Menu
▾
▴
[Dri-users] drmSetBusid failed on ATI Radeo Mobility M6 LY
|
From: M. G. <xa...@cs...> - 2002-11-27 19:42:54
|
Hi,
I have a Dell Latitude 610,
I'm running linux-2.4.19 (plain), Debian/sid (=unstable), updated
today.
/dev/dri is mode 755.
Just to get sure, busmastering was set on with setpci -s 01:00.0 4.w
The output of lspci -s 01:00.0 is
=====
01:00.0 VGA compatible controller: ATI Technologies Inc Radeon Mobility M6 LY (prog-if 00 [VGA])
Subsystem: Dell Computer Corporation: Unknown device 00e3
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop+ ParErr- Stepping+ SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (2000ns min), cache line size 08
Interrupt: pin A routed to IRQ 11
Region 0: Memory at e0000000 (32-bit, prefetchable) [size=128M]
Region 1: I/O ports at c000 [size=256]
Region 2: Memory at fcff0000 (32-bit, non-prefetchable) [size=64K]
Expansion ROM at <unassigned> [disabled] [size=128K]
Capabilities: [58] AGP version 2.0
Status: RQ=47 SBA+ 64bit- FW- Rate=x1,x2,x4
Command: RQ=0 SBA+ AGP- 64bit- FW- Rate=<none>
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
=====
My XFree86 configuration is
=====
Section "Module"
Load "dbe"
Load "GLcore"
Load "bitmap"
Load "dbe"
Load "ddc"
Load "glx"
Load "dri"
Load "extmod"
Load "int10"
Load "record"
Load "speedo"
Load "vbe"
SubSection "extmod"
# Option "omit xfree86-dga" # don't initialise the DGA extension
EndSubSection
Load "type1"
Load "freetype"
EndSection
[...]
Section "Device"
Identifier "Radeon"
VendorName "ATI"
Driver "ati"
#Driver "radeon"
#Option "AGPMode" "4"
#Driver "fbdev"
BusID "PCI:01:0:0"
#VideoRam 16384
EndSection
Section "DRI"
Mode 0666
EndSection
=====
I tried radeon-20021022-linux.i386.tar.bz2.
X wouldn't start without the new libxaa.a. Since DRI wasn't working
Just to get sure I also tried the whole extra-package. Still DRI
didn't work.
After that I deinstalled the dripgk, restored my original X-libraries
and -executables and tried radeon-20021127-linux.i386.tar.bz2
X didn't start (version mismatch), so I installed the extras package.
X works, but DRI still doesn't ...
Then I tried to change DefaultColourDepth from 16 to 24, no change.
The interesting part in the XFree86 log (it's always the same error):
=====
XFree86 Version 4.2.99.2 (DRI trunk) / X Window System
(protocol Version 11, revision 0, vendor release 6600)
Release Date: 21 October 2002
[...]
(II) RADEON(0): vgaHWGetIOBase: hwp->IOBase is 0x03d0, hwp->PIOOffset is 0x0000
(II) RADEON(0): PCI bus 1 card 0 func 0
(**) RADEON(0): Depth 16, (--) framebuffer bpp 16
(II) RADEON(0): Pixel depth = 16 bits stored in 2 bytes (16 bpp pixmaps)
(==) RADEON(0): Default visual is TrueColor
(**) RADEON(0): Option "AGPMode" "4"
(==) RADEON(0): RGB weight 565
(II) RADEON(0): Using 6 bits per RGB (8 bit DAC)
(II) Loading sub module "int10"
(II) LoadModule: "int10"
(II) Reloading /usr/X11R6/lib/modules/linux/libint10.a
(II) RADEON(0): initializing int10
(II) RADEON(0): Primary V_BIOS segment is: 0xc000
(--) RADEON(0): Chipset: "ATI Radeon Mobility LY (AGP)" (ChipID = 0x4c59)
(--) RADEON(0): Linear framebuffer at 0xe0000000
(--) RADEON(0): MMIO registers at 0xfcff0000
(--) RADEON(0): VideoRAM: 16384 kByte (64-bit DDR SDRAM)
(II) RADEON(0): Primary Display == Type 2
(II) RADEON(0): Panel ID string: 1024x768
(II) RADEON(0): Panel Size from BIOS: 1024x768
[...]
