010 >>>>>>>>>>>>>>>>>>>> Memory BAT mapping: BAT2=3D64Mb, BAT3=3D32Mb, residual: 31Mb Total memory =3D 127MB; using 256kB for hash table (at c0300000) Linux version 2.4.27-apus (sven@pegasos2) (version gcc 3.3.5 (Debian =20 1:3.3.5-8)) #2 sam f=E9v 26 13:19:51 CET 2005 Amiga hardware found: [A4000T] VIDEO BLITTER AUDIO FLOPPY A4000_SCSI =20 A4000_IDE KEYBOARD MOUSE SERIAL PARALLEL A3000_CLK CHIP_RAM PAULA =20 LISA ALICE_PAL ZORRO3 On node 0 totalpages: 32512 zone(0): 32512 pages. zone(1): 0 pages. zone(2): 0 pages. Kernel command line: root=3D/dev/sda4 init=3D/etc/init.rd =20 video=3Dpm2fb:mode:1280x1024-60 nobats -d debug=3Dmem APUS: BATs=3D0, BUS=3D60MHz, RAM=3D70ns, PCI bridge=3D1 time_init: decrementer frequency =3D 15.002690 MHz Console: colour dummy device 80x25 Calibrating delay loop... 179.81 BogoMIPS Memory: 125388k available (2012k kernel code, 704k data, 148k init, =20 0k highmem) Dentry cache hash table entries: 16384 (order: 5, 131072 bytes) Inode cache hash table entries: 8192 (order: 4, 65536 bytes) Mount cache hash table entries: 512 (order: 0, 4096 bytes) Buffer cache hash table entries: 4096 (order: 2, 16384 bytes) Page-cache hash table entries: 32768 (order: 5, 131072 bytes) POSIX conformance testing by UNIFIX Zorro: Probing AutoConfig expansion devices: 3 devices Linux NET4.0 for Linux 2.4 Based upon Swansea University Computer Society NET3.039 Initializing RT netlink socket Starting kswapd Journalled Block Device driver loaded devfs: v1.12c (20020818) Richard Gooch (rg...@at...) devfs: boot_options: 0x0 EFS: 1.0a - http://aeschi.ch.eu.org/efs/ parport_gvpio_init : found =3D 0 ioremap: fffc0000 (00001000) -> c801a000 ioremap: fffe0000 (00001000) -> c801c000 ioremap: e0000000 (00800000) -> c801e000 ioremap: ef010000 (00010000) -> c881f000 Console: switching to colour frame buffer device 160x64 fb0: CVisionPPC/BVisionPPC (Permedia2), using 8192K of video memory. fb1: Amiga AGA frame buffer device, using 1280K of video memory clgen: Driver for Cirrus Logic based graphic boards, v1.9.9.1 clgen: no supported board found. pty: 256 Unix98 ptys configured Commodore A2232 driver initializing. Total: 0 A2232 boards initialized. Amiga-builtin serial driver version 4.30 ttyS00 is the amiga builtin serial port Amiga mouse installed. Generic RTC Driver v1.07 FD: probing units found fd0 SLIP: version 0.8.4-NET3.019-NEWTTY (dynamic channels, max=3D256) (6 =20 bit encapsulation enabled). CSLIP: code copyright 1989 Regents of the University of California. SLIP linefill/keepalive option. RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize loop: loaded (max 8 devices) PPP generic driver version 2.4.2 PPP Deflate Compression module registered PPP BSD Compression module registered No Ariadne II or X-Surf ethernet card found. No Hydra ethernet card found. eth0: Ariadne at 0x00e90000, Ethernet Address 00:60:30:00:07:0b Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4 ide: Assuming 50MHz system bus speed for PIO modes; override with =20 idebus=3Dxx ide0: Gayle IDE interface (A4000 style) Probing IDE interface ide0... ide0: Wait for ready failed before probe ! SCSI subsystem driver Revision: 1.00 scsi-ncr53c7xx : NCR53c710 at memory 0x80dd0040, io 0x0, irq 12 scsi0: Revision 0x1 scsi0 : NCR code relocated to 0xfe9a5e8 (virt 0xc7e9a5e8) scsi0 : test 1 started scsi0 : Amiga NCR53c710 SCSI scsi0 : target 1 accepting period 200ns offset 8 5.00MHz synchronous =20 SCSI scsi0 : setting target 1 to period 200ns offset 8 5.00MHz synchronous =20= SCSI Vendor: PLEXTOR Model: CD-R PX-W1210S Rev: 1.01 