Menu
▾
▴
Re: [Emc-users] hal_motenc - Unable to handle kernel NULL pointerdereference
|
From: Marc B. <mar...@em...> - 2006-08-28 18:09:35
|
Hello It's me again. I have to update and correct my last statement, I changed too many things at once, without being able to locate the error. But now I found the following: It was neither the changed slot nor the card not placed careful enough, it seems to be the card id set to zero what causes the NULL Pointer dereference. But why is this? Is there an explanation? I do not assume there are other people who are not able to use their motenc lite card at id=0. I have only one card so this should work. And why did it work with emc 2.0.3, but not with 2.0.2(1)? and the CVS version? I am clueless, but as far as it seems to work this is ok for me. Thanks for helping again. Marc After I wrote Am Montag, den 28.08.2006, 19:45 +0200 schrieb Marc Bodmer: > Hello Supporters > > Thank you very much for the feedback. > With this help I was put in the right direction. > > I took the card out of the pci slot and checked the jumpers. > They were set correctly. So I put it back into another pci slot. > The same time I changed it's positionn with the ethernet card. > > After this the motenc card worked again, and still works back in > the old slot. > > So probably I just put the card not careful enough, even when > it looked to fit well before I took the card out. > > Sorry for asking a question like this, but thanks very much! > Like this I was able to locate the problem very fast. > > Wish everybody a nice evening... or whatever respective daytime :-) > > regards > Marc > > > > Am Montag, den 28.08.2006, 07:58 -0700 schrieb Dave Engvall: > > On Aug 27, 2006, at 10:12 PM, Stephen Wille Padnos wrote: > > > > > Mark Pictor wrote: > > > > > >> The pdf I saw says nothing about id 3. Here's what it says: > > >> > > >> Header J7: > > >> Pin 1: Reserved > > >> Pin 3: Board ID 0 > > >> Pin 5: Board ID 1 > > >> Pins 2,4, and 6 are tied to Ground. > > >> > > >> > > > I suspect those are ID bit 0 and ID bit 1. Bit 0 has a weight of > > > 1, and > > > bit 1 has a weight of 2. Jumpering the pin (3 or 5) to ground causes > > > that ID bit to be 0, and leaving it open causes that bit to be 1. So, > > > if no jumpers are installed, bits 0 and 1 are both 1, and the > > > binary ID > > > is 11 which is 3 decimal. > > > > > > Stick jumpers on those two locations (3->4 and 5->6), and the ID > > > will be > > > 0 as expected. > > > > Exactly: check /var/log/syslog for conformation of the ID. > > > > > > - Steve > > > > > > > > > ---------------------------------------------------------------------- > > > --- > > > Using Tomcat but need to do more? Need to support web services, > > > security? > > > Get stuff done quickly with pre-integrated technology to make your > > > job easier > > > Download IBM WebSphere Application Server v.1.0.1 based on Apache > > > Geronimo > > > http://sel.as-us.falkag.net/sel? > > > cmd=lnk&kid=120709&bid=263057&dat=121642 > > > _______________________________________________ > > > Emc-users mailing list > > > Emc...@li... > > > https://lists.sourceforge.net/lists/listinfo/emc-users > > > > ------------------------------------------------------------------------- > > Using Tomcat but need to do more? Need to support web services, security? > > Get stuff done quickly with pre-integrated technology to make your job easier > > Download IBM WebSphere Application Server v.1.0.1 based on Apache Geronimo > > http://sel.as-us.falkag.net/sel?cmd=lnk&kid=120709&bid=263057&dat=121642 > > _______________________________________________ > > Emc-users mailing list > > Emc...@li... > > https://lists.sourceforge.net/lists/listinfo/emc-users > > > ------------------------------------------------------------------------- > Using Tomcat but need to do more? Need to support web services, security? > Get stuff done quickly with pre-integrated technology to make your job easier > Download IBM WebSphere Application Server v.1.0.1 based on Apache Geronimo > http://sel.as-us.falkag.net/sel?cmd=lnk&kid=120709&bid=263057&dat=121642 > _______________________________________________ > Emc-users mailing list > Emc...@li... > https://lists.sourceforge.net/lists/listinfo/emc-users |