Activity for CrazyScan
-
CrazyScan updated /test/StreamReaderExEx-BDA.rar
-
Abo Hamdy posted a comment on discussion General Discussion
Thanks
-
CrazyCat posted a comment on discussion General Discussion
https://sourceforge.net/p/crazyscan/wiki/Info/ Si2183 and M88RS6060-based cards support BLScan2 ans DVB-S2X
-
@crazycat69 What are the best cards in blscan2 and support S2X?
-
Marco modified a comment on discussion General Discussion
Thanks to all. For bdadvb2, I can confirm that my card has somethimes problems in blindscan2 mode, probably related to low symbol rate. For Crazycat, I also tried the latest streamreader (1.2.5.198). Hope you could do some test with a SiLabs based device in order to find a solution. If you need my help do not esitate to ask!
-
Thanks to all. For bdadvb2, I can confirm that my card has somethimes problems in blindscan2 mode, probably related to low symbol rate. For Crazycat, I also try the latest streamreader (1.2.5.198). Hope you could do some test with a SiLabs based device in order to find a solution. If you need my help do not esitate to ask!
-
Thanks to all. For bdadvb2, I can confirm that my card has somethimes problems in blindscan2 mode, probably related to low symbol rate. For Crazycat, I used the latest streamreader (1.2.5.198). Hope you could do some test with a SiLabs based device in order to find a solution. If you need my help do not esitate to ask!
-
try latest test build StreamReaderEx-BDA + CrazyScan https://sourceforge.net/projects/crazyscan/files/test/
-
bdadvb2 posted a comment on discussion General Discussion
6590 as any other SiLabs based device might run into problems on low SR frequencies - finding the same frequency on and on. On your screenshot it is visible that 11205H is detected multiple times (number overlapping each other). Check 11250-11400 and then 11200-11250. Check LED on the card - probably flashing on and off in regular periods.
-
mystical case :)
-
Hi CrazyCat, hope you can help me to understand why Crazyscan (last version 1.02.185) with my Tbs 6590 completely blocked while scanning in blindscan2 mode MonacoSat 52 east between 11.200 and 11.400 H. There must be some signal that make the app crash. Ebs pro crash the same. Best regards
-
Hi Crazycat, hope you can help me to understand why Crazyscan (last version 1.02.185) with my Tbs 6590 completely blocked while scanning in blindscan2 mode MonacoSat 52 east between 11.200 and 11.400 H. There must be some signal that make the app crash. Ebs pro crash the same. Best regards
-
TBS 6902 with TAS2101 or GX1133 demod chip ?
-
Rupert modified a comment on discussion General Discussion
Hi Would anyone please be able to help me to resolve the error message of "PLSSel failed !" when starting a blind scan? I am using a TBS6902 card with the latest version of streamreader and CrazyScan version v1.0.2.190 with Win10 Pro as O/S. The scan part runs OK and gives a spectrum but the eror message appears as soon as I start the blind scan. The error occurs with both BlindScan and BlindScan2 modes. Thank you
-
Hi Would anyone please be able to help me to resolve the error message of "PLSSel failed !" when starting a blind scan? I am using a TBS6902 card with the latest version of streamreader and CrazyScan version v1.0.2.190 with Win10 Pro as O/S. The scan part runs OK and gives a spectrum but the eror message appears as soon as I start the blind scan. Thank you
-
@CrazyCat What are the best cards in blscan2 and support S2X?
-
no way :)
-
@crazycat69 What about BLScan2 in TBS6909-x v2 card is there a solution??
-
DVB TS over IP multicast over GSE (or some similar encapsulation). Software extract TS packets from BBFrame traffic (some packets fit to fragmented GSE packets and ""dropped)
-
Tomasz modified a comment on discussion General Discussion
i have tbs 6983 and i got the best picture with transedit tool, dvbviewer should work the same. For 101k packets only 70 dropped. Picture is very good only sometimes you can see pixelated little frame, If i use any crazyscan, ebs pro or any other tool which use streamreader situation got worse. 100k packets and 4469 dropped, video and audio is chopping. im talking about the same bfbs freq on 15W. https://www.satellites.co.uk/forums/threads/16apsk-signal-15w-why-cant-i-scan-it.181745/page-2#post-1158352...
