Hello Everybody,
I am using Telecom 0.3.8 on Speedport W500v. Unfortunately I haven't been able to use VoIP so far, I have been configuring VoIP ATAs and routers and know that I am not missing anything in configuration but still I am unable to connect with VoIP service.
Please see snapshots of my configurations below. One thing that voice interface I used to set in my other routers to ppp_8_81_1 which I did using telnet in those routers like BT Voyager 2500.
Does voice interface has anything to do with it ? Please see snapshots links below:
You are not missing anything in configuration but some values are simply not correct. The following settings did let me register with Voxalot right away:
hello,
thank you for replying and your help. I tried but it didn't help. I even tried Australian server (which is set in my Voxalot account ) but no luck. I have tried to configure my Sipsorcery account as well but again no luck.
Do you know how to change voice interface to ppp_8_81_1 ? As Bitswitcher firmware for Speedport W 500v says that voice set interface is set to ppp_1_32_1
Fritzbox still in the same state, will try again on some weekdays, hope Gurus on ip-phone forum will help, they are great guys.
Regards,
Jim.
If you would like to refer to this comment somewhere else in this project, copy and paste the following link:
Are you saying you have to use a secondary ATM connection vor voice?
It can be enabled in the mask "Network Settings: DSL/WAN" and its specific VPI and VCI values will also be set there.
Greetings,
KunterBunter
If you would like to refer to this comment somewhere else in this project, copy and paste the following link:
No I don't want to enable secondary ATM connection. Default voice interface in BS is ppp_1_32_1 which I feel if changed to ppp_8_81_1 will allow VoIP connection.
Do you see "Not connected" in VoIP page of BS even after connected ?
If you would like to refer to this comment somewhere else in this project, copy and paste the following link:
As I said, with the correct values from above, VoIP connection is registered and, of course, I see " connection established" in Phone settings.
VPI and VCI values for the Primary ATM connection can also be changed in the mask "Network Settings: DSL/WAN".
But I don't think it will help because it will not allow you to get a DSL connection with your provider.
If you would like to refer to this comment somewhere else in this project, copy and paste the following link:
Hello,
as far as I've noticed, I was unable to establish VoIP connection with Telekom firmware.
After flashing to TARGA firmware, connection was established right away.
The setting values are OK, tested on Speedport W701V with success.
So i think it something with Telekom firmware issue.
If you would like to refer to this comment somewhere else in this project, copy and paste the following link:
Hello Everybody,
I am using Telecom 0.3.8 on Speedport W500v. Unfortunately I haven't been able to use VoIP so far, I have been configuring VoIP ATAs and routers and know that I am not missing anything in configuration but still I am unable to connect with VoIP service.
Please see snapshots of my configurations below. One thing that voice interface I used to set in my other routers to ppp_8_81_1 which I did using telnet in those routers like BT Voyager 2500.
Does voice interface has anything to do with it ? Please see snapshots links below:
http://img560.imageshack.us/img560/1213/12702977.jpg
http://img574.imageshack.us/img574/5157/78724898.jpg
http://img824.imageshack.us/img824/3269/63490997.jpg
http://img529.imageshack.us/img529/8135/21565951.jpg
http://img576.imageshack.us/img576/3369/62851289.jpg
http://img607.imageshack.us/img607/6418/93801439.jpg
http://img585.imageshack.us/img585/3223/version.jpg
Please see that port 5060 is blocked by my ISP and voxalot supports port 2060 as well.
You are not missing anything in configuration but some values are simply not correct. The following settings did let me register with Voxalot right away:
* Subscriber: <6-digit Voxalot member-id>
* Username: <6-digit Voxalot member-id>
* Password: <Voxalot Password>
* Registrar Address: voxalot.com
* Registrar Port: 2060
* Proxy IP: au.voxalot.com
* Proxy Port: 2060
* Domain: voxalot.com
Only the 6-digit Voxalot member-id is required. You may use the IP address 202.60.88.238 instead of au.voxalot.com as the Proxy.
BTW, how is your fritzbox going, Jim?
hello,
thank you for replying and your help. I tried but it didn't help. I even tried Australian server (which is set in my Voxalot account ) but no luck. I have tried to configure my Sipsorcery account as well but again no luck.
Do you know how to change voice interface to ppp_8_81_1 ? As Bitswitcher firmware for Speedport W 500v says that voice set interface is set to ppp_1_32_1
Fritzbox still in the same state, will try again on some weekdays, hope Gurus on ip-phone forum will help, they are great guys.
Regards,
Jim.
Are you saying you have to use a secondary ATM connection vor voice?
It can be enabled in the mask "Network Settings: DSL/WAN" and its specific VPI and VCI values will also be set there.
Greetings,
KunterBunter
No I don't want to enable secondary ATM connection. Default voice interface in BS is ppp_1_32_1 which I feel if changed to ppp_8_81_1 will allow VoIP connection.
Do you see "Not connected" in VoIP page of BS even after connected ?
As I said, with the correct values from above, VoIP connection is registered and, of course, I see " connection established" in Phone settings.
VPI and VCI values for the Primary ATM connection can also be changed in the mask "Network Settings: DSL/WAN".
But I don't think it will help because it will not allow you to get a DSL connection with your provider.
Hello,
as far as I've noticed, I was unable to establish VoIP connection with Telekom firmware.
After flashing to TARGA firmware, connection was established right away.
The setting values are OK, tested on Speedport W701V with success.
So i think it something with Telekom firmware issue.