[Armadeus-commitlog] armadeus branch, master, updated. release-3.2-269-ge0d1b8c
Brought to you by:
sszy
Menu
▾
▴
[Armadeus-commitlog] armadeus branch, master, updated. release-3.2-269-ge0d1b8c
|
From: jorasse <jo...@us...> - 2010-03-30 22:42:07
|
This is an automated email from the git hooks/post-receive script. It was
generated because a ref change was pushed to the repository containing
the project "armadeus".
The branch, master has been updated
via e0d1b8ccec96b040c9cf758aa6a3fc8236d84336 (commit)
from 53cdca87ed4f7117dadf0cd6065d60e853f46a43 (commit)
Those revisions listed above that are new to this repository have
not appeared on any other notification email; so we list those
revisions in full, below.
- Log -----------------------------------------------------------------
commit e0d1b8ccec96b040c9cf758aa6a3fc8236d84336
Author: jorasse <jo...@ar...>
Date: Wed Mar 31 00:41:10 2010 +0200
[U-Boot] added U-Boot 2010.03-rc2 support for apf9328
-----------------------------------------------------------------------
Summary of changes:
.../apf27/{apf27.h => apf27-u-boot-1.3.4.h} | 0
.../target/device/armadeus/apf27/apf27_defconfig | 2 +-
.../apf9328/{apf9328.h => apf9328-u-boot-1.3.4.h} | 0
.../armadeus/apf9328/apf9328-u-boot-2010.03-rc2.h | 1018 ++++++++++++++++++++
.../device/armadeus/apf9328/apf9328_defconfig | 14 +-
...-imx.patch => u-boot-2010.03-rc2-100-imx.patch} | 36 +-
....patch => u-boot-2010.03-rc2-110-apf9328.patch} | 268 +++---
.../u-boot-2010.03-rc2-111-apf9328-DM9000.patch | 133 +++
.../u-boot-2010.03-rc2-112-apf9328-makefile.patch | 22 +
... => u-boot-2010.03-rc2-120-apf9328-tools.patch} | 135 ++--
...4.patch => u-boot-2010.03-rc2-140-ds1374.patch} | 24 +-
...pf9328-fixes_gcc_4_4_EABI_linking_issues.patch} | 38 +-
.../051i-u-boot-multi-version-support.patch | 40 +
13 files changed, 1469 insertions(+), 261 deletions(-)
copy buildroot/target/device/armadeus/apf27/{apf27.h => apf27-u-boot-1.3.4.h} (100%)
copy buildroot/target/device/armadeus/apf9328/{apf9328.h => apf9328-u-boot-1.3.4.h} (100%)
create mode 100644 buildroot/target/device/armadeus/apf9328/apf9328-u-boot-2010.03-rc2.h
copy buildroot/target/u-boot/{u-boot-1.3.4-100-imx.patch => u-boot-2010.03-rc2-100-imx.patch} (74%)
copy buildroot/target/u-boot/{u-boot-1.3.4-110-apf9328.patch => u-boot-2010.03-rc2-110-apf9328.patch} (83%)
create mode 100644 buildroot/target/u-boot/u-boot-2010.03-rc2-111-apf9328-DM9000.patch
create mode 100644 buildroot/target/u-boot/u-boot-2010.03-rc2-112-apf9328-makefile.patch
copy buildroot/target/u-boot/{u-boot-1.3.4-120-apf9328-tools.patch => u-boot-2010.03-rc2-120-apf9328-tools.patch} (73%)
copy buildroot/target/u-boot/{u-boot-1.3.4-140-ds1374.patch => u-boot-2010.03-rc2-140-ds1374.patch} (73%)
copy buildroot/target/u-boot/{u-boot-1.3.4-402-apf9328-fixes_gcc_4_4_EABI_linking_issues.patch => u-boot-2010.03-rc2-150-apf9328-fixes_gcc_4_4_EABI_linking_issues.patch} (71%)
create mode 100644 patches/buildroot/2010.02/051i-u-boot-multi-version-support.patch
diff --git a/buildroot/target/device/armadeus/apf27/apf27.h b/buildroot/target/device/armadeus/apf27/apf27-u-boot-1.3.4.h