-
i have tbs 6983 and i got the best picture with transedit tool, dvbviewer should work the same. For 101k packets only 70 dropped picture is very good only sometimes you can see pixelated little frame, If i use any crazyscan, ebs pro or any other tool which use streamreader situation got worse. 100k packets and 4469 dropped, video and audio is chopping. im talking about the same bfbs freq on 15W. https://www.satellites.co.uk/forums/threads/16apsk-signal-15w-why-cant-i-scan-it.181745/page-2#post-1158352...
-
i have tbs 6983 and i got the best picture with transedit, dvbviewer should work the same. For 101k packets only 70 dropped picture is very good only sometimes you can see pixelated little frame, If i use any crazyscan, ebs pro or any other tool which use streamreader situation got worse. 100k packets and 4469 dropped, video and audio is chopping. im talking about the same bfbs freq on 15W.
-
The bitrate problem has already been fixed. (Thanxs) The very slow blind search problem remains. With the use of ranges the search time takes ten minutes, without ranges the search time is very long, exceeding half an hour.
-
try latest StreamReaderEx-BDA test build Bitrate report from STiD135 BLScan2() fixed
-
try latest StreamReaderEx-BDA test build
-
-
So do you have a solution for the BLScan2 problem in the tbs6909-x v2 card and not reading the frequencies and bitrate correctly?
-
ACM/VCM is adaptive/variable coding modulation, next level DVB-S2/S2X stream type. So we have different processing streams in demods.
-
But TBS says the card supports ACM.
-
No solution, for 6903x/6909x this normal behavior.
-
These frequencies are received directly on other cards.
-
This card does not support BLScan2 fast search. I used the latest Stream Reader and with Ranges it exceeds ten minutes. Is there a solution?
-
For 6903x/6909x this normal behavior.
-
The signal is very good but the channels are not working
-
If you have time, join AnyDesk with me and try it yourself and see. 294 741 335
-
I did not understand what you asked well. I am facing a problem in not working these frequencies on my TBS6909-x v2 card, and it is supposed to support ACM. What can I do to make these frequencies work on my card?
-
Ok, look like my 6983 and 6903x see it, some data in generic continous stream. And some DVB TS encapsulated in IP multicast traffic over this GCS stream.
-
5930, 5530 have restricted support ACM/VCM. But just true extract TS packets from frames - so you have some corrupted TS. Same on STV0900, STV0910 based cards (6983, 6903, 6908, 5927). STiD135 based card output BBFrames or extracted GSE packets encapsulated in PUSI TS (PID 270 or 280).
-
5930, 5530 have restricted support ACM/VCM. But just true extract TS packets from frames - so you have some corrupted TS. Same on STV0900, STV0910 based cards (6983, 6903, 6908, 5927). STiD135 based card output BBFrames or extracted GSE packets encapsulated in PUSI TS (PID 270 or 280).
-
5930, 5530 have restricted support ACM/VCM. But just true extract TS packets from frames - so you have some corrupted TS. Same on STV0900, STV0910 based cards (6983, 6903, 6908, 5927). STiD135 based card output BBFrames or extracted GSE packets incapsulated to PUSI TS (PID 270 or 280).
-
5930, 5530 have restricted support ACM/VCM. But just true extract TS packets from frames - so you have some corrupted TS. Same on STV0900, STV0910 based cards (6983, 6903, 6908, 5927). STiD135 based card output BBFrames or extracted GSE packets incapsulated to PUSI TS (PID 270 or 280).
-
5530 have restricted support ACM/VCM. But just true extract TS packets from frames - so you have some corrupted TS. Same on STV0900, STV0910 based cards (6983, 6903, 6908, 5927). STiD135 based card output BBFrames or extracted GSE packets incapsulated to PUSI TS (PID 270 or 280).
-
These frequencies are easily picked up on the TBS5530 card, although it does not support ACM, but with image interruptions, as is clear in the pictures, while the 6909-x card, which is supposed to support ACM, does not pick up the channels, despite the presence of the signal.
