Menu
▾
▴
Re: [Gumstix-users] Overo Desktop - Palmtop images
|
From: Demetris <fgc...@cy...> - 2009-08-14 18:53:11
|
I appreciate the info. However, I am not using currently any networking and
simply want the system to boot. So I assume I could sizable this for now?
Also I tried to run the app after I login but from what I could remember I
used to do export DISPLAY=:0 but now it seems to be incorrect. Any ideas
on this?
_____
From: richard dorfner [mailto:rdo...@gm...]
Sent: Friday, August 14, 2009 9:46 PM
To: General mailing list for gumstix users.
Subject: Re: [Gumstix-users] Overo Desktop - Palmtop images
It looks like the DNS server is dieing which would implay either no
connectivy, or poor connectivity or something got changed with your ifconfig
or the wifi config causing it to no longer be connected .. or possibly a
misconnected or loose cable on the ethernet port.
Another possibility is that DNS has somehow become misconfigured and so is
no longer going to the right IP address for DNS information.
Also, when I was mentioning dmesg, I was referring to the "dmesg" command
that spits out kernel message information. Once the kernel is up and
running, and you have a consol login prompt, if you can try invoking the
program you want to have run against the display (not sure how, I'd have to
look it up and I don't have a system to test this on that uses a display)
then if it does not work right, typing 'dmesg' might give you more clues as
to what's going wrong, since the programs might log messages instead of
spitting them out to the console.
Rick
On Fri, Aug 14, 2009 at 2:15 PM, Demetris <fgc...@cy...> wrote:
There are some errors but I am not sure if they are relevant. The platform I
am testing this on is FIRE. Below is my entire Boot log (this is the Desktop
Image which doesnt go to the end for some reason, the palmtop image however
goes but doesnt load the desktop):
U-Boot 2009.03 (Jun 23 2009 - 21:29:05)
OMAP3530-GP rev 2, CPU-OPP2 L3-165MHz
Gumstix Overo board + LPDDR/NAND
DRAM: 256 MB
NAND: 256 MiB
In: serial
Out: serial
Err: serial
Die ID #0f6a00040000000004032d460c018009
Hit any key to stop autoboot: 0
reading boot.scr
** Unable to read "boot.scr" from mmc 0:1 **
reading uImage
2725300 bytes read
Booting from mmc ...
## Booting kernel from Legacy Image at 82000000 ...
Image Name: Angstrom/2.6.29/overo
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2725236 Bytes = 2.6 MB
Load Address: 80008000
Entry Point: 80008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Starting kernel ...
Uncompressing
Linux.............................................................
............................................................................
....
....................................... done, booting the kernel.
Linux version 2.6.29-omap1 (dima@dima-desktop) (gcc version 4.3.3 (GCC) ) #1
Mon
Aug 3 01:36:44 EEST 2009
CPU: ARMv7 Processor [411fc083] revision 3 (ARMv7), cr=10c5387f
CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
Machine: Gumstix Overo
omapfb_early_vram, 33554432, 0x0
Memory policy: ECC disabled, Data cache writeback
OMAP3430 ES3.1
SRAM: Mapped pa 0x40200000 to va 0xd7000000 size: 0x100000
Reserving 33554432 bytes SDRAM for VRAM
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024
Kernel command line: console=ttyS2,115200n8 vram=32M
omapfb.mode=dvi:1024x768MR-
16@60 omapfb.debug=y omapdss.def_disp=lcd43 root=/dev/mmcblk0p2 rw
rootfstype=ex
t3 rootwait
Clocking rate (Crystal/DPLL/ARM core): 26.0/331/500 MHz
GPMC revision 5.0
IRQ: Found an INTC at 0xd8200000 (revision 4.0) with 96 interrupts
Total of 96 interrupts on 1 active controller
OMAP34xx GPIO hardware version 2.5
PID hash table entries: 1024 (order: 10, 4096 bytes)