(II) Reloading /usr/X11R6/lib/modules/libvbe.a
(II) RADEON(0): VESA BIOS detected
(II) RADEON(0): VESA VBE Version 2.0
(II) RADEON(0): VESA VBE Total Mem: 16384 kB
(II) RADEON(0): VESA VBE OEM: ATI MOBILITY RADEON
(II) RADEON(0): VESA VBE OEM Software Rev: 1.0
(II) RADEON(0): VESA VBE OEM Vendor: ATI Technologies Inc.
(II) RADEON(0): VESA VBE OEM Product: R100
(II) RADEON(0): VESA VBE OEM Product Rev: 01.00
(II) LoadModule: "ddc"
(II) Reloading /usr/X11R6/lib/modules/libddc.a
(II) RADEON(0): VESA VBE DDC supported
(II) RADEON(0): VESA VBE DDC Level none
(II) RADEON(0): VESA VBE DDC transfer in appr. 2 sec.
(II) RADEON(0): VESA VBE DDC read failed
(==) RADEON(0): Write-combining range (0xe0000000,0x1000000)
(II) RADEON(0): PLL parameters: rf=2700 rd=60 min=12000 max=35000; xclk=16600
(==) RADEON(0): Using gamma correction (1.0, 1.0, 1.0)
(--) RADEON(0): Virtual size is 1024x768 (pitch 1056)
(**) RADEON(0): Mode "1024x768"
(**) RADEON(0): Mode "800x600"
(==) RADEON(0): DPI set to (75, 75)
(II) Loading sub module "xaa"
(II) LoadModule: "xaa"
(II) Loading /usr/X11R6/lib/modules/libxaa.a
(II) Module xaa: vendor="The XFree86 Project"
compiled for 4.2.99.2, module version = 1.1.0
ABI class: XFree86 Video Driver, version 0.6
(**) RADEON(0): Using AGP 4x mode
(II) RADEON(0): AGP Fast Write disabled by default
(II) Loading sub module "shadow"
(II) LoadModule: "shadow"
(II) Loading /usr/X11R6/lib/modules/libshadow.a
(II) Module shadow: vendor="The XFree86 Project"
compiled for 4.2.1.1, module version = 1.0.0
ABI class: XFree86 ANSI C Emulation, version 0.1
(**) RADEON(0): Disabling page flipping
(!!) RADEON(0): For information on using the multimedia capabilities
of this adapter, please see http://gatos.sf.net.
[...]
(==) RADEON(0): Write-combining range (0xe0000000,0x1000000)
drmOpenDevice: minor is 0
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 7, (OK)
drmOpenDevice: minor is 0
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 7, (OK)
drmOpenDevice: minor is 0
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 7, (OK)
drmGetBusid returned ''
(II) RADEON(0): [drm] drmSetBusid failed (7, PCI:1:0:0), Permission denied
(EE) RADEON(0): [dri] DRIScreenInit failed. Disabling DRI.
(II) RADEON(0): Memory manager initialized to (0,0) (1056,7943)
[...]
(II) RADEON(0): Acceleration enabled
(II) RADEON(0): Using hardware cursor (scanline 770)
(II) RADEON(0): Largest offscreen area available: 1056 x 7171
(II) RADEON(0): Direct rendering disabled
=====
The interesting part is obviously:
"(II) RADEON(0): [drm] drmSetBusid failed (7, PCI:1:0:0),
Permission denied"
Can anybody help me?
I tried to google for "drmSetBusid" errors, but I found no solution
for the problem!
greetings max
PS: this is the second try to install the DRI drivers. I tried it
about half a year ago, and it was the same problem (but back
then I was also trying to use GATOS).
|