-
Ok, look like my 6983 and 6903x see it, some data in generic continous stream. And some DVB TS incapsulated in IP multicast traffic over this GCS stream.
-
Maybe not default PLS code ? Default Gold 0 or Root 1
-
Egypt
-
The frequency signal is strong, exceeding 14.5 dB.
-
what your location ? https://www.flysat-beams.com/telstar12v-beam.php
-
I have the latest Stream Reader dated 13-9-2024 and also the latest card driver on Windows
-
Hello, I have a TBS6909-x v2 card and it is supposed to support ACM frequencies, but when I tried it on the Telstar 12 Vantage @ 15° W satellite on the British Army BFBS package frequencies that work with ACM technology, the card does not read the frequencies and I cannot enjoy this package on this card, in addition to the fact that this card does not support BLScan2 and takes a very long time to search. What is the solution then??
-
Satlinea posted a comment on discussion General Discussion
You can order it here: https://www.tbsiptv.com/tbs5930-lite-dvb-s2-or-s-universal-tv-tuner-usb-card I got it and it works very well
-
fusillo posted a comment on discussion General Discussion
i ordered the 5930 non lite and I returned it back
-
Hello CrazyCat and everyone here I would like to ask here for another bug found in CrazyScan. dbm value doesn't match printed spectrum in CrazyScan, its different than reported by StreamReader example: 12572 V 7200 streamreader report -44dbm but on spectrum it shows -46dBm. This behaviour is okay?
-
Hello i would like to ask here for another bug found in crazyscan. dbm value doesn't match printed spectrum in CrazyScan, its different than reported by StreamReader example: 12572 V 7200 streamreader report -44dbm but on spectrum it shows -46dBm. This behaviour is okay?
-
Massimo posted a comment on discussion General Discussion
Hello, I tried to buy a TBS5930-lite but the "Buy button" always send me to the 5930 non lite version. @fusillo how did you ordered this card? (come hai fatto a ordinarla?)
-
Or right-click on the CrazyScan shortcut, select Properties, go to Compatibility tab, select there to change high DPI settings - then change will apply to this one app only, not the whole OS. CrazyScan is based on Qt4 which was not yet DPI-aware. Not sure if there's any other simple way to improve this than move to at least Qt5, which might be a quite complex task for crazycat (especially having in mind that CrazyScan uses also qwt). I tried once to build CrazyScan with Qt5 on my own, but finally...
-
Try lower this option at display setting to 100%, this should help but will make icons and other stuff very small.
-
Try lower this option to 100%, this should help but will make icons and other stuff very small.
-
Solarpoweredwok posted a comment on discussion General Discussion
Hi Crazycat, wondering if crazyscan has been tested on 4K graphics and monitor. Gettng the following issue ..see screen shot.
-
My Mistake Crazycat, I am confusing the 6903 with the 6903X...Why they name them so similar with different chip is beyond me. The 6903 is no longer available and it is the X version that is that is has a hopelessly slow blind scan . UPDATE: 18/9/24 The TBS5927 USB is the only TBS product being sold that uses the STV0910 chip that the TBS6983 uses. I note too the specs for the SR of theTBS5927 goes from 0.2 to 45Msps which is good for low sr's too. It only has 1 Tuner and is USB unfortunately. But...
-
My Mistake Crazycat, I am confusing the 6903 with the 6903X...Why they name them so similar with different chip is beyond me. The 6903 is no longer available and it is the X version that is that is has a hopelessly slow blind scan . I am wondering if the currently sold 5927 USB is the only TBS product being sold that uses the STV0910 chip that the 6983 uses. I note too the SR of the current 5927 goes from 0.2 to 45Msps which is good for low sr's too. Your thoughts and if any issues with blind scan...
-
You can test 6903 with latest StreamReader ?
-
I discovered the TBS 6983 in Crazyscan carrier search Bscan finds the TP OK, its just unreliable in RF then Bscan2. Screen shots shown. As for the TBS6902 card I cannot get any of the 3 TP's to show by any method in crazyscan even though Direct tune 4196MHz Sr 1415 did but not the lower SR's. As for ebspro with Bscan2 unticked for BScan mode, it is slow and will scan OK but again not showing any of the 3 TP's in question but will show other TP's OK.
