#30 No sound, CSR-based or not?

[Anonymous]

So I can load the btsco module but I cant output sound over the
alsa-driver. The headset just makes a connection beep when I press
play in xmms.

According to the "Discussion" chapter my adapter is not csr-based:
tulkar@tyr01:~$ sudo hciconfig hci0 revision
hci0: Type: USB
BD Address: 00:0E:A1:33:AD:6C ACL MTU: 377:10 SCO MTU:
16:0
Firmware 0.3 / 9

But according to Holtmanns adapter list it is!
MSI MS-6970 USB 0xff 0xff 0x0f 0x00 1.1 (0x020d) 1.1 (0x020d)
CSR <--- !!!

So is it or isn't it CSR-based? Also, if it is, is there no way atm to get
headset functionality working with this chipset.

Thanks a lot for any help!

Here some output:

tulkar@tyr01:~$ sudo hciconfig -a
hci0: Type: USB
BD Address: 00:0E:A1:33:AD:6C ACL MTU: 377:10 SCO MTU:
16:0
UP RUNNING PSCAN ISCAN
RX bytes:69139 acl:252 sco:0 events:6985 errors:0
TX bytes:37454 acl:212 sco:0 commands:6547 errors:0
Features: 0xff 0xfe 0x0d 0x38 0x08 0x08 0x00 0x00
Packet type: DM1 DM3 DM5 DH1 DH3 DH5 HV1 HV2 HV3
Link policy: RSWITCH HOLD SNIFF PARK
Link mode: SLAVE ACCEPT
Name: 'tyr01-0'
Class: 0x3e0100
Service Classes: Networking, Rendering, Capturing
Device Class: Computer, Uncategorized
HCI Ver: 1.2 (0x2) HCI Rev: 0x0 LMP Ver: 1.2 (0x2) LMP Subver:
0x309
Manufacturer: Broadcom Corporation (15)

tulkar@tyr01:~$ sudo hcitool info 00:0D:44:36:F9:FB
Requesting information ...
BD Address: 00:0D:44:36:F9:FB
Device Name: Logitech HS02-V07
LMP Version: 1.2 (0x2) LMP Subversion: 0x611
Manufacturer: Cambridge Silicon Radio (10)
Features: 0xfc 0xfe 0x0f 0x00 0x08 0x08 0x00 0x00
<encryption> <slot offset> <timing accuracy> <role
switch>
<hold mode> <sniff mode> <RSSI> <channel quality>
<SCO link>
<HV2 packets> <HV3 packets> <u-law log> <A-law log>
<CVSD>
<paging scheme> <power control> <transparent SCO>
<AFH cap. slave> <AFH cap. master>

tulkar@tyr01:~$ sudo btsco -v 00:0D:44:36:F9:FB
btsco v0.4c
Device is 1:0
Voice setting: 0x0060
RFCOMM channel 1 connected
speaker volume: 12 mic volume: 1
speaker volume: 12 mic volume: 1
i/o needed: connecting sco...
connected SCO channel
Done setting sco fd
recieved AT+VGS=12
Sending up speaker change 12
speaker volume: 12 mic volume: 1
driver is not in use
disconnected SCO channel
speaker volume: 12 mic volume: 1
i/o needed: connecting sco...
Can't connect SCO audio channel
: Software caused connection abort
speaker volume: 12 mic volume: 1
speaker volume: 12 mic volume: 1
i/o needed: connecting sco...
connected SCO channel
Done setting sco fd
recieved AT+VGS=12
Sending up speaker change 12
speaker volume: 12 mic volume: 1
driver is not in use
disconnected SCO channel
speaker volume: 12 mic volume: 1
i/o needed: connecting sco...
Can't connect SCO audio channel
: Software caused connection abort
speaker volume: 12 mic volume: 1
speaker volume: 12 mic volume: 1
i/o needed: connecting sco...
connected SCO channel
Done setting sco fd
recieved AT+VGS=12
Sending up speaker change 12
recieved AT+VGS=06
Sending up speaker change 6
recieved AT+VGS=07
Sending up speaker change 7
recieved AT+VGS=08
Sending up speaker change 8
speaker volume: 8 mic volume: 1
driver is not in use

[Nobody/Anonymous]

Logged In: NO

I have a similar problem and have the same output from "hciconfig hci0 revision".
I have it working using the headsetd plugin - only the btsco (needed for skype!) does not work.

Did you have any success in having your setup work?

[sam]

Logged In: YES
user_id=1171269
Originator: NO

I gave up on this issue due to lack of time, sorry not to be able to help you any further