|
From: Marco v. L. <mas...@gm...> - 2016-12-22 09:04:42
|
Dear all, Thanks for the responses and suggestions. I tried again with a different PC (am away from my main PC), which has only USB 2 ports, and Ubuntu 12.04, and there it works! So it seems that this was indeed an issue with USB3 and my USB-to-serial converter. The retrieved tracks only have coordinates (longitude and latitude) and elevation information; I had hoped to retrieve also time information, but I guess that the eTrex Legends does not send this over serial; in fact, it may not even store it in tracks... I searched a bit for this and it seems to be a feature of the Garmin GPS, see e.g.: http://forums.gpsreview.net/discussion/12967/why-doesn-t-my-track-have-time-stamps Best regards, Marco. On Tue, Dec 20, 2016 at 11:33 PM, Ralf Horstmann <ral...@ac...> wrote: > I tried to reproduce on Fedora 25, with a GPSMap 60CSx set to "GARMIN" > protocol > for the serial port. An FTDI USB serial adapter works pretty reliable, > while my > Prolific adapter works or fails depending on the USB port being used. > > My laptop has one USB port that attaches to a xhci controller like yours. > With > that, the transmission fails with similar symptoms like you have seen. > When I > either disable USB 3.0 support in BIOS setup or use a port that attaches to > ehci-hcd, the Prolific adapter tends to work. > > If you have an option to use an USB 2.0 port, maybe that's worth a try. > > Regards, > Ralf > > * Marco van Leeuwen <mas...@gm...> [2016-12-17 17:19]: > > Dear all, > > > > I hope this is the right place to post my question. I have an old Garmin > > eTrex legend device and am trying to retrieve some (old) tracks from it. > > The device is connected to my PC via a serial-to-USB device. I am running > > Ubuntu 16.04. The device shows up as /dev/ttyUSB0. > > (from dmesg: > > > > [ 960.747772] usb 3-1: new full-speed USB device number 3 using xhci_hcd > > [ 960.876241] usb 3-1: New USB device found, idVendor=067b, > idProduct=2303 > > [ 960.876246] usb 3-1: New USB device strings: Mfr=0, Product=0, > > SerialNumber=0 > > [ 960.876702] pl2303 3-1:1.0: pl2303 converter detected > > [ 960.877388] usb 3-1: pl2303 converter now attached to ttyUSB0 > > > > ) > > > > When I do: > > > > gpsbabel -t -i garmin -f /dev/ttyUSB0 -o gpx -F track.gpx > > > > I get: > > > > [ERROR] A800_Off: Not acknowledged > > GPS_Packet_Read: No DLE. Data received, but probably not a garmin > packet. > > > > I've read that retrying sometimes helps, but I get: > > > > gpsbabel -t -i garmin -f /dev/ttyUSB0 -o gpx -F track.gpx > > GARMIN:Can't init /dev/ttyUSB0 > > > > I can unplug the USB-to-serial device and try again, but it only gives me > > one show and always the same error. > > > > I've also tried with the debug options: > > > > gpsbabel -D9 -i garmin -f /dev/ttyUSB0 -o gpx -F track.gpx > > > > GPSBabel Version: 1.5.2 > > GPS Serial Open at 9600 > > Tx Data:10 fe 00 02 10 03 : ...(PRDREQ ) > > Rx Data:10 15 02 02 00 e7 10 03 .. (NAK ) > > GARMIN:Can't init /dev/ttyUSB0 > > [AliEnv] mvl@multatuli:~$ gpsbabel -D9 -i garmin -f /dev/ttyUSB0 -o gpx > -F > > track.gpx > > GPSBabel Version: 1.5.2 > > GPS Serial Open at 9600 > > Tx Data:10 fe 00 02 10 03 : ...(PRDREQ ) > > Rx Data:10 06 02 fe 00 fa 10 03 .. (ACK ) > > Rx Data:10 ff 85 b3 00 86 01 65 54 72 65 78 20 4c 65 67 65 6e 64 20 53 6f > > 66 74 77 61 72 65 20 56 65 72 73 69 6f 6e 20 33 2e 39 30 00 56 45 52 42 > 4d > > 41 50 20 41 74 6c 61 6e 74 69 63 20 48 69 67 68 77 61 79 20 31 2e 30 30 > 00 > > 56 45 52 53 4d 41 50 20 43 41 4d 45 52 4f 4e 2c 20 41 5a 20 28 57 45 53 > 54 > > 29 2c 20 47 4c 45 4e 20 43 41 4e 59 4f 4e 20 44 41 4d 2c 20 41 5a 20 28 > 57 > > 45 53 54 29 2c 20 47 52 20 30 2e 30 30 00 bb 10 03 > > ....eTrex.Legend.Software.Version.3.90.VERBMAP.Atlantic. > Highway.1.00.VERSMAP.CAMERON..AZ..WEST...GLEN.CANYON.DAM.. > AZ..WEST...GR.0.00. > > (PRDDAT ) > > Tx Data:10 06 02 ff 00 f9 10 03 : .....