Have you tried enabling DMA transfers on parport_pc using a dma argument? I assume you don't have a printer plugged into the scanner either? There seems to be no response at all in that output :(
- Matthew
If you would like to refer to this comment somewhere else in this project, copy and paste the following link:
yes i try passing those parameters in modules.conf, but now i reinstall everthing with rpms, backend, frontend, libieee1284 and compile scan driver but says me:
Finding IEEE1284 ports...
parport0 (0x378): <raw><cpt><nbl><byt><swe><irq>... OK (ecp-swe).
Detecting scanner:
Timeout: Scanner wakeup reply 1 (0x03 in 0x1f) - Status = 0x1f
Timeout: Scanner wakeup reply 2 (0x03 in 0x1f) - Status = 0x1f
Timeout: Scanner wakeup reply 1 (0x03 in 0x1f) - Status = 0x1f
Timeout: Scanner wakeup reply 2 (0x03 in 0x1f) - Status = 0x1f
Timeout: Scanner wakeup reply 1 (0x03 in 0x1f) - Status = 0x1f
Timeout: Reply 2 (0x0c in 0x1f) - Status = 0x1f
initialise: could not wake scanner
Fatal: Unable to initialise scanner! (Code 1)
when i scan -C
any idea................. please!!!!!!!!!!!!
best regards!
Arturo
If you would like to refer to this comment somewhere else in this project, copy and paste the following link:
hello,
i've been follow all instructions for install on my fc4 and i doesn't work... when i exec libieee1284_test
Found 1 ports:
parport0:
parport0: 0x378 (ECR at 0x778)
RAW NIBBLE BYTE COMPAT ECPSWE EPP IR
but xsane show me:
[canon_pp] sane_init: ><
[canon_pp] sane_init: >#init_mode AUTO<
[canon_pp] sane_init: ># init_mode FB620P parport0<
[canon_pp] sane_init: >init_mode FB630P parport0<
[canon_pp] sane_init: Parsed init.
[canon_pp] detect_mode: Opening port parport0
[canon_pp] detect_mode: Claiming port.
[canon_pp] detect_mode: Port supports ECP-S.
[canon_pp] detect_mode: Port supports interrupts.
[canon_pp] detect_mode: Using ECP-S Mode
[canon_pp] sane_init: >> initialise
[canon_pp] Timeout: Scanner wakeup reply 1 (0x03 in 0x1f) - Status = 0x1f
[canon_pp] Timeout: Scanner wakeup reply 2 (0x03 in 0x1f) - Status = 0x1f
[canon_pp] Timeout: Scanner wakeup reply 1 (0x03 in 0x1f) - Status = 0x1f
[canon_pp] Timeout: Scanner wakeup reply 2 (0x03 in 0x1f) - Status = 0x1f
[canon_pp] Timeout: Scanner wakeup reply 1 (0x03 in 0x1f) - Status = 0x1f
[canon_pp] Timeout: Reply 2 (0x0c in 0x1f) - Status = 0x1f
[canon_pp] initialise: could not wake scanner
[canon_pp] sane_init: << 1 initialise
[canon_pp] sane_init: Couldn't contact scanner on port parport0. Probably no scanner there?
[canon_pp] << sane_init
[canon_pp] >> sane_get_devices (0xbfc49378, 0)
[canon_pp] << sane_get_devices
what's wrong??? any idea? help please?...
thanks,
Catador.
G'day,
Have you tried enabling DMA transfers on parport_pc using a dma argument? I assume you don't have a printer plugged into the scanner either? There seems to be no response at all in that output :(
- Matthew
hi!
yes i try passing those parameters in modules.conf, but now i reinstall everthing with rpms, backend, frontend, libieee1284 and compile scan driver but says me:
Finding IEEE1284 ports...
parport0 (0x378): <raw><cpt><nbl><byt><swe><irq>... OK (ecp-swe).
Detecting scanner:
Timeout: Scanner wakeup reply 1 (0x03 in 0x1f) - Status = 0x1f
Timeout: Scanner wakeup reply 2 (0x03 in 0x1f) - Status = 0x1f
Timeout: Scanner wakeup reply 1 (0x03 in 0x1f) - Status = 0x1f
Timeout: Scanner wakeup reply 2 (0x03 in 0x1f) - Status = 0x1f
Timeout: Scanner wakeup reply 1 (0x03 in 0x1f) - Status = 0x1f
Timeout: Reply 2 (0x0c in 0x1f) - Status = 0x1f
initialise: could not wake scanner
Fatal: Unable to initialise scanner! (Code 1)
when i scan -C
any idea................. please!!!!!!!!!!!!
best regards!
Arturo
hi!
i forget!!! i don't use parallel priinter just scanner!!
:D