From: Daniele P. <pe...@cs...> - 2002-11-13 10:03:15
|
Hans Neukomm wrote: > what is the meaning of - my dmesg: > > =========================================== > irda_init() > irlan_init() > irlan_register_netdev() > IrCOMM protocol (Dag Brattli) > smsc_ircc_init > smsc_superio_flat() > smsc_ircc_probe() > smsc_access() > smsc_superio_paged() > smsc_ircc_probe() > smsc_access() > smsc_superio_flat() > smsc_ircc_probe() > smsc_access() > smsc_superio_paged() > smsc_ircc_probe() > smsc_access() > smsc_superio_flat() > smsc_ircc_probe() > smsc_access() > smsc_superio_paged() > smsc_ircc_probe() > smsc_access() > smsc_superio_flat() > smsc_ircc_probe() > smsc_access() > smsc_access() > found SMC SuperIO Chip (devid=0x5a rev=00 base=0x002e): LPC47N227 > smsc_superio_flat(): IrDA not enabled This means your SuperIO chip is not initialized properly. Have your read toshsat1800-irdasetup README? > smsc_superio_flat(): fir: 0x2f8, sir: 0x2e8, dma: 03, irq: 7, mode: 0x02 > smsc_ircc_open > SMsC IrDA Controller found > IrCC version 2.0, firport 0x2f8, sirport 0x2e8 dma=3, irq=7 > smsc_ircc_set_sir_speed(), Setting speed to: 9600 > No transceiver found. Defaulting to Fast pin select Please, also read my driver's README. Everything about transceiver is explained there. If possible use the patch from Jean's page. It seems to me that you are not using the latest driver from my page, though. > IrDA: Registered device irda0 > smsc_superio_paged() > smsc_ircc_probe() > smsc_access() > smsc_superio_flat() > smsc_ircc_probe() > smsc_access() > smsc_superio_paged() > smsc_ircc_probe() > smsc_access() > smsc_ircc_net_open > smsc_ircc_change_speed() changing speed to: 9600 > smsc_ircc_set_sir_speed(), Setting speed to: 9600 > irlap_change_speed(), setting speed to 9600 > ircc_init() > ircc_init Try to open all known SMC chipsets Did you try to load the modules again? > > smc_superio_flat() > smc_probe() > smc_access() > smc_superio_paged() > smc_probe() > smc_access() > smc_superio_flat() > smc_probe() > smc_access() > smc_superio_paged() > smc_probe() > smc_access() > smc_superio_flat() > smc_probe() > smc_access() > smc_superio_paged() > smc_probe() > smc_access() > smc_superio_flat() > smc_probe() > smc_access() > smc_access() > smc_access() > found SMC SuperIO Chip (devid=0x5a rev=00 base=0x002e): LPC47N227 > ircc_open() > ircc_open: can't get fir_base of 0x2f8 ...and it founds the io-base already taken... > smc_superio_paged() > smc_probe() > smc_access() > smc_access() > smc_superio_flat() > smc_probe() > smc_access() > smc_superio_paged() > smc_probe() > smc_access() > smsc_ircc_hard_xmit_sir() > smsc_ircc_hard_xmit_sir() > smsc_ircc_hard_xmit_sir() > ... > ... ( lots of smae lines !!!) > smsc_ircc_hard_xmit_sir() > smsc_ircc_hard_xmit_sir() > smsc_ircc_hard_xmit_sir() > gott:~ # Check the version of my driver you are using. There should not be any of "smsc_ircc_hard_xmit_sir()" messages... In any case you are using SIR so I guess you have other problems. Good luck, Daniele |