similarity index 100%
copy from buildroot/target/device/armadeus/apf27/apf27.h
copy to buildroot/target/device/armadeus/apf27/apf27-u-boot-1.3.4.h
diff --git a/buildroot/target/device/armadeus/apf27/apf27_defconfig b/buildroot/target/device/armadeus/apf27/apf27_defconfig
index 02805ee..bbc6a84 100644
--- a/buildroot/target/device/armadeus/apf27/apf27_defconfig
+++ b/buildroot/target/device/armadeus/apf27/apf27_defconfig
@@ -772,7 +772,7 @@ BR2_TARGET_ROOTFS_TAR_COPYTO=""
#
BR2_TARGET_UBOOT=y
BR2_TARGET_UBOOT_BOARDNAME="$(BR2_BOARD_NAME)"
-BR2_TARGET_U_BOOT_CONFIG_HEADER_FILE="$(BR2_BOARD_PATH)/$(BR2_BOARD_NAME).h"
+BR2_TARGET_U_BOOT_CONFIG_HEADER_FILE="$(BR2_BOARD_PATH)/$(BR2_BOARD_NAME)-uboot-$(BR2_UBOOT_VERSION).h"
BR2_TARGET_UBOOT_CUSTOM_PATCH=""
BR2_TARGET_UBOOT_SERVERIP=""
BR2_TARGET_UBOOT_IPADDR=""
diff --git a/buildroot/target/device/armadeus/apf9328/apf9328.h b/buildroot/target/device/armadeus/apf9328/apf9328-u-boot-1.3.4.h
similarity index 100%
copy from buildroot/target/device/armadeus/apf9328/apf9328.h
copy to buildroot/target/device/armadeus/apf9328/apf9328-u-boot-1.3.4.h
diff --git a/buildroot/target/device/armadeus/apf9328/apf9328-u-boot-2010.03-rc2.h b/buildroot/target/device/armadeus/apf9328/apf9328-u-boot-2010.03-rc2.h
new file mode 100644
index 0000000..af8cb69
--- /dev/null
+++ b/buildroot/target/device/armadeus/apf9328/apf9328-u-boot-2010.03-rc2.h
@@ -0,0 +1,1018 @@
+/*
+ * Eric Jarrige <jo...@us...>
+ *
+ * Configuration settings for the Armadeus Project motherboard 9328 board.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ * 2005/01/14 Initial version taken from the scb9328 configuration file
+ * 2005/03/10 apf9328 configuration file and trial to improve of
+ * hardware register control.
+ * 2005/08/16 added APF9328 fpgas and ethernet
+ * 2005/12/02 added filesystem boot over NFS
+ * 2006/11/26 added filesystem boot over NFS
+ * 2010/03/28 U-Boot 2010.03 migration + change timer unit to ms (fixme)
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#define CONFIG_VERSION_VARIABLE
+#define CONFIG_ENV_VERSION "3.7"
+#define CONFIG_IDENT_STRING " apf9328 patch 4.0"
+
+#define CONFIG_ARM920T 1 /* this is an ARM920T CPU */
+#define CONFIG_IMX 1 /* in a Motorola MC9328MXL Chip */
+#define CONFIG_apf9328 1 /* on a Armadeus project board */
+#undef CONFIG_USE_IRQ /* don't need use IRQ/FIQ */
+
+/*
+ * Enable the call to misc_init_r() for miscellaneous platform
+ * dependent initialization.
+ */
+
+#define CONFIG_MISC_INIT_R
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+#define CONFIG_BOOTP_SUBNETMASK
+#define CONFIG_BOOTP_DNS
+#define CONFIG_BOOTP_DNS2
+
+/*
+ * Select serial console configuration
+ */
+#define CONFIG_IMX_SERIAL
+#define CONFIG_IMX_SERIAL1
+#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 }
+#define CONFIG_BAUDRATE 115200
+
+/*
+ * Definition of u-boot build in commands. Check out CONFIG_CMD_DFL if
+ * neccessary in include/cmd_confdefs.h file. (Un)comment for getting
+ * functionality or size of u-boot code.
