[Gc-linux-cvs] linux/drivers/net Kconfig,1.18,1.19 Makefile,1.15,1.16

SourceForge Headquarters 225 Broadway Suite 1600 San Diego, CA 92101 +1 (858) 422-6466

Update of /cvsroot/gc-linux/linux/drivers/net
In directory sc8-pr-cvs1.sourceforge.net:/tmp/cvs-serv10066/drivers/net

Modified Files:
	Kconfig Makefile 
Log Message:
Linux 2.6.15.


Index: Makefile
===================================================================
RCS file: /cvsroot/gc-linux/linux/drivers/net/Makefile,v
retrieving revision 1.15
retrieving revision 1.16
diff -u -d -r1.15 -r1.16

--- Makefile	31 Oct 2005 00:31:02 -0000	1.15
+++ Makefile	18 Jan 2006 23:41:53 -0000	1.16
@@ -13,7 +13,7 @@
 obj-$(CONFIG_BONDING) += bonding/
 obj-$(CONFIG_GIANFAR) += gianfar_driver.o
 
-gianfar_driver-objs := gianfar.o gianfar_ethtool.o gianfar_phy.o
+gianfar_driver-objs := gianfar.o gianfar_ethtool.o gianfar_mii.o
 
 #
 # link order important here
@@ -64,6 +64,7 @@
 obj-$(CONFIG_VIA_RHINE) += via-rhine.o
 obj-$(CONFIG_VIA_VELOCITY) += via-velocity.o
 obj-$(CONFIG_ADAPTEC_STARFIRE) += starfire.o
+obj-$(CONFIG_RIONET) += rionet.o
 
 #
 # end link order section
@@ -111,6 +112,7 @@
 obj-$(CONFIG_PPP_SYNC_TTY) += ppp_synctty.o
 obj-$(CONFIG_PPP_DEFLATE) += ppp_deflate.o
 obj-$(CONFIG_PPP_BSDCOMP) += bsd_comp.o
+obj-$(CONFIG_PPP_MPPE) += ppp_mppe.o
 obj-$(CONFIG_PPPOE) += pppox.o pppoe.o
 
 obj-$(CONFIG_SLIP) += slip.o
@@ -166,6 +168,7 @@
 obj-$(CONFIG_MIPS_JAZZ_SONIC) += jazzsonic.o
 obj-$(CONFIG_MIPS_GT96100ETH) += gt96100eth.o
 obj-$(CONFIG_MIPS_AU1X00_ENET) += au1000_eth.o
+obj-$(CONFIG_MIPS_SIM_NET) += mipsnet.o
 obj-$(CONFIG_SGI_IOC3_ETH) += ioc3-eth.o
 obj-$(CONFIG_DECLANCE) += declance.o
 obj-$(CONFIG_ATARILANCE) += atarilance.o
@@ -202,3 +205,6 @@
 obj-$(CONFIG_ETRAX_ETHERNET) += cris/
 
 obj-$(CONFIG_NETCONSOLE) += netconsole.o
+
+obj-$(CONFIG_FS_ENET) += fs_enet/
+

Index: Kconfig
===================================================================
RCS file: /cvsroot/gc-linux/linux/drivers/net/Kconfig,v
retrieving revision 1.18
retrieving revision 1.19
diff -u -d -r1.18 -r1.19
--- Kconfig	31 Oct 2005 00:31:02 -0000	1.18
+++ Kconfig	18 Jan 2006 23:41:53 -0000	1.19
@@ -456,7 +456,7 @@
 
 config SGI_IOC3_ETH
 	bool "SGI IOC3 Ethernet"
-	depends on NET_ETHERNET && PCI && SGI_IP27 && BROKEN
+	depends on NET_ETHERNET && PCI && SGI_IP27
 	select CRC32
 	select MII
 	help
@@ -484,6 +484,14 @@
 	  the moment only acceleration of IPv4 is supported.  This option
 	  enables offloading for checksums on transmit.  If unsure, say Y.
 
+config MIPS_SIM_NET
+	tristate "MIPS simulator Network device (EXPERIMENTAL)"
+	depends on NETDEVICES && MIPS_SIM && EXPERIMENTAL
+	help
+	  The MIPSNET device is a simple Ethernet network device which is
+	  emulated by the MIPS Simulator.
+	  If you are not using a MIPSsim or are unsure, say N.
+
 config SGI_O2MACE_ETH
 	tristate "SGI O2 MACE Fast Ethernet support"
 	depends on NET_ETHERNET && SGI_IP32=y
@@ -813,7 +821,7 @@
 	tristate "SMC 91C9x/91C1xxx support"
 	select CRC32
 	select MII
-	depends on NET_ETHERNET && (ARM || REDWOOD_5 || REDWOOD_6 || M32R || SUPERH)
+	depends on NET_ETHERNET && (ARM || REDWOOD_5 || REDWOOD_6 || M32R || SUPERH || SOC_AU1X00)
 	help
 	  This is a driver for SMC's 91x series of Ethernet chipsets,
 	  including the SMC91C94 and the SMC91C111. Say Y if you want it
@@ -1164,38 +1172,74 @@
 	  be called ibmveth.
 
 config IBM_EMAC
-	bool "IBM PPC4xx EMAC driver support"
+	tristate "PowerPC 4xx on-chip Ethernet support"
 	depends on 4xx
-	select CRC32
-	---help---
-	  This driver supports the IBM PPC4xx EMAC family of on-chip
-	  Ethernet controllers.
-
-config IBM_EMAC_ERRMSG
-	bool "Verbose error messages"
-	depends on IBM_EMAC && BROKEN
+	help
+	  This driver supports the PowerPC 4xx EMAC family of on-chip
+          Ethernet controllers.
 
