From: Zachár B. <za...@di...> - 2006-12-11 11:16:00
|
Hello @list! I am would like to use IPERF v 2.0.2 from source to performance my network connection between two nodes, wich are link each other with a CAT 6 cross Giga cable... I run the A-node this command: iperf -s And I run some test from B-node: 1. iperf -c 10.0.0.1 -t 30 2>&1 The output: [ 3] local 10.0.0.2 port 60779 connected with 10.0.0.1 port 5001 [ 3] 0.0-30.0 sec 3.29 GBytes 941 Mbits/sec It was success! 2., iperf -c 10.0.0.1 -d -t 30 2>&1 Out: [ 4] local 10.0.0.2 port 60780 connected with 10.0.0.1 port 5001 [ 5] local 10.0.0.2 port 5001 connected with 10.0.0.1 port 47810 [ 4] 0.0-30.0 sec 2.82 GBytes 806 Mbits/sec [ 5] 0.0-30.0 sec 2.82 GBytes 806 Mbits/sec SUCCESS! 3., iperf -c 10.0.0.1 -P10 -t 30 2>&1 Out: [ 12] local 10.0.0.2 port 60790 connected with 10.0.0.1 port 5001 [ 4] local 10.0.0.2 port 60782 connected with 10.0.0.1 port 5001 [ 5] local 10.0.0.2 port 60783 connected with 10.0.0.1 port 5001 [ 8] local 10.0.0.2 port 60786 connected with 10.0.0.1 port 5001 [ 7] local 10.0.0.2 port 60785 connected with 10.0.0.1 port 5001 [ 6] local 10.0.0.2 port 60784 connected with 10.0.0.1 port 5001 [ 9] local 10.0.0.2 port 60787 connected with 10.0.0.1 port 5001 [ 10] local 10.0.0.2 port 60788 connected with 10.0.0.1 port 5001 [ 3] local 10.0.0.2 port 60781 connected with 10.0.0.1 port 5001 [ 11] local 10.0.0.2 port 60789 connected with 10.0.0.1 port 5001 [ 12] 0.0-30.0 sec 335 MBytes 93.8 Mbits/sec [ 4] 0.0-30.0 sec 334 MBytes 93.3 Mbits/sec [ 6] 0.0-30.0 sec 335 MBytes 93.6 Mbits/sec [ 9] 0.0-30.0 sec 351 MBytes 98.2 Mbits/sec [ 10] 0.0-30.0 sec 333 MBytes 93.2 Mbits/sec [ 3] 0.0-30.0 sec 335 MBytes 93.7 Mbits/sec [ 11] 0.0-30.0 sec 337 MBytes 94.1 Mbits/sec [ 5] 0.0-30.0 sec 336 MBytes 94.1 Mbits/sec [ 8] 0.0-30.0 sec 334 MBytes 93.4 Mbits/sec [ 7] 0.0-30.0 sec 335 MBytes 93.8 Mbits/sec [SUM] 0.0-30.0 sec 3.29 GBytes 941 Mbits/sec SUCCESS! BUT: 4., iperf -c 10.0.0.1 -d -P10 -t 30 2>&1 Out on the A-node: write2 failed: Broken pipe write2 failed: Broken pipe write2 failed: Broken pipe connect failed: Connection refused connect failed: Connection refused connect failed: Connection refused connect failed: Connection refused connect failed: Connection refused connect failed: Connection refused connect failed: Connection refused [ 76] local 0.0.0.0 port 40785 connected with 10.0.0.2 port 5001 [ 76] 0.0- 0.0 sec 0.00 Bytes 0.00 bits/sec [ 25] local 0.0.0.0 port 40776 connected with 10.0.0.2 port 5001 [ 25] 0.0- 0.0 sec 0.00 Bytes 0.00 bits/sec [ 28] local 0.0.0.0 port 40777 connected with 10.0.0.2 port 5001 [ 28] 0.0- 0.0 sec 0.00 Bytes 0.00 bits/sec [ 