+ */
+
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_ASKENV /* ask for env variable */
+#define CONFIG_CMD_BSP /* Board Specific functions */
+#define CONFIG_CMD_CACHE /* icache, dcache */
+#define CONFIG_CMD_CDP /* Cisco Discovery Protocol */
+#define CONFIG_CMD_DATE /* support for RTC, date/time...*/
+#define CONFIG_CMD_DHCP /* DHCP Support */
+#define CONFIG_CMD_DIAG /* Diagnostics */
+#define CONFIG_CMD_EEPROM /* EEPROM read/write support */
+//#define CONFIG_CMD_FAT /* FAT support */
+#define CONFIG_CMD_FLASH /* flinfo, erase, protect */
+#define CONFIG_CMD_I2C /* I2C serial bus support */
+#define CONFIG_CMD_IMLS /* List all found images */
+#define CONFIG_CMD_IMMAP /* IMMR dump support */
+#define CONFIG_CMD_JFFS2 /* JFFS2 Support */
+//#define CONFIG_CMD_MII /* MII support */
+#define CONFIG_CMD_MTDPARTS /* MTD partition support */
+#define CONFIG_CMD_PING /* ping support */
+#define CONFIG_CMD_SAVES /* save S record dump */
+#define CONFIG_CMD_SETEXPR /* setexpr support */
+#define CONFIG_CMD_SNTP /* SNTP support */
+#define CONFIG_CMD_NFS
+#define CONFIG_CMD_DNS
+
+#undef CONFIG_DISPLAY_BOARDINFO
+#undef CONFIG_DISPLAY_CPUINFO
+
+/*
+ * Select some advanced features of the commande line parser
+ */
+#define CONFIG_AUTO_COMPLETE 1 /* Enable auto completion of */
+ /* commands using TAB */
+#define CONFIG_SYS_HUSH_PARSER 1 /* enable the "hush" shell */
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " /* secondary prompt string */
+#define CONFIG_CMDLINE_EDITING 1
+
+#define CONFIG_MTD_DEVICE
+#define CONFIG_MTD_PARTITIONS
+/*
+ * Boot options. Setting delay to -1 stops autostart count down.
+ */
+#define CONFIG_BOOTDELAY 20
+#define CONFIG_ZERO_BOOTDELAY_CHECK
+
+#define CONFIG_BOOTARGS \
+ CONFIG_CONSOLE " root=/dev/mtdblock4 rootfstype=jffs2 " MTDPARTS_DEFAULT
+
+#define CONFIG_CONSOLE "console=ttySMX0,"MK_STR(CONFIG_BAUDRATE)"n8"
+#define CONFIG_MTDMAP "physmap-flash.0"
+#define MTDIDS_DEFAULT "nor0=" CONFIG_MTDMAP
+#define MTDPARTS_DEFAULT "mtdparts=" CONFIG_MTDMAP ":256k(U-boot)ro," \
+ "128k(U-boot_env),256k(firmware),2048k(kernel),-(rootfs)"
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "env_version=" CONFIG_ENV_VERSION "\0" \
+ "fileaddr=" MK_STR(CONFIG_SYS_LOAD_ADDR) "\0" \
+ "filesize=" MK_STR(CONFIG_SYS_MONITOR_LEN) "\0" \
+ "console=" CONFIG_CONSOLE "\0" \
+ "mtdparts=" MTDPARTS_DEFAULT "\0" \
+ "partition=nor0,4\0" \
+ "uboot_addr=" MK_STR(CONFIG_SYS_MONITOR_BASE) "\0" \
+ "uboot_len=" MK_STR(CONFIG_SYS_MONITOR_LEN) "\0" \
+ "env_addr=" MK_STR(CONFIG_ENV_ADDR) "\0" \
+ "env_len=" MK_STR(CONFIG_ENV_SIZE) "\0" \
+ "firmware_addr=" MK_STR(CONFIG_FIRMWARE_ADDR) "\0" \
+ "firmware_len=" MK_STR(CONFIG_FIRMWARE_LEN) "\0" \
+ "kernel_addr=" MK_STR(CONFIG_KERNEL_ADDR) "\0" \
+ "kernel_len=" MK_STR(CONFIG_KERNEL_LEN) "\0" \
+ "rootfs_addr=" MK_STR(CONFIG_ROOTFS_ADDR) "\0" \
+ "rootfs_len=" MK_STR(CONFIG_ROOTFS_LEN) "\0" \
+ "board_name=" MK_STR(CONFIG_BOARD_NAME) "\0" \
+ "serverpath=" MK_STR(CONFIG_SRV_PATH) "\0" \
+ "ntpserverip=217.147.208.1\0" \
+ "mmcroot=/dev/mmcblk0p1\0" \
+ "mmcrootfstype=ext2\0" \
+ "addnfsargs=setenv bootargs ${bootargs} " \
+ "root=/dev/nfs rw nfsroot=${serverip}:${rootpath}\0" \
+ "addjffsargs=setenv bootargs ${bootargs} " \
+ "root=/dev/mtdblock4 rootfstype=jffs2\0" \
+ "addubifsargs=setenv bootargs ${bootargs} " \
+ "ubi.mtd=rootfs root=ubi0:rootfs rootfstype=ubifs\0" \
+ "addmmcargs=setenv bootargs ${bootargs} " \
+ "root=${mmcroot} rootfstype=${mmcrootfstype}\0" \
+ "addipargs=setenv bootargs ${bootargs} " \