OMAP clockevent source: GPTIMER1 at 32768 Hz
Console: colour dummy device 80x30
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 128MB 128MB = 256MB total
Memory: 220928KB available (4472K code, 532K data, 940K init)
Calibrating delay loop... 499.92 BogoMIPS (lpj=1949696)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
net_namespace: 764 bytes
regulator: core version 0.5
NET: Registered protocol family 16
Found NAND on CS0
Registering NAND on CS0
OMAP DMA hardware revision 4.0
bio: create slab <bio-0> at 0
OMAP DSS rev 2.0
OMAP DISPC rev 3.0
OMAP VENC rev 2
i2c_omap i2c_omap.1: bus 1 rev3.12 at 2600 kHz
twl4030: PIH (irq 7) chaining IRQs 368..375
twl4030: power (irq 373) chaining IRQs 376..383
twl4030: gpio (irq 368) chaining IRQs 384..401
regulator: VMMC1: 1850 <--> 3150 mV normal standby
regulator: VUSB1V5: 1500 <--> 0 mV normal standby
regulator: VUSB1V8: 1800 <--> 0 mV normal standby
regulator: VUSB3V1: 3100 <--> 0 mV normal standby
i2c_omap i2c_omap.3: bus 3 rev3.12 at 400 kHz
SCSI subsystem initialized
twl4030_usb twl4030_usb: Initialized TWL4030 USB module
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Bluetooth: Core ver 2.14
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
cfg80211: Using static regulatory domain info
cfg80211: Regulatory domain: US
(start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
(2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm)
(5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm)
cfg80211: Calling CRDA for country: US
musb_hdrc: version 6.0, musb-dma, host, debug=0
musb_hdrc: USB Host mode controller at d80ab000 using DMA, IRQ 92
musb_hdrc musb_hdrc: MUSB HDRC host driver
musb_hdrc musb_hdrc: new USB bus registered, assigned bus number 1
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: MUSB HDRC host driver
usb usb1: Manufacturer: Linux 2.6.29-omap1 musb-hcd
usb usb1: SerialNumber: musb_hdrc
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
NET: Registered protocol family 1
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
msgmni has been set to 431
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
serial8250.0: ttyS0 at MMIO 0x4806a000 (irq = 72) is a ST16654
serial8250.0: ttyS1 at MMIO 0x4806c000 (irq = 73) is a ST16654
serial8250.0: ttyS2 at MMIO 0x49020000 (irq = 74) is a ST16654
console [ttyS2] enabled
brd: module loaded
loop: module loaded
usbcore: registered new interface driver asix
usbcore: registered new interface driver cdc_ether
i2c /dev entries driver
Driver 'sd' needs updating - please use bus_type methods
omap2-nand driver initializing
NAND device: Manufacturer ID: 0x2c, Chip ID: 0xba (Micron NAND 256MiB 1,8V
16-bi
t)
cmdlinepart partition parsing not available
Creating 5 MTD partitions on "omap2-nand":
0x000000000000-0x000000080000 : "xloader"
0x000000080000-0x000000240000 : "uboot"
0x000000240000-0x000000280000 : "uboot environment"
0x000000280000-0x000000680000 : "linux"
0x000000680000-0x000010000000 : "rootfs"
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-omap ehci-omap.0: OMAP-EHCI Host Controller
ehci-omap ehci-omap.0: new USB bus registered, assigned bus number 2
ehci-omap ehci-omap.0: irq 77, io mem 0x48064800
ehci-omap ehci-omap.0: USB 2.0 started, EHCI 1.00
usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: OMAP-EHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.29-omap1 ehci_hcd
usb usb2: SerialNumber: ehci-omap.0
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
udc: OMAP UDC driver, version: 4 October 2004 (iso) (dma)
mice: PS/2 mouse device common for all mice
twl4030_rtc twl4030_rtc: rtc core: registered twl4030_rtc as rtc0
twl4030_rtc twl4030_rtc: Power up reset detected.
twl4030_rtc twl4030_rtc: Enabling TWL4030-RTC.