-
Ahh OK. Using a TBS6983 card Crazyscan, Bscan2 however will find the transponders with a step of 0.1MHz and span of 4100-4200MHz but unstable sometime 2 TP's 4195 and 4196 and othertimes 1 TP 4198MHz. Trying Direct tune by unticking BScan in carrier search, setting SR manually to TP SR. IT found the TP OK. So Direct Tune worked.
-
I see on the Wiki here the TBS 6903 uses the same Chips set base as the old favourite 6983 yet the 6903 is very very very slow at doing a blind scan. Why is this ?
-
I see on the Wiki here the TBS 6903 uses the same Chips set base as the olf favourite 6983
-
Here is a TBS6902 result of a Direct Tune with Ebspro on one of the Low SR TP's 4196H SR 1415. To show Direct Tune works on this card but streamreader in BScan or BScan2 mode does not for this TP. The other 2 TPs at SR 520 and 400 would not tune.
-
I discovered the TBS 6963 in Crazyscan carrier search Bscan finds the TP OK, its just unreliable in RF then Bscan2. Screen shots shown. As for the TBS6902 card I cannot get any of the 3 TP's to show by any method in crazyscan even though Direct tune 4196MHz Sr 1415 did but not the lower SR's. As for ebspro with Bscan2 unticked for BScan mode, it is slow and will scan OK but again not showing any of the 3 TP's in question but will show other TP's OK.
-
Ahh OK. Using a TBS6963 card Crazyscan, Bscan2 however will find the transponders with a step of 0.1MHz and span of 4100-4200MHz but unstable sometime 2 TP's 4195 and 4196 and othertimes 1 TP 4198MHz. Trying Direct tune by unticking BScan in carrier search, setting SR manually to TP SR. IT found the TP OK. So Direct Tune worked.
-
Ahh OK. Using a TBS6963 card Crazyscan, Bscan2 however will find the transponders with a step of 0.1MHz and span of 4100-4200MHz but unstable sometime 2 TP's 4195 and 4196 and othertimes 1 TP 4198MHz. Trying Direct tune by unticking BScan in carrier search, setting min SR manually at 100. Step and ALL other params are greyed out, Shifting up and down by a few 100 KHZ in Freq cannot tune any of the 3 TP's and setting other known strong TP's it cannot tune either. Direct scan not working. Signal test...
-
Here is a TBS6902 result of a Direct Tune with Ebspro on one of the Low SR TP's 4196H SR 1415. To show Direct Tune works on this card but streamreader in BScan or BScan2 mode does not for this TP.
-
Here are results using a TBS6963. 1. 2 TP's detected of the 3. 2. 3rd TP found using BScan2 of Carrier Search, setting min SR to 100KHz . 3. Direct tune in Carrier Search not finding any TP, even others easily found so This method FAILS. As for the TBS6902 card I cannot get any of the 3 TP's to show by any method in crazyscan even though ebspro using Direct Tune in Signal Analyzer CAN find each of the 3 TP's but BS mode cannot using epsilon 250KHz step. So latest mod streamreader not quite right...
-
Here are results using a TBS6963. 1. 2 TP's detects of the 3. 2. 3rd TP found using BScan2 of Carrier Search, setting min SR to 100KHz . 3. Direct tune in Carrier Search not finding any TP, even others easily found so This method FAILS. As for the TBS6902 card I cannot get any of the 3 TP's to show by any method in crazyscan even though ebspro using Direct Tune in Signal Analyzer CAN find each of the 3 TP's but BS mode cannot using epsilon 250KHz step. So latest mod streamreader not quite right for...
-
Ahh OK. Using a TBS6963 card Crazyscan will not scan with Bscan2 UNTICKED for any transponder on main screen so BScan not working for any TP. It just does not scan. Bscan2 however will find the transponders with a step of 0.1MHz and span of 4100-4200MHz but unstable sometime 2 TP's 4195 and 4196 and othertimes 1 TP 4198MHz. Trying Direct tune by unticking Bscan in carrier search, setting min SR manually at 100. Step and ALL other params are greyed out, Shifting up and down by a few 100 KHZ in Freq...