+ "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off \0"\
+ "nfsboot=setenv bootargs ${console} ${mtdparts};" \
+ "run addnfsargs addipargs; bootm ${kernel_addr}\0" \
+ "jffsboot=setenv bootargs ${console} ${mtdparts};" \
+ "run addjffsargs addipargs; bootm ${kernel_addr}\0" \
+ "ubifsboot=setenv bootargs ${console} ${mtdparts};" \
+ "run addubifsargs addipargs; bootm ${kernel_addr}\0" \
+ "mmcboot=setenv bootargs ${console} ${mtdparts};" \
+ "run addmmcargs addipargs; bootm ${kernel_addr}\0" \
+ "firmware_autoload=0\0" \
+ "flash_uboot=protect off ${uboot_addr} +${uboot_len};" \
+ "echo Erasing FLASH;" \
+ "era ${uboot_addr} +${uboot_len};" \
+ "if cp.b ${fileaddr} ${uboot_addr} ${filesize};" \
+ "then protect on ${uboot_addr} +${uboot_len};" \
+ "echo Flashing of uboot succeed;" \
+ "else echo Flashing of uboot failed;" \
+ "fi; \0" \
+ "flash_firmware=echo Erasing FLASH;" \
+ "era ${firmware_addr} +${firmware_len};" \
+ "if cp.b ${fileaddr} ${firmware_addr} ${filesize} ;" \
+ "then echo Flashing of Firmware succeed;" \
+ "else echo Flashing of Firmware failed;" \
+ "fi\0" \
+ "flash_kernel=echo Erasing FLASH;" \
+ "era ${kernel_addr} +${kernel_len};" \
+ "if cp.b ${fileaddr} ${kernel_addr} ${filesize} ;" \
+ "then echo Flashing of kernel succeed;" \
+ "else echo Flashing of kernel failed;" \
+ "fi\0" \
+ "flash_rootfs=echo Erasing FLASH;" \
+ "era ${rootfs_addr} +${rootfs_len};" \
+ "if cp.b ${fileaddr} ${rootfs_addr} ${filesize};" \
+ "then echo Flashing of rootfs succeed;" \
+ "else echo Flashing of rootfs failed;" \
+ "fi\0" \
+ "flash_reset_env=protect off ${env_addr} +${env_len};" \
+ "era ${env_addr} +${env_len};" \
+ "echo Erasing of flash environment variables done!\0" \
+ "download_uboot=tftpboot ${loadaddr} " \
+ " ${serverpath}${board_name}-u-boot.bin\0" \
+ "download_kernel=tftpboot ${loadaddr} " \
+ " ${serverpath}${board_name}-linux.bin\0" \
+ "download_rootfs=tftpboot ${loadaddr} " \
+ " ${serverpath}${board_name}-rootfs.arm.jffs2\0" \
+ "update_uboot=run download_uboot flash_uboot\0" \
+ "update_kernel=run download_kernel flash_kernel\0" \
+ "update_rootfs=run download_rootfs flash_rootfs\0" \
+ "update_all=run download_kernel flash_kernel download_rootfs " \
+ "flash_rootfs download_uboot flash_uboot\0" \
+ "unlock_regs=mw 00200008 0; mw 00210008 0\0" \
+
+#define CONFIG_BOOTCOMMAND "run jffsboot"
+#define CONFIG_SYS_AUTOLOAD "no"
+
+#define CONFIG_MACH_TYPE MACH_TYPE_APF9328
+#define CONFIG_BOOT_PARAMS_ADDR 0x08000100
+
+#undef CONFIG_SHOW_BOOT_PROGRESS
+
+#define CONFIG_ETHADDR
+#define CONFIG_NETMASK 255.255.255.0
+#define CONFIG_IPADDR 192.168.000.10
+#define CONFIG_BOARD_NAME "apf9328"
+#define CONFIG_HOSTNAME "apf9328"
+#define CONFIG_GATEWAYIP 192.168.000.1
+#define CONFIG_SERVERIP 192.168.000.2
+#define CONFIG_SRV_PATH ""
+#define CONFIG_ROOTPATH "/tftpboot/apf9328-root"
+
+/*
+ * General options for u-boot. Modify to save memory foot print
+ */
+
+#define CONFIG_SYS_LONGHELP
+#define CONFIG_SYS_PROMPT "BIOS> " /* prompt string */
+#define CONFIG_SYS_CBSIZE 256 /* console I/O buffer */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* print buffer size */
+#define CONFIG_SYS_MAXARGS 16 /* max command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* boot args buf size */
+
+#define CONFIG_SYS_MEMTEST_START 0x08000000 /* memtest test area */
+#define CONFIG_SYS_MEMTEST_END 0x08700000
+
+#define CONFIG_SYS_HZ 1000l /* incrementer freq: 1 MHz */
+
+/*
+ * Definitions related to passing arguments to kernel.