OMAP Watchdog Timer Rev 0x31: initial timeout 60 sec
Bluetooth: HCI UART driver ver 2.2
Bluetooth: HCI H4 protocol initialized
Bluetooth: HCI BCSP protocol initialized
Bluetooth: Broadcom Blutonium firmware driver ver 1.2
usbcore: registered new interface driver bcm203x
Bluetooth: Digianswer Bluetooth USB driver ver 0.10
usbcore: registered new interface driver bpa10x
mmci-omap-hs mmci-omap-hs.0: Failed to get debounce clock
regulator: Unable to get requested regulator: vmmc_aux
mmci-omap-hs mmci-omap-hs.1: Failed to get debounce clock
regulator: Unable to get requested regulator: vmmc
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
Advanced Linux Sound Architecture Driver Version 1.0.18a.
usbcore: registered new interface driver snd-usb-audio
No device for DAI twl4030
No device for DAI omap-mcbsp-dai-0
No device for DAI omap-mcbsp-dai-1
No device for DAI omap-mcbsp-dai-2
No device for DAI omap-mcbsp-dai-3
No device for DAI omap-mcbsp-dai-4
overo SoC init
TWL4030 Audio Codec init
asoc: twl4030 <-> omap-mcbsp-dai-0 mapping ok
ALSA device list:
#0: overo (twl4030)
oprofile: using arm/armv7
TCP cubic registered
NET: Registered protocol family 17
NET: Registered protocol family 15
Bluetooth: L2CAP ver 2.11
Bluetooth: L2CAP socket layer initialized
Bluetooth: SCO (Voice Link) ver 0.6
Bluetooth: SCO socket layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM ver 1.10
Bluetooth: BNEP (Ethernet Emulation) ver 1.3
Bluetooth: BNEP filters: protocol multicast
Bluetooth: HIDP (Human Interface Emulation) ver 1.2
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
ThumbEE CPU extension supported.
Power Management for TI OMAP3.
SmartReflex driver initialized
VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 1
mmc0: mmc_rescan - card ocr from io_op=0x00000000, err = -110
fbcvt: 1024x768@60: CVT Name - .786M3-R
Console: switching to colour frame buffer device 60x40
clock: clksel_round_rate_div: dpll4_m4_ck target_rate 28800000
clock: new_div = 15, new_rate = 28800000
twl4030_rtc twl4030_rtc: setting system clock to 2000-01-01 00:00:00 UTC
(946684
800)
Waiting for root device /dev/mmcblk0p2...
mmc0: host does not support reading read-only switch. assuming write-enable.
mmc0: new high speed SD card at address 0007
mmcblk0: mmc0:0007 SD01G 972 MiB
mmcblk0: p1 p2
mmc1: mmc_rescan - card ocr from io_op=0x90ff8000, err = 0
mmc1: new SDIO card at address 0001
kjournald starting. Commit interval 5 seconds
EXT3 FS on mmcblk0p2, internal journal
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) on device 179:2.
Freeing init memory: 940K
INIT: version 2.86 booting
Please wait: booting...
Starting udevudev: starting version 141
Remounting root file system...
ads7846 spi1.0: touchscreen, irq 274
input: ADS784x Touchscreen as
/devices/platform/omap2_mcspi.1/spi1.0/input/input
0
lib80211: common routines for IEEE802.11 drivers
libertas_sdio: Libertas SDIO driver
libertas_sdio: Copyright Pierre Ossman
libertas_sdio mmc1:0001:1: firmware: requesting sd8686_helper.bin
NET: Registered protocol family 10
libertas_sdio mmc1:0001:1: firmware: requesting sd8686.bin
Unknown HZ value! (78) Assume 100.
ALSA: Restoring mixer settings...
Configuring network interfaces... done.