-
Ahh OK. Using a TBS6963 card Crazyscan will not scan with Bscan2 UNTICKED for any transponder on main screen so BScan not working for any TP. It just does not scan. Bscan2 however will find the transponders with a step of 0.1MHz and span of 4100-4200MHz but unstable sometime 2 TP's 4195 and 4196 and othertimes 1 TP 4198MHz. Trying Direct tune by unticking Bscan in carrier search, setting min SR manually at 100. Step and ALL other params are greyed out, Shifting up and down by a few 100 KHZ in Freq...
-
Ahh OK. Using a TBS6963 card Crazyscan will not scan with Bscan2 UNTICKED for any transponder on main screen so BScan not working for any TP. It just does not scan. Bscan2 however will find the transponders with a step of 0.1MHz and span of 4100-4200MHz but unstable sometime 2 TP's 4195 and 4196 and othertimes 1 TP 4198MHz. Trying Direct tune by unticking Bscan in carrier search, setting min SR manually at 100. Step and ALL other params are greyed out, Shifting up and down by a few 100 KHZ in Freq...
-
Ahh OK. Why don't BScan work with my TBS6902, yet BScan2 does (Excluding the 3 TP's we are discussing). Scan starts at the start freq but don't actually scan, so never completes scan. Direct scan in Carrier search with Bscan unticked sr manually set to min =100 and also cannot find the 3 TP's in question. 4195, 4196 and 4198MHz on the 6902 despite shifting up and down a few 100 KHz. Yet ALTDVB has no problems tuning all 3. TP's. Using a TBS6963 card there is more success. however, why is Bscan2 random,...
-
Ordered the TBS5930lite from China to Italy card + shipping + VAT + import = €111,26 TBS5930lite: 52,63€ shipping: 33€ Vat + import :25.73€ soon it should arrive, if I need it can I contact you? Thanks CrazyCat
-
Ordered the TBS5930lite from China to Italy card + shipping + Taxes + import = €111,26 TBS5930lite: 52,63€ shipping: 33€ Taxes + import :25.73€ soon it should arrive, if I need it can I contact you? Thanks CrazyCat
-
This is not Direct Tune. Run only RFScan, click on graph to open Carrier search and Constellation monitoring, untick Blind Scan marked with red, put all parameters manually and lock with aquarium/fishes/cat icon.
-
Unticking BlindScan2 in top ribbon of crazyscan 190 with updated test streamreader files then initiating BS after RF scan puts the start frq top left on RF scan plot and thats it. Never finds any transponder, never finishes. So Direct access not working on my TBS6902. Carrier search in same boat when unticked BS2 and sr set to 200
-
Unticking BlindScan2 in top ribbon of crazyscan 190 with updated test streamreader files then initiating BS after RF scan puts the start frq top left on RF scan plot and thats it. Never finds any transponder, never finishes. So Direct access not working on my TBS602. Carrier search in same boat when unticked BS2 and sr set to 200
-
Try direct tune in CrazyScan (disable blindscan checkbox and enter SR) MinSR params ignored for GX113x BLScan implementation (look like used on,y for STm demods)
-
Hi Crazycat, PART RESULTS OF TEST FILE. Remote PC offline atm to test on the 6983 card will test tomorrow as he is asleep now :) However see my comment below re Carrier search issue. Now, Testing with my 6902 showed no change in crazyscan. No TP's 4195, 4196 and 4198 show up. Using manually the Carrier search/constellation it too could not find any of the TP's in question. I've note the Carrier search is still a min of 1M for SR and search range. Can we drop them both to 100KHz. Cheers
-
Hi Crazycat, Yes, however same specs for SR on a TBS6983 as is the TBS6902 for the low end. My remote in testing of the TBS6983 fit tunes and locks all 3 close TPs in ALTDVB and DVBDREAM in BDA mode. However in Crazyscan sometimes 1TP of the 3 comes up, other time 2 of them but never 3. So something is slightly a miss. Hopefully your update fixes it As for my TBS6902 Signal strength of my 6902 at my Location on another TP is about 1db less SNR to the location of the TBS6983 in EbsPro but still good...