43] local 0.0.0.0 port 40778 connected with 10.0.0.2 port 5001 [ 43] 0.0- 0.0 sec 0.00 Bytes 0.00 bits/sec [ 44] local 0.0.0.0 port 40779 connected with 10.0.0.2 port 5001 [ 44] 0.0- 0.0 sec 0.00 Bytes 0.00 bits/sec And on the B-node everything looks good: [ 3] local 10.0.0.2 port 37181 connected with 10.0.0.1 port 5001 [ 6] local 10.0.0.2 port 37184 connected with 10.0.0.1 port 5001 [ 7] local 10.0.0.2 port 37186 connected with 10.0.0.1 port 5001 [ 4] local 10.0.0.2 port 37182 connected with 10.0.0.1 port 5001 [ 9] local 10.0.0.2 port 37187 connected with 10.0.0.1 port 5001 [ 10] local 10.0.0.2 port 37188 connected with 10.0.0.1 port 5001 [ 11] local 10.0.0.2 port 37189 connected with 10.0.0.1 port 5001 [ 8] local 10.0.0.2 port 37185 connected with 10.0.0.1 port 5001 [ 14] local 10.0.0.2 port 5001 connected with 10.0.0.1 port 40699 [ 15] local 10.0.0.2 port 5001 connected with 10.0.0.1 port 40700 [ 12] local 10.0.0.2 port 37190 connected with 10.0.0.1 port 5001 [ 16] local 10.0.0.2 port 5001 connected with 10.0.0.1 port 40701 [ 17] local 10.0.0.2 port 5001 connected with 10.0.0.1 port 40702 [ 18] local 10.0.0.2 port 5001 connected with 10.0.0.1 port 40703 [ 5] local 10.0.0.2 port 37183 connected with 10.0.0.1 port 5001 [ 19] local 10.0.0.2 port 5001 connected with 10.0.0.1 port 40704 [ 20] local 10.0.0.2 port 5001 connected with 10.0.0.1 port 40705 [ 21] local 10.0.0.2 port 5001 connected with 10.0.0.1 port 40706 [ 22] local 10.0.0.2 port 5001 connected with 10.0.0.1 port 40707 [ 23] local 10.0.0.2 port 5001 connected with 10.0.0.1 port 40708 [ 3] 0.0-30.0 sec 329 MBytes 92.0 Mbits/sec [ 6] 0.0-30.0 sec 327 MBytes 91.6 Mbits/sec [ 7] 0.0-30.0 sec 328 MBytes 91.6 Mbits/sec [ 4] 0.0-30.0 sec 328 MBytes 91.6 Mbits/sec [ 9] 0.0-30.0 sec 329 MBytes 91.9 Mbits/sec [ 10] 0.0-30.0 sec 327 MBytes 91.5 Mbits/sec [ 11] 0.0-30.0 sec 313 MBytes 87.6 Mbits/sec [ 8] 0.0-30.0 sec 328 MBytes 91.7 Mbits/sec [ 5] 0.0-30.0 sec 329 MBytes 91.9 Mbits/sec [ 14] 0.0-30.0 sec 325 MBytes 90.9 Mbits/sec [ 12] 0.0-30.0 sec 316 MBytes 88.4 Mbits/sec [SUM] 0.0-30.0 sec 3.18 GBytes 910 Mbits/sec [ 16] 0.0-30.0 sec 326 MBytes 91.3 Mbits/sec [ 17] 0.0-30.0 sec 326 MBytes 91.2 Mbits/sec [ 18] 0.0-30.0 sec 326 MBytes 91.2 Mbits/sec [ 15] 0.0-30.0 sec 327 MBytes 91.3 Mbits/sec [ 19] 0.0-30.0 sec 327 MBytes 91.5 Mbits/sec [ 20] 0.0-30.0 sec 325 MBytes 90.8 Mbits/sec [ 21] 0.0-30.0 sec 325 MBytes 90.8 Mbits/sec [ 22] 0.0-30.0 sec 326 MBytes 91.0 Mbits/sec [ 23] 0.0-30.0 sec 327 MBytes 91.5 Mbits/sec [SUM] 0.0-30.0 sec 3.18 GBytes 911 Mbits/sec It is a BUG or there are some problem with my network! Sorry for the long message! Regards, Balázs |