(ACK ) > > Unit: eTrex Legend Software Version 3.90 > > ID: 179 > > Version: 3.90Rx Data:10 fd 4b 50 00 00 4c 01 00 41 0a 00 41 64 00 44 6c > 00 > > 41 c9 00 44 ca 00 44 6c 00 44 d2 00 41 2d 01 44 36 01 44 2d 01 41 f4 01 > 44 > > f5 01 41 58 02 44 58 02 41 bc 02 44 bc 02 41 20 03 44 20 03 41 22 03 44 > 22 > > 03 41 84 03 41 86 03 41 87 03 a0 10 03 > > P..L..A..Ad.Dl.A..D..Dl.D..A..D6.D..A..D..AX.DX.A..D..A..D.. > A..D..A..A..A.. > > (UNKNOWN ) > > Tx Data:10 06 02 fd 00 fb 10 03 : .....(SESACK ) > > > > Capability A10: > > Capability A100: D108 > > Capability A201: D202 D108 D210 > > Capability A301: D310 D301 > > Capability A500: D501 > > Capability A600: D600 > > Capability A700: D700 > > Capability A800: D800 > > Capability A802: D802 > > Capability A900: > > Capability A902: > > Capability A903: > > Link_type 1 Device_command 0 > > Waypoint: Transfer 100 Type 108 > > Route: Transfer 201 Header 202 Type 108 > > Track: Transfer 301 Type 301 > > Tx Data:10 0a 02 32 00 c2 10 03 : 2....(CMDDAT Xfer PVT Stop) > > Rx Data:10 63 0c 00 ff 30 31 2d 41 55 47 2d 31 31 00 98 10 03 > ..01.AUG.11. > > (TRKHDR ) > > [ERROR] A800_Off: Not acknowledged > > GPS Serial Open at 9600 > > Tx Data:10 0a 02 05 00 ef 10 03 : .....(CMDDAT Xfer Time) > > Rx Data:10 06 02 0a 00 ee 10 03 .. (ACK ) > > Rx Data:10 0e 08 02 0a dc 07 08 00 20 09 ca 10 03 ........ (DATTIM ) > > Tx Data:10 06 02 0e 00 ea 10 03 : .....(ACK ) > > GPS Serial Open at 9600 > > Tx Data:10 0a 02 02 00 f2 10 03 : .....(CMDDAT Xfer Posn) > > Rx Data:10 06 02 0a 00 ee 10 03 .. (ACK ) > > Rx Data:10 11 10 10 dd 1b 32 e2 3a 34 e9 3f d4 c5 93 7c 4f 89 bf 3f bf 10 > > 03 ..2..4......O... (POS ) > > Tx Data:10 06 02 11 00 e7 10 03 : .....(ACK ) > > Waypoint type: 108 > > Chosen waypoint length 10 > > GPS Serial Open at 9600 > > Tx Data:10 0a 02 07 00 ed 10 03 : .....(CMDDAT Xfer Wpt) > > GPS_Packet_Read: No DLE. Data received, but probably not a garmin > packet. > > [ERROR] A100_Get: No acknowledge > > GARMIN:Can't get waypoint from /dev/ttyUSB0 > > > > or with -t: > > > > gpsbabel -D9 -t -i garmin -f /dev/ttyUSB0 -o gpx -F track.gpx > > GPSBabel Version: 1.5.2 > > GPS Serial Open at 9600 > > Tx Data:10 fe 00 02 10 03 : ...(PRDREQ ) > > Rx Data:10 15 02 02 00 e7 10 03 .. (NAK ) > > GARMIN:Can't init /dev/ttyUSB0 > > [AliEnv] mvl@multatuli:~$ gpsbabel -D9 -t -i garmin -f /dev/ttyUSB0 -o > gpx > > -F track.gpx > > GPSBabel Version: 1.5.2 > > GPS Serial Open at 9600 > > Tx Data:10 fe 00 02 10 03 : ...(PRDREQ ) > > Rx Data:10 06 02 fe 00 fa 10 03 .. (ACK ) > > Rx Data:10 ff 85 b3 00 86 01 65 54 72 65 78 20 4c 65 67 65 6e 64 20 53 6f > > 66 74 77 61 72 65 20 56 65 72 73 69 6f 6e 20 33 2e 39 30 00 56 45 52 42 > 4d > > 41 50 20 41 74 6c 61 6e 74 69 63 20 48 69 67 68 77 61 79 20 31 2e 30 30 > 00 > > 56 45 52 53 4d 41 50 20 43 41 4d 45 52 4f 4e 2c 20 41 5a 20 28 57 45 53 > 54 > > 29 2c 20 47 4c 45 4e 20 43 41 4e 59 4f 4e 20 44 41 4d 2c 20 41 5a 20 28 > 57 > > 45 53 54 29 2c 20 47 52 20 30 2e 30 30 00 bb 10 03 > > ....eTrex.Legend.Software.Version.3.90.VERBMAP.Atlantic. > Highway.1.00.VERSMAP.CAMERON..AZ..WEST...GLEN.CANYON.DAM.. > AZ..WEST...GR.0.00. > > (PRDDAT ) > > Tx Data:10 06 02 ff 00 f9 10 03 : .....