From: Neil M. <ne...@gu...> - 2012-04-02 16:14:44
|
Hi Daniel, What does the label on your Chestnut show? - Neil On Wed, Aug 3, 2011 at 7:51 PM, Daniel Beer <dl...@gm...> wrote: > Hi all, > > I've recently ordered an Overo Tide and a Chestnut43 board. I built the > OpenEmbedded omap3-console-image as described in the instructions on > the Developer Center website. My OpenEmbedded repository is at commit > d33b2275f9c345035d623b1a86ea56326567ddf3 (overo-2011.03 branch). > > After booting the board, I found that neither the Ethernet nor the USB > appear to work. U-Boot reports the following during boot: > > Net: smc911x: Invalid chip endian 0xff40ff40 > > When I plug a device into the USB port, nothing happens at all -- no > messages from the kernel. lsusb shows the root hub, but nothing else. > > The label on top of the Tide board reads: > > W/O 27834 11-25 > GS3503T-R2889 > INN W/O# 70445 > > I've also tried the pre-built image from the website and building a > minimal system from the appropriate git repositories for U-Boot and > Linux, with the same results. > > Is this a hardware fault? Let me know if there's any further > information I can provide. I've included a full boot log below. > > - Daniel > > ------------------------------------------------------------------------ > Texas Instruments X-Loader 1.4.4ss (Aug 2 2011 - 14:36:57) > No NAND detected > OMAP3530-GP ES3.1 > Board revision: 1 > Reading boot sector > Loading u-boot.bin from mmc > > > U-Boot 2010.12 (Aug 04 2011 - 11:47:07) > > OMAP3530-GP ES3.1, CPU-OPP2, L3-165MHz, Max CPU Clock 720 mHz > Gumstix Overo board + LPDDR/NAND > I2C: ready > DRAM: 512 MiB > NAND: nand_get_flash_type: unknown NAND device: Manufacturer ID: 0x40, Chip ID: 0x40 > 0 MiB > MMC: OMAP SD/MMC: 0 > *** Warning - readenv() failed, using default environment > > In: serial > Out: serial > Err: serial > Board revision: 1 > Direct connection on mmc2 > No EEPROM on expansion board > Die ID #633a0004000000000403951c08001012 > Net: smc911x: Invalid chip endian 0xff40ff40 > No ethernet found. > Hit any key to stop autoboot: 0 > reading boot.scr > > ** Unable to read "boot.scr" from mmc 0:1 ** > reading uImage > > 2914780 bytes read > Booting from mmc ... > ## Booting kernel from Legacy Image at 82000000 ... > Image Name: Angstrom/2.6.39/overo > Image Type: ARM Linux Kernel Image (uncompressed) > Data Size: 2914716 Bytes = 2.8 MiB > Load Address: 80008000 > Entry Point: 80008000 > Verifying Checksum ... OK > Loading Kernel Image ... OK > OK > > Starting kernel ... > > Uncompressing Linux... done, booting the kernel. > Linux version 2.6.39 (dlbeer@soma) (gcc version 4.3.3 (GCC) ) #1 Thu Aug 4 06:11:16 NZST 2011 > CPU: ARMv7 Processor [411fc083] revision 3 (ARMv7), cr=10c53c7f > CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache > Machine: Gumstix Overo > Reserving 12582912 bytes SDRAM for VRAM > Memory policy: ECC disabled, Data cache writeback > OMAP3430/3530 ES3.1 (l2cache iva sgx neon isp ) > SRAM: Mapped pa 0x40200000 to va 0xfe400000 size: 0x10000 > Clocking rate (Crystal/Core/MPU): 26.0/224/500 MHz > Reprogramming SDRC clock to 224791666 Hz > dpll3_m2_clk rate change failed: -22 > Built 1 zonelists in Zone order, mobility grouping on. Total pages: 126976 > Kernel command line: console=ttyO2,115200n8 mpurate=720 vram=12M omapfb.mode=dvi:1024x768MR-16@60 omapdss.def_disp=dvi root=/dev/mmcblk0p2 rw rootfstype=ext3 rootwait > PID hash table entries: 2048 (order: 1, 8192 bytes) > Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) > Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) > Memory: 500MB = 500MB total > Memory: 501204k/501204k available, 23084k reserved, 0K highmem > Virtual kernel memory layout: > vector : 0xffff0000 - 0xffff1000 ( 4 kB) > fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) > DMA : 0xffc00000 - 0xffe00000 ( 2 MB) > vmalloc : 0xe0800000 - 0xf8000000 ( 376 MB) > lowmem : 0xc0000000 - 0xe0000000 ( 512 MB) > modules : 0xbf000000 - 0xc0000000 ( 16 MB) > .init : 0xc0008000 - 0xc0039000 ( 196 kB) > .text : 0xc0039000 - 0xc0574944 (5359 kB) > .data : 0xc0576000 - 0xc05b75c0 ( 262 kB) > NR_IRQS:410 > IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96 interrupts > Total of 96 interrupts on 1 active controller > OMAP clockevent source: GPTIMER1 at 32768 Hz > sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every 131071999ms > Console: colour dummy device 80x30 > Calibrating delay loop... 497.82 BogoMIPS (lpj=1941504) > pid_max: default: 32768 minimum: 301 > Mount-cache hash table entries: 512 > CPU: Testing write buffer coherency: ok > devtmpfs: initialized > omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for l4_core > omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for l4_per > omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for l4_wkup > omap_hwmod: gpt12_fck: missing clockdomain for gpt12_fck. > omap_hwmod: i2c1: softreset failed (waited 10000 usec) > omap_hwmod: i2c2: softreset failed (waited 10000 usec) > omap_hwmod: i2c3: softreset failed (waited 10000 usec) > omap_hwmod: am35x_otg_hs: cannot be enabled (3) > print_constraints: dummy: > NET: Registered protocol family 16 > GPMC revision 5.0 > OMAP GPIO hardware version 2.5 > OMAP GPIO hardware version 2.5 > OMAP GPIO hardware version 2.5 > OMAP GPIO hardware version 2.5 > OMAP GPIO hardware version 2.5 > OMAP GPIO hardware version 2.5 > omap_mux_init: Add partition: #1: core, flags: 0 > Found NAND on CS0 > Registering NAND on CS0 > hw-breakpoint: debug architecture 0x4 unsupported. > Switched to new clocking rate (Crystal/Core/MPU): 26.0/224/720 MHz > OMAP DMA hardware revision 4.0 > bio: create slab <bio-0> at 0 > print_constraints: vads7846: 3300 mV > SCSI subsystem initialized > usbcore: registered new interface driver usbfs > usbcore: registered new interface driver hub > usbcore: registered new device driver usb > omap_i2c omap_i2c.1: bus 1 rev3.12 at 2600 kHz > twl4030: PIH (irq 7) chaining IRQs 368..375 > twl4030: power (irq 373) chaining IRQs 376..383 > twl4030: gpio (irq 368) chaining IRQs 384..401 > print_constraints: VUSB1V5: 1500 mV normal standby > print_constraints: VUSB1V8: 1800 mV normal standby > print_constraints: VUSB3V1: 3100 mV normal standby > twl4030_usb twl4030_usb: Initialized TWL4030 USB module > print_constraints: VMMC1: 1850 <--> 3150 mV at 3000 mV normal standby > print_constraints: VDAC: 1800 mV normal standby > print_constraints: VDVI: 1800 mV normal standby > omap_i2c omap_i2c.3: bus 3 rev3.12 at 400 kHz > Advanced Linux Sound Architecture Driver Version 1.0.24. > Bluetooth: Core ver 2.16 > NET: Registered protocol family 31 > Bluetooth: HCI device and connection manager initialized > Bluetooth: HCI socket layer initialized > Bluetooth: L2CAP socket layer initialized > Bluetooth: SCO socket layer initialized > Switching to clocksource 32k_counter > Switched to NOHz mode on CPU #0 > musb-hdrc: version 6.0, musb-dma, host, debug=0 > musb-hdrc musb-hdrc: MUSB HDRC host driver > musb-hdrc musb-hdrc: new USB bus registered, assigned bus number 1 > usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 > usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 > usb usb1: Product: MUSB HDRC host driver > usb usb1: Manufacturer: Linux 2.6.39 musb-hcd > usb usb1: SerialNumber: musb-hdrc > hub 1-0:1.0: USB hub found > hub 1-0:1.0: 1 port detected > musb-hdrc musb-hdrc: USB Host mode controller at fa0ab000 using DMA, IRQ 92 > NET: Registered protocol family 2 > IP route cache hash table entries: 4096 (order: 2, 16384 bytes) > TCP established hash table entries: 16384 (order: 5, 131072 bytes) > TCP bind hash table entries: 16384 (order: 4, 65536 bytes) > TCP: Hash tables configured (established 16384 bind 16384) > TCP reno registered > UDP hash table entries: 256 (order: 0, 4096 bytes) > UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) > NET: Registered protocol family 1 > RPC: Registered udp transport module. > RPC: Registered tcp transport module. > RPC: Registered tcp NFSv4.1 backchannel transport module. > VFS: Disk quotas dquot_6.5.2 > Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) > Registering