-
See official GX1133 features. Current driver code refuse SR < 800 Ks and >65000 Ks. I change low limit to 100Ks, try latest test build
-
However on a TBS6983 of my mate in WA gets the TP's detected on crazyscan. STV0910 based devices best for ultra low SR reception. TBS 6983, 6903, 6905, 6908, 5927.
-
See official GX1133 features. Current driver code refuse SR < 800 Ks and >65000 Ks. I change low limit to SR 100Ks, try latest test build
-
See official GX1133 features. Current driver code refuce SR < 800 Ks and >65000 Ks. I change low limit to SR 100Ks, try latest test build
-
-
VLT in AltDVB is not limited to 10s. 10s is timeout if VLT is disabled. If VLT is enabled - timeout is longer when SR is lower - you can measure that. If timeout is set to just 1000ms and VLT is enabled - really timeout is happening at my setup after 8s. If timeout is set to 10000ms and VLT is enabled - really timeout is happening after 50s, not 10s as selected. VLT multiplies selected timeout. Only when VLT is disabled, then timeout will be exactly as selected. In the best case AltDVB can wait even...
-
VLT in AltDVB is not limited to 10s. 10s is timeout if VLT is disabled. If VLT is enabled - timeout is longer when SR is lower - you can measure that. If timeout is set to just 1000ms and VLT is enabled - really timeout is happening at my setup after 8s. If timeout is set to 10000ms and VLT is enabled - really timeout is happening after 50s, not 10s as selected. VLT multiplies selected timeout. Only when VLT is disabled, then timeout will be exactly as selected. In the best case AltDVB can wait even...
-
thanks for the confirmation
-
Using my Vu+Duo2 receiver 4196H SR 1415 locks but takes 8 to 15 seconds to show a signal bar and locks reliably to give video/sound. ALTDVB is limited to 10 Sec Max by setting VLT but still not enough. Tested all 3 Muxes concerned. Incidentally although in Crazyscan the RF scan can be set to 100KHz step. I think Blind Scan is still 1MHz as in Analyzer you can't set below 1MHz, Also in Analyzer the SR drop down menu goes no lower than 1000 but can enter 520 manually. No idea if the lower manual entry...
-
Using my Vu+Duo2 receiver 4196H SR 1415 locks but takes 8 to 15 seconds to show a signal bar and locks reliably to give video/sound. ALTDVB is limited to 10 Sec Max by setting VLT but still not enough. Tested all 3 Muxes concerned. Incidentally although in Crazyscan the RF scan can be set to 100KHz step. I think Blind Scan is still 1MHz as in Analyzer you can't set below 1MHz, Also in Analyzer the SR drop down menu goes no lower than 1000 but can enter 100 manually. No idea if the lower manual entry...
-
Most of TBS devices are working badly with low SR except of their professional devices like 5927, 6983, 6925 etc. Blindscan of SR >1500 ksps will often fail on non-pro devices. Used tuners & demods lacking the precision and if more signals close to each other, then situation only getting worse. Making smaller steps won't help here - this HW just won't jump over this. With CrazyScan you can already set steps to 0,1 MHz if HW is capable to do so. And I assure you, that this won't change anything -...
-
No, it does not, TBS5930-lite does not work with S2X. Official site mistakenly copied description from TBS5930 (non-lite version), but on their shop description is correct.
-
OK, Well DVBDream in BDA mode will not tune 4196H . However my Vu+Duo2 Rx can and able to view channel. This could be telling me there is a bug in the TBS 6902 or its confused having 2 other TP's 1MHz either side of 4196H. A test in WA with Streamreader using a TBS 6983 (a well known does all card of earlier times) can see 2 of the 3 Transponders in crazyscan but hit n miss as 2/3 TP's have an sr < 1000. Why the satellite does this I've no idea but makes it hard to separate them. *** Can a smaller...
-
@crazycat69 can you confirm if TBS5930lite support dvb-s2x? the official site says yes but I doubt. Thanks!
-
Ordered the TBS5930lite from China to Italy card + shipping + VAT = €98 soon it should arrive, if I need it can I contact you? Thanks CrazyCat
1 >