(ACK ) > > Unit: eTrex Legend Software Version 3.90 > > ID: 179 > > Version: 3.90Rx Data:10 fd 4b 50 00 00 4c 01 00 41 0a 00 41 64 00 44 6c > 00 > > 41 c9 00 44 ca 00 44 6c 00 44 d2 00 41 2d 01 44 36 01 44 2d 01 41 f4 01 > 44 > > f5 01 41 58 02 44 58 02 41 bc 02 44 bc 02 41 20 03 44 20 03 41 22 03 44 > 22 > > 03 41 84 03 41 86 03 41 87 03 a0 10 03 > > P..L..A..Ad.Dl.A..D..Dl.D..A..D6.D..A..D..AX.DX.A..D..A..D.. > A..D..A..A..A.. > > (UNKNOWN ) > > Tx Data:10 06 02 fd 00 fb 10 03 : .....(SESACK ) > > > > Capability A10: > > Capability A100: D108 > > Capability A201: D202 D108 D210 > > Capability A301: D310 D301 > > Capability A500: D501 > > Capability A600: D600 > > Capability A700: D700 > > Capability A800: D800 > > Capability A802: D802 > > Capability A900: > > Capability A902: > > Capability A903: > > Link_type 1 Device_command 0 > > Waypoint: Transfer 100 Type 108 > > Route: Transfer 201 Header 202 Type 108 > > Track: Transfer 301 Type 301 > > Tx Data:10 0a 02 32 00 c2 10 03 : 2....(CMDDAT Xfer PVT Stop) > > Rx Data:10 23 39 00 ff 00 60 12 00 00 00 00 00 00 00 ff ff ff ff ff ff ff > > ff ff ff ff ff 98 af 1b 25 02 b3 b8 03 c0 58 bf 41 51 59 04 69 51 59 04 > 69 > > 20 20 20 20 30 32 39 00 00 00 00 00 00 e7 10 03 > > .................................X.AQY.iQY.i....029...... (WPTDAT ) > > [ERROR] A800_Off: Not acknowledged > > GPS Serial Open at 9600 > > Tx Data:10 0a 02 05 00 ef 10 03 : .....(CMDDAT Xfer Time) > > Rx Data:10 15 02 02 00 e7 10 03 .. (NAK ) > > GPS Serial Open at 9600 > > Tx Data:10 0a 02 02 00 f2 10 03 : .....(CMDDAT Xfer Posn) > > Rx Data:10 06 02 0a 00 ee 10 03 .. (ACK ) > > Rx Data:10 11 10 10 dd 1b 32 e2 3a 34 e9 3f d4 c5 93 7c 4f 89 bf 3f bf 10 > > 03 ..2..4......O... (POS ) > > Tx Data:10 06 02 11 00 e7 10 03 : .....(ACK ) > > Waypoint type: 108 > > Chosen waypoint length 10 > > GPS Serial Open at 9600 > > Tx Data:10 0a 02 06 00 ee 10 03 : .....(CMDDAT Xfer Trk) > > Rx Data:10 23 39 00 ff 00 60 12 00 00 00 00 00 00 00 ff ff ff ff ff ff ff > > ff ff ff ff ff 0e 3a 13 25 08 56 b3 03 00 48 8f 41 51 59 04 69 51 59 04 > 69 > > 20 20 20 20 30 33 31 00 00 00 00 00 00 51 10 03 > > .............................V...H.AQY.iQY.i....031...... (WPTDAT ) > > cet_util: Converting from "US-ASCII" to "UTF-8", done. > > options: module/option=value: gpx/snlen="32" (=default) > > > > ------------ > > > > Let me know if there is anything I can try to fix this; if needed, I > would > > be happy to play a bit with the code, but pointers to where to start > > looking would be helpful. It could be that the UDB-to-serial device is > > flaky; it's definitely old, but has worked in the past. > > > > Best regards, > > > > Marco. > > > ------------------------------------------------------------ > ------------------ > > Check out the vibrant tech community on one of the world's most > > engaging tech sites, SlashDot.org! http://sdm.link/slashdot > > > _______________________________________________ > > Gpsbabel-misc mailing list http://www.gpsbabel.org > > Gps...@li... > > To unsubscribe, change list options, or see archives, visit: > > https://lists.sourceforge.net/lists/listinfo/gpsbabel-misc > > > ------------------------------------------------------------ > ------------------ > Developer Access Program for Intel Xeon Phi Processors > Access to Intel Xeon Phi processor-based developer platforms. > With one year of Intel Parallel Studio XE. > Training and support from Colfax. > Order your platform today.http://sdm.link/intel > _______________________________________________ > Gpsbabel-misc mailing list http://www.gpsbabel.org > Gps...@li... > To unsubscribe, change list options, or see archives, visit: > https://lists.sourceforge.net/lists/listinfo/gpsbabel-misc > |