+ */
+
+#define CONFIG_CMDLINE_TAG 1 /* send commandline to Kernel */
+#define CONFIG_SETUP_MEMORY_TAGS 1 /* send memory definition to kernel */
+#define CONFIG_INITRD_TAG 1 /* send initrd params */
+#undef CONFIG_VFD /* do not send framebuffer setup */
+
+/*
+ * Malloc pool need to host env + 128 Kb reserve for other allocations.
+ */
+#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (128<<10) )
+
+#define CONFIG_SYS_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
+
+#define CONFIG_STACKSIZE (120<<10) /* stack size */
+
+#ifdef CONFIG_USE_IRQ
+#define CONFIG_STACKSIZE_IRQ (4<<10) /* IRQ stack */
+#define CONFIG_STACKSIZE_FIQ (4<<10) /* FIQ stack */
+#endif
+
+/*
+* Clocks configuration
+*/
+/*
+ * PLL configuration
+
+ f_{dpll}=2*f{ref}*(MFI+MFN/(MFD+1))/(PD+1)
+ f_ref=16,777216MHz
+ 32768 Hz xtal
+ 0x07B32DA5: 192.0000173
+ 0x002a141f: 191,9944MHz
+ 0x040b2007: 144MHz
+ 0x0FB32DA5: 96.00000864 MHz
+ 0x042a141f: 96MHz
+ 0x0811140d: 64MHz
+ 0x040e200e: 150MHz
+ 0x00321431: 200MHz
+
+ 16 MHz xtal
+ 0x08001800: 64MHz mit 16er Quarz
+ 0x04001800: 96MHz mit 16er Quarz
+ 0x04002400: 144MHz mit 16er Quarz
+
+ 31 |x x x x|x x x x|x x x x|x x x x|x x x x|x x x x|x x x x|x x x x| 0
+ |XXX|--PD---|-------MFD---------|XXX|--MFI--|-----MFN-----------|
+ */
+
+#define CONFIG_SYS_OSC32 32768 /* 32768 or 32000 Hz crystal */
+#undef CONFIG_SYS_OSC16 /* there is no external 16MHz external clock */
+
+/* MPU CLOCK source before PLL (should be named CONFIG_SYS_SYS_CLK_FREQ) */
+#define CONFIG_SYS_CLK_FREQ (512*CONFIG_SYS_OSC32)
+#define CONFIG_SYS_MPCTL0_VAL 0x07B32DA5 /* 192.000017 MHz */
+#define CONFIG_SYS_MPCTL1_VAL 0
+
+/* system clock source before PLL (should be named CONFIG_SYS_SYSPLL_CLK_FREQ) */
+#ifndef CONFIG_SYS_OSC16
+#define CONFIG_SYSPLL_CLK_FREQ (512*CONFIG_SYS_OSC32)
+#if (CONFIG_SYS_OSC32 == 32000)
+#define CONFIG_SYS_SPCTL0_VAL 0x043F1437 /* 96 MHz */
+#define CONFIG_SYS_SPCTL1_VAL 0
+#define CONFIG_SYS_FREQ 96 /* MHz */
+#else /* CONFIG_SYS_OSC32 == 32768*/
+#define CONFIG_SYS_SPCTL0_VAL 0x0FB32DA5 /* 96.000009 MHz */
+#define CONFIG_SYS_SPCTL1_VAL 0
+#define CONFIG_SYS_FREQ 96 /* MHz */
+#endif /* CONFIG_SYS_OSC32 */
+#else /* CONFIG_SYS_OSC16 in use*/
+#define CONFIG_SYSPLL_CLK_FREQ CONFIG_SYS_OSC16
+#define CONFIG_SYS_SPCTL0_VAL 0x04001401 /* 96 MHz */
+#define CONFIG_SYS_SPCTL1_VAL 0x0C000040
+#define CONFIG_SYS_FREQ 96 /* MHz */
+#endif /* CONFIG_SYS_OSC16 */
+
+/* external bus frequency (have to be a CONFIG_SYS_FREQ ratio) */