Type: CD-ROM ANSI SCSI revision: 02 ncr53c8xx: 53c770 detected ncr53c770-0: rev=3D0x00, base=3D0xf40000, io_port=3D0x0, irq=3D12 ncr53c770-0: using memory mapped IO at virtual address 0x80f40000 ncr53c770-0: ID 7, Fast-20, Parity Checking ncr53c770-0: initial SCNTL3/DMODE/DCNTL/CTEST3/4/5 =3D (hex) 05/=20 c0/21/00/00/04 ncr53c770-0: final SCNTL3/DMODE/DCNTL/CTEST3/4/5 =3D (hex) 05/=20 c0/21/00/00/04 ncr53c770-0: on-chip RAM at 0xf41000 ncr53c770-0: resetting, command processing suspended for 2 seconds ncr53c770-0: restart (scsi reset). ncr53c770-0: enabling clock multiplier ncr53c770-0: Downloading SCSI SCRIPTS. scsi1 : ncr53c770-3.4.3-20010212 ncr53c770-0: command processing resumed Vendor: ST320082 Model: 2A Rev: 2.00 Type: Direct-Access ANSI SCSI revision: 02 Attached scsi disk sda at scsi1, channel 0, id 3, lun 0 ncr53c770-0-<3,*>: FAST-20 SCSI 20.0 MB/s (50 ns, offset 15) SCSI device sda: 268435456 512-byte hdwr sectors (137439 MB) Partition check: /dev/scsi/host1/bus0/target3/lun0:<6>ncr53c770-0-<3,0>: extended =20 error 15. ncr53c770-0-<3,0>: COMMAND FAILED (89 0) @c7e24000. ncr53c770-0-<3,0>: extended error 15. ncr53c770-0-<3,0>: COMMAND FAILED (89 0) @c7e24000. scsi1 channel 0 : resetting for second half of retries. SCSI bus is being reset for host 1 channel 0. ncr53c8xx_reset: pid=3D243 reset_flags=3D1 serial_number=3D0 =20 serial_number_at_timeout=3D0 ncr53c770-0: resetting, command processing suspended for 2 seconds scsi1: device driver called scsi_done() for a synchronous reset. ncr53c770-0: restart (scsi reset). ncr53c770-0: enabling clock multiplier ncr53c770-0: Downloading SCSI SCRIPTS. ncr53c770-0: command processing resumed ncr53c770-0-<3,*>: FAST-20 SCSI 20.0 MB/s (50 ns, offset 15) ncr53c770-0-<3,0>: extended error 15. ncr53c770-0-<3,0>: COMMAND FAILED (89 2) @c7e24000. ncr53c770-0-<3,0>: extended error 15. ncr53c770-0-<3,0>: COMMAND FAILED (89 0) @c7e24000. ncr53c770-0-<3,0>: extended error 15. ncr53c770-0-<3,0>: COMMAND FAILED (89 0) @c7e24000. SCSI disk error : host 1 channel 0 id 3 lun 0 return code =3D 27070000 I/O error: dev 08:00, sector 0 ncr53c770-0-<3,0>: extended error 15. ncr53c770-0-<3,0>: COMMAND FAILED (89 0) @c7e24000. ncr53c770-0-<3,0>: extended error 15. ncr53c770-0-<3,0>: COMMAND FAILED (89 0) @c7e24000. scsi1 channel 0 : resetting for second half of retries. SCSI bus is being reset for host 1 channel 0. ncr53c8xx_reset: pid=3D248 reset_flags=3D1 serial_number=3D0 =20 serial_number_at_timeout=3D0 ncr53c770-0: resetting, command processing suspended for 2 seconds scsi1: device driver called scsi_done() for a synchronous reset. ncr53c770-0: restart (scsi reset). ncr53c770-0: enabling clock multiplier ncr53c770-0: Downloading SCSI SCRIPTS. ncr53c770-0: command processing resumed ncr53c770-0-<3,*>: FAST-20 SCSI 20.0 MB/s (50 ns, offset 15) ncr53c770-0-<3,0>: extended error 15. ncr53c770-0-<3,0>: COMMAND FAILED (89 2) @c7e24000. ncr53c770-0-<3,0>: extended error 15. ncr53c770-0-<3,0>: COMMAND FAILED (89 0) @c7e24000. ncr53c770-0-<3,0>: extended error 15. ncr53c770-0-<3,0>: COMMAND FAILED (89 0) @c7e24000. SCSI disk error : host 1 channel 0 id 3 lun 0 return code =3D 27070000 I/O error: dev 08:00, sector 2 ncr53c770-0-<3,0>: extended error 15. ncr53c770-0-<3,0>: COMMAND FAILED (89 0) @c7e24000. ncr53c770-0-<3,0>: extended error 15. ncr53c770-0-<3,0>: COMMAND FAILED (89 0) @c7e24000. scsi1 channel 0 : resetting for second half of retries. SCSI bus is being reset for host 1 channel 0. ncr53c8xx_reset: pid=3D253 reset_flags=3D1 serial_number=3D0 =20 serial_number_at_timeout=3D0 