Starting portmap daemon: portmap.
libertas: 00:19:88:20:71:db, fw 9.70.3p24, cap 0x00000303
eth0 (libertas_sdio): not using net_device_ops yet
Unknown HZ value! (80) Assume 100.
net.ipv4.conf.default.rp_filter = 1
net.ipv4.conf.all.rp_filter = 1
libertas: PREP_CMD: command 0x00a3 failed: 2
libertas: PREP_CMD: command 0x00a3 failed: 2
libertas: eth0: Marvell WLAN 802.11 adapter
Fri Aug 14 04:55:00 BST 2009
udev: renamed network interface eth0 to wlan0
Turning echo off on /dev/ttyS1
INIT: Entering runlevel: 5
Starting system message bus: dbus.
Starting Hardware abstraction layer hald
ADDRCONF(NETDEV_UP): wlan0: link is not ready
Starting Connection Manager
Starting Dropbear SSH server: dropbear.
Starting advanced power managemeADDRCONF(NETDEV_CHANGE): wlan0: link becomes
rea
dy
nt daemon: No APM support in kernel
(failed.)
Starting Samba: smbd nmbd.
Starting syslogd/klogd: done
* Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon
libertas: command 0x001f timed out
libertas: requeueing command 0x001f due to timeout (#1)
libertas: command 0x001f timed out
libertas: requeueing command 0x001f due to timeout (#2)
libertas: command 0x001f timed out
libertas: requeueing command 0x001f due to timeout (#3)
libertas: command 0x001f timed out
libertas: Excessive timeouts submitting command 0x001f
Timeout reached while wating for return value
Could not receive return value from daemon process.
*[fail]
Starting Bluetooth subsystem:
Initialization timed out.
_____
From: Demetris [mailto:fgc...@cy...]
Sent: Friday, August 14, 2009 9:07 PM
To: 'General mailing list for gumstix users.'
Subject: Re: [Gumstix-users] Overo Desktop - Palmtop images
No, at a first glance on the terminal no errors.
I tried the same thing with Desktop and Palmtop images but they all do the
same thing. The Overo logo splash screen goes up to the end and stays there
while the terminal shown up the Login screen. After a minute or so the
splash screen disappears and all that is left on the screen is the Angstrom
login.
The images I am trying are the default ones from the build environment.
_____
From: richard dorfner [mailto:rdo...@gm...]
Sent: Friday, August 14, 2009 9:01 PM
To: General mailing list for gumstix users.
Subject: Re: [Gumstix-users] Overo Desktop - Palmtop images
Is dmesg showing any errors?
On Fri, Aug 14, 2009 at 7:47 AM, Demetris <fgc...@cy...> wrote:
Hi everyone. Hope someone can help out on this. I am trying to boot the
Palmtop or Desktop images but at the very end I get the following line:
Starting GPE display manager: gpe-dm
And get into the login screen. Also the login screen appears on the LCD. But
I dont get the actual gpe-dm screen nor the desktop initial screens when
the boot completes.
Any ideas on this would be appreciated.
----------------------------------------------------------------------------
--
Let Crystal Reports handle the reporting - Free Crystal Reports 2008 30-Day
trial. Simplify your report design, integration and deployment - and focus
on
what you do best, core application coding. Discover what's new with
Crystal Reports now. http://p.sf.net/sfu/bobj-july
_______________________________________________
gumstix-users mailing list
gum...@li...
https://lists.sourceforge.net/lists/listinfo/gumstix-users
--
Say you can or say you can't, either way you will be right.
Computers are like old testament gods: Lots of rules and no mercy.
----------------------------------------------------------------------------
--
Let Crystal Reports handle the reporting - Free Crystal Reports 2008 30-Day
trial. Simplify your report design, integration and deployment - and focus
on
what you do best, core application coding. Discover what's new with
Crystal Reports now. http://p.sf.net/sfu/bobj-july
_______________________________________________
gumstix-users mailing list
gum...@li...
https://lists.sourceforge.net/lists/listinfo/gumstix-users
--
Say you can or say you can't, either way you will be right.
Computers are like old testament gods: Lots of rules and no mercy.
|