 config IBM_EMAC_RXB
 	int "Number of receive buffers"
 	depends on IBM_EMAC
-	default "128" if IBM_EMAC4
-	default "64"
+	default "128"
 
 config IBM_EMAC_TXB
 	int "Number of transmit buffers"
 	depends on IBM_EMAC
-	default "128" if IBM_EMAC4
-	default "8"
+	default "64"
 
-config IBM_EMAC_FGAP
-	int "Frame gap"
+config IBM_EMAC_POLL_WEIGHT
+	int "MAL NAPI polling weight"
 	depends on IBM_EMAC
-	default "8"
+	default "32"
 
-config IBM_EMAC_SKBRES
-	int "Skb reserve amount"
+config IBM_EMAC_RX_COPY_THRESHOLD
+	int "RX skb copy threshold (bytes)"
+	depends on IBM_EMAC
+	default "256"
+
+config IBM_EMAC_RX_SKB_HEADROOM
+	int "Additional RX skb headroom (bytes)"
 	depends on IBM_EMAC
 	default "0"
+	help
+	  Additional receive skb headroom. Note, that driver
+	  will always reserve at least 2 bytes to make IP header
+	  aligned, so usualy there is no need to add any additional
+	  headroom.
+	  
+	  If unsure, set to 0.
+
+config IBM_EMAC_PHY_RX_CLK_FIX
+	bool "PHY Rx clock workaround"
+	depends on IBM_EMAC && (405EP || 440GX || 440EP || 440GR)
+	help
+	  Enable this if EMAC attached to a PHY which doesn't generate
+	  RX clock if there is no link, if this is the case, you will 
+	  see "TX disable timeout" or "RX disable timeout" in the system
+	  log.
+	  
+	  If unsure, say N.
+
+config IBM_EMAC_DEBUG
+	bool "Debugging"
+	depends on IBM_EMAC
+	default n
+
+config IBM_EMAC_ZMII
+	bool
+	depends on IBM_EMAC && (NP405H || NP405L || 44x)
+	default y
+
+config IBM_EMAC_RGMII
+	bool
+	depends on IBM_EMAC && 440GX
+	default y
+		
+config IBM_EMAC_TAH
+	bool
+	depends on IBM_EMAC && 440GX
+	default y
 
 config NET_PCI
 	bool "EISA, VLB, PCI and on board controllers"
@@ -1776,6 +1820,7 @@
 	  controller on the Renesas H8/300 processor.
 
 source "drivers/net/fec_8xx/Kconfig"
+source "drivers/net/fs_enet/Kconfig"
 
 endmenu
 
@@ -2092,6 +2137,7 @@
 config GIANFAR
 	tristate "Gianfar Ethernet"
 	depends on 85xx || 83xx
+	select PHYLIB
 	help
 	  This driver supports the Gigabit TSEC on the MPC85xx 
 	  family of chips, and the FEC on the 8540
@@ -2201,8 +2247,8 @@
 	depends on PCI
 	---help---
 	  This driver supports the 10Gbe XFrame NIC of S2IO. 
-	  For help regarding driver compilation, installation and 
-	  tuning please look into ~/drivers/net/s2io/README.txt.
+	  More specific information on configuring the driver is in 
+	  <file:Documentation/networking/s2io.txt>.
 
 config S2IO_NAPI
 	bool "Use Rx Polling (NAPI) (EXPERIMENTAL)"
@@ -2221,17 +2267,6 @@
 
 	  If in doubt, say N.
 
-config 2BUFF_MODE
-	bool "Use 2 Buffer Mode on Rx side."
-	depends on S2IO
-	---help---
-	On enabling the 2 buffer mode, the received frame will be
-	split into 2 parts before being DMA'ed to the hosts memory.
-	The parts are the ethernet header and ethernet payload. 
-	This is useful on systems where DMA'ing to to unaligned 
-	physical memory loactions comes with a heavy price.
-	If not sure please say N.
-
 endmenu
 
 if !UML
@@ -2252,6 +2287,20 @@
 	tristate "iSeries Virtual Ethernet driver support"
 	depends on PPC_ISERIES
 
+config RIONET
+	tristate "RapidIO Ethernet over messaging driver support"
+	depends on NETDEVICES && RAPIDIO
+
+config RIONET_TX_SIZE
+	int "Number of outbound queue entries"
+	depends on RIONET
+	default "128"
+
+config RIONET_RX_SIZE
+	int "Number of inbound queue entries"
+	depends on RIONET
+	default "128"
+
 config FDDI
 	bool "FDDI driver support"
 	depends on (PCI || EISA)
@@ -2483,6 +2532,19 @@
 	  module; it is called bsd_comp and will show up in the directory
 	  modules once you have said "make modules". If unsure, say N.
 
+config PPP_MPPE
+       tristate "PPP MPPE compression (encryption) (EXPERIMENTAL)"
+       depends on PPP && EXPERIMENTAL
+       select CRYPTO
+       select CRYPTO_SHA1
+       select CRYPTO_ARC4
+       ---help---
+         Support for the MPPE Encryption protocol, as employed by the
+	 Microsoft Point-to-Point Tunneling Protocol.
+
+	 See http://pptpclient.sourceforge.net/ for information on
+	 configuring PPTP clients and servers to utilize this method.
+
 config PPPOE
 	tristate "PPP over Ethernet (EXPERIMENTAL)"
 	depends on EXPERIMENTAL && PPP