ncr53c770-0: resetting, command processing suspended for 2 seconds scsi1: device driver called scsi_done() for a synchronous reset. ncr53c770-0: restart (scsi reset). ncr53c770-0: enabling clock multiplier ncr53c770-0: Downloading SCSI SCRIPTS. ncr53c770-0: command processing resumed ncr53c770-0-<3,*>: FAST-20 SCSI 20.0 MB/s (50 ns, offset 15) ncr53c770-0-<3,0>: extended error 15. ncr53c770-0-<3,0>: COMMAND FAILED (89 2) @c7e24000. ncr53c770-0-<3,0>: extended error 15. ncr53c770-0-<3,0>: COMMAND FAILED (89 0) @c7e24000. ncr53c770-0-<3,0>: extended error 15. ncr53c770-0-<3,0>: COMMAND FAILED (89 0) @c7e24000. SCSI disk error : host 1 channel 0 id 3 lun 0 return code =3D 27070000 I/O error: dev 08:00, sector 4 ncr53c770-0-<3,0>: extended error 15. ncr53c770-0-<3,0>: COMMAND FAILED (89 0) @c7e24000. ncr53c770-0-<3,0>: extended error 15. ncr53c770-0-<3,0>: COMMAND FAILED (89 0) @c7e24000. scsi1 channel 0 : resetting for second half of retries. SCSI bus is being reset for host 1 channel 0. ncr53c8xx_reset: pid=3D259 reset_flags=3D1 serial_number=3D0 =20 serial_number_at_timeout=3D0 ncr53c770-0: resetting, command processing suspended for 2 seconds scsi1: device driver called scsi_done() for a synchronous reset. ncr53c770-0: restart (scsi reset). ncr53c770-0: enabling clock multiplier ncr53c770-0: Downloading SCSI SCRIPTS. ncr53c770-0: command processing resumed ncr53c770-0-<3,*>: FAST-20 SCSI 20.0 MB/s (50 ns, offset 15) ncr53c770-0-<3,0>: extended error 15. ncr53c770-0-<3,0>: COMMAND FAILED (89 2) @c7e24000. ncr53c770-0-<3,0>: extended error 15. ncr53c770-0-<3,0>: COMMAND FAILED (89 0) @c7e24000. ncr53c770-0-<3,0>: extended error 15. ncr53c770-0-<3,0>: COMMAND FAILED (89 0) @c7e24000. SCSI disk error : host 1 channel 0 id 3 lun 0 return code =3D 27070000 I/O error: dev 08:00, sector 0 ncr53c770-0-<3,0>: extended error 15. ncr53c770-0-<3,0>: COMMAND FAILED (89 0) @c7e24000. ncr53c770-0-<3,0>: extended error 15. ncr53c770-0-<3,0>: COMMAND FAILED (89 0) @c7e24000. scsi1 channel 0 : resetting for second half of retries. SCSI bus is being reset for host 1 channel 0. ncr53c8xx_reset: pid=3D264 reset_flags=3D1 serial_number=3D0 =20 serial_number_at_timeout=3D0 ncr53c770-0: resetting, command processing suspended for 2 seconds scsi1: device driver called scsi_done() for a synchronous reset. ncr53c770-0: restart (scsi reset). ncr53c770-0: enabling clock multiplier ncr53c770-0: Downloading SCSI SCRIPTS. ncr53c770-0: command processing resumed ncr53c770-0-<3,*>: FAST-20 SCSI 20.0 MB/s (50 ns, offset 15) ncr53c770-0-<3,0>: extended error 15. ncr53c770-0-<3,0>: COMMAND FAILED (89 2) @c7e24000. ncr53c770-0-<3,0>: extended error 15. ncr53c770-0-<3,0>: COMMAND FAILED (89 0) @c7e24000. ncr53c770-0-<3,0>: extended error 15. ncr53c770-0-<3,0>: COMMAND FAILED (89 0) @c7e24000. SCSI disk error : host 1 channel 0 id 3 lun 0 return code =3D 27070000 I/O error: dev 08:00, sector 2 unable to read partition table Attached scsi CD-ROM sr0 at scsi0, channel 0, id 1, lun 0 sr0: scsi3-mmc drive: 32x/32x writer cd/rw xa/form2 cdda tray Uniform CD-ROM driver Revision: 3.12 NET4: Linux TCP/IP 1.0 for NET4.0 IP: routing cache hash table of 512 buckets, 4Kbytes TCP: Hash tables configured (established 8192 bind 16384) NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. VFS: Cannot open root device "sda4" or 08:04 Please append a correct "root=3D" boot option Kernel panic: VFS: Unable to mount root fs on 08:04 <0>Rebooting in 180 seconds..<<<<<<<<<<<<<<<<<<<< Anyone an idea? APUS Kernel 2.4.20 works without problems. |