unionfs 2.5.9 (for 2.6.39-rc5) > JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. > msgmni has been set to 978 > Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) > io scheduler noop registered > io scheduler deadline registered > io scheduler cfq registered (default) > OMAP DSS rev 2.0 > Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled > omap_uart.0: ttyO0 at MMIO 0x4806a000 (irq = 72) is a OMAP UART0 > omap_uart.1: ttyO1 at MMIO 0x4806c000 (irq = 73) is a OMAP UART1 > omap_uart.2: ttyO2 at MMIO 0x49020000 (irq = 74) is a OMAP UART2 > console [ttyO2] enabled > brd: module loaded > loop: module loaded > omap2-nand driver initializing > No NAND device found. > No NAND device found. > smsc911x: Driver version 2008-10-21. > smsc911x: Driver version 2008-10-21. > usbcore: registered new interface driver asix > usbcore: registered new interface driver cdc_ether > cdc_ncm: 23-Apr-2011 > usbcore: registered new interface driver cdc_ncm > ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver > ehci-omap ehci-omap.0: OMAP-EHCI Host Controller > ehci-omap ehci-omap.0: new USB bus registered, assigned bus number 2 > ehci-omap ehci-omap.0: irq 77, io mem 0x48064800 > ehci-omap ehci-omap.0: USB 2.0 started, EHCI 1.00 > usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 > usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 > usb usb2: Product: OMAP-EHCI Host Controller > usb usb2: Manufacturer: Linux 2.6.39 ehci_hcd > usb usb2: SerialNumber: ehci-omap.0 > hub 2-0:1.0: USB hub found > hub 2-0:1.0: 3 ports detected > Initializing USB Mass Storage driver... > usbcore: registered new interface driver usb-storage > USB Mass Storage support registered. > udc: OMAP UDC driver, version: 4 October 2004 (iso) (dma) > mousedev: PS/2 mouse device common for all mice > twl_rtc twl_rtc: rtc core: registered twl_rtc as rtc0 > twl_rtc twl_rtc: Power up reset detected. > i2c /dev entries driver > OMAP Watchdog Timer Rev 0x31: initial timeout 60 sec > Bluetooth: HCI UART driver ver 2.2 > Bluetooth: HCI H4 protocol initialized > Bluetooth: HCI BCSP protocol initialized > Bluetooth: HCILL protocol initialized > cpuidle: using governor ladder > cpuidle: using governor menu > usbcore: registered new interface driver usbhid > usbhid: USB HID core driver > usbcore: registered new interface driver snd-usb-audio > overo SoC init > asoc: twl4030-hifi <-> omap-mcbsp-dai.1 mapping ok > ALSA device list: > #0: overo > oprofile: hardware counters not available > oprofile: using timer interrupt. > TCP cubic registered > NET: Registered protocol family 17 > NET: Registered protocol family 15 > Bluetooth: RFCOMM TTY layer initialized > Bluetooth: RFCOMM socket layer initialized > Bluetooth: RFCOMM ver 1.11 > Bluetooth: BNEP (Ethernet Emulation) ver 1.3 > Bluetooth: BNEP filters: protocol multicast > Bluetooth: HIDP (Human Interface Emulation) ver 1.2 > Registering the dns_resolver key type > VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 1 > ThumbEE CPU extension supported. > omap2_set_init_voltage: unable to find boot up OPP for vdd_mpu > omap2_set_init_voltage: Unable to put vdd_mpu to its init voltage > > Power Management for TI OMAP3. > sr_init: No PMIC hook to init smartreflex > smartreflex smartreflex.0: omap_sr_probe: SmartReflex driver initialized > smartreflex smartreflex.1: omap_sr_probe: SmartReflex driver initialized > clock: disabling unused clocks to save power > fbcvt: 1024x768@60: CVT Name - .786M3-R > Console: switching to colour frame buffer device 128x48 > regulator_init_complete: VDAC: incomplete constraints, leaving on > regulator_init_complete: vads7846: incomplete constraints, leaving on > twl_rtc twl_rtc: setting system clock to 2000-01-01 00:00:09 UTC (946684809) > Waiting for root device /dev/mmcblk0p2... > mmc0: host does not support reading read-only switch. assuming write-enable. > mmc0: new high speed SDHC card at address 1234 > mmcblk0: mmc0:1234 SA04G 3.67 GiB > mmcblk0: detected capacity change from 0 to 3951034368 > mmcblk0: p1 p2 > EXT3-fs: barriers not enabled > kjournald starting. Commit interval 5 seconds > EXT3-fs (mmcblk0p2): using internal journal > EXT3-fs (mmcblk0p2): recovery complete > EXT3-fs (mmcblk0p2): mounted filesystem with writeback data mode > VFS: Mounted root (ext3 filesystem) on device 179:2. > devtmpfs: mounted > INIT: version 2.86 booting > Please wait: booting... > Starting udev > udev: starting version 151 > udevd (73): /proc/73/oom_adj is deprecated, please use /proc/73/oom_score_adj instead. > ads7846 spi1.0: touchscreen, irq 274 > ads7846 spi1.0: no device detected, test read result was 0x00000000 > usbcore: registered new interface driver usbserial > USB Serial support registered for generic > usbcore: registered new interface driver usbserial_generic > usbserial: USB Serial Driver core > USB Serial support registered for GSM modem (1-port) > usbcore: registered new interface driver option > option: v0.7.2:USB Driver for GSM modems > Remounting root file system... > > udevadm settle - timeout of 8 seconds reached, the event queue contains: > /sys/devices/platform/omap/omap_hsmmc.0/mmc_host/mmc0/mmc0:1234/block/mmcblk0 (615) > /sys/devices/platform/omap/omap_hsmmc.0/mmc_host/mmc0/mmc0:1234/block/mmcblk0/mmcblk0p1 (616) > /sys/devices/platform/omap/omap_hsmmc.0/mmc_host/mmc0/mmc0:1234/block/mmcblk0/mmcblk0p2 (617) > Caching udev devnodes > Populating dev cache > NET: Registered protocol family 10 > ALSA: Restoring mixer settings... > Cleaning: /etc/network/run/ifstate. > Configuring network interfaces... eth0: unknown interface: No such device > eth0: unknown interface: No such device > eth0 No such device > > Internet Systems Consortium DHCP Client 4.1.1-P1 > Copyright 2004-2010 Internet Systems Consortium. > All rights reserved. > For info, please visit https://www.isc.org/software/dhcp/ > > SIOCSIFADDR: No such device > eth0: unknown interface: No such device > eth0: unknown interface: No such device > Bind socket to interface: No such device > > If you did not get this software from ftp.isc.org, please > get the latest from ftp.isc.org and install that before > requesting help. > > If you did get this software from ftp.isc.org and have not > yet read the README, please read it before requesting help. > If you intend to request help from the dhc...@is... > mailing list, please read the section on the README about > submitting bug reports and requests for help. > > Please do not under any circumstances send requests for > help directly to the authors of this software - please > send them to the appropriate mailing list as described in > the README file. > > exiting. > Failed to bring up eth0. > done. > Starting portmap daemon: portmap. > net.ipv4.conf.default.rp_filter = 1 > net.ipv4.conf.all.rp_filter = 1 > Thu Aug 4 13:13:00 UTC 2011 > INIT: Entering runlevel: 5 > Starting system message bus: dbus. > Starting Hardware abstraction layer hald > Starting OpenBSD Secure Shell server: sshd > done. > Starting advanced power management daemon: No APM support in kernel > (failed.) > Starting ntpd: done > Starting syslog-ng:. > * Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon [ ok ] > Starting Bluetooth subsystem: > Initialization timed out. > > .---O---. > | | .-. o o > | | |-----.-----.-----.| | .----..-----.-----. > | | | __ | ---'| '--.| .-'| | | > | | | | | |--- || --'| | | ' | | | | > '---'---'--'--'--. |-----''----''--' '-----'-'-'-' > -' | > '---' > > The Angstrom Distribution overo ttyO2 > > Angstrom 2011.03 overo ttyO2 > > overo login: > > ------------------------------------------------------------------------------ > BlackBerry® DevCon Americas, Oct. 18-20, San Francisco, CA > The must-attend event for mobile developers. Connect with experts. > Get tools for creating Super Apps. See the latest technologies. > Sessions, hands-on labs, demos & much more. Register early & save! > http://p.sf.net/sfu/rim-blackberry-1 > _______________________________________________ > gumstix-users mailing list > gum...@li... > https://lists.sourceforge.net/lists/listinfo/gumstix-users |