+#define CONFIG_SYS_BUS_FREQ 96 /* 96|48... MHz (BCLOCK and HCLOCK) */
+#define CONFIG_USB_FREQ 48 /* 48 MHz */
+#define CONFIG_PERIF1_FREQ 16 /* 16 MHz UART, Timer PWM*/
+#define CONFIG_PERIF2_FREQ 48 /* 48 MHz LCD SD SPI*/
+#define CONFIG_PERIF3_FREQ 16 /* 16 MHz SSI*/
+
+
+/*
+ * SDRAM definition parameter
+ */
+#define CONFIG_NR_DRAM_BANKS 1 /* we have and support only 1 bank of SDRAM */
+
+#define CONFIG_SYS_SDRAM_MBYTE_SYZE 16
+
+#if (CONFIG_SYS_SDRAM_MBYTE_SYZE == 8)
+/* micron 8MB */
+#define CONFIG_SYS_SDRAM_1_BASE 0x08000000 /* SDRAM bank #1 32bits */
+#define CONFIG_SYS_SDRAM_1_SIZE 0x00800000 /* 8 MB */
+#define CONFIG_SYS_SDRAM_NUM_COL 8 /* 8, 9, 10 or 11 column address bits */
+#define CONFIG_SYS_SDRAM_NUM_ROW 11 /* 11, 12 or 13 row address bits */
+#define CONFIG_SYS_SDRAM_REFRESH 2 /* 0=OFF 1=2048 2=4096 3=8192 refresh */
+#define CONFIG_SYS_SDRAM_CLOCK_CYCLE_CL_1 20 /* ns clock cycle time when CL=1 */
+#define CONFIG_SYS_SDRAM_ROW_PRECHARGE_DELAY 20 /* ns SRP */
+#define CONFIG_SYS_SDRAM_ROW_2_COL_DELAY 20 /* ns SRCD */
+#define CONFIG_SYS_SDRAM_ROW_CYCLE_DELAY 70 /* ns SRC */
+#define CONFIG_SYS_SDRAM_BURST_LENGTH 3 /* 2^N BYTES (N=0..3) */
+#define CONFIG_SYS_SDRAM_SINGLE_ACCESS 0 /* 1= single access; 0 = Burst mode */
+#endif
+
+#if (CONFIG_SYS_SDRAM_MBYTE_SYZE == 16)
+/* micron 16MB */
+#define CONFIG_SYS_SDRAM_1_BASE 0x08000000 /* SDRAM bank #1 32bits */
+#define CONFIG_SYS_SDRAM_1_SIZE 0x01000000 /* 16 MB */
+#define CONFIG_SYS_SDRAM_NUM_COL 8 /* 8, 9, 10 or 11 column address bits */
+#define CONFIG_SYS_SDRAM_NUM_ROW 12 /* 11, 12 or 13 row address bits */
+#define CONFIG_SYS_SDRAM_REFRESH 2 /* 0=OFF 1=2048 2=4096 3=8192 refresh */
+#define CONFIG_SYS_SDRAM_CLOCK_CYCLE_CL_1 20 /* ns clock cycle time when CL=1 */
+#define CONFIG_SYS_SDRAM_ROW_PRECHARGE_DELAY 20 /* ns SRP */
+#define CONFIG_SYS_SDRAM_ROW_2_COL_DELAY 20 /* ns SRCD */
+#define CONFIG_SYS_SDRAM_ROW_CYCLE_DELAY 70 /* ns SRC */
+#define CONFIG_SYS_SDRAM_BURST_LENGTH 3 /* 2^N BYTES (N=0..3) */
+#define CONFIG_SYS_SDRAM_SINGLE_ACCESS 0 /* 1= single access; 0 = Burst mode */
+#endif
+
+#if (CONFIG_SYS_SDRAM_MBYTE_SYZE == 32)
+/* micron 32MB */
+#define CONFIG_SYS_SDRAM_1_BASE 0x08000000 /* SDRAM bank #1 32bits */
+#define CONFIG_SYS_SDRAM_1_SIZE 0x02000000 /* 32 MB */
+#define CONFIG_SYS_SDRAM_NUM_COL 9 /* 8, 9, 10 or 11 column address bits */
+#define CONFIG_SYS_SDRAM_NUM_ROW 12 /* 11, 12 or 13 row address bits */
+#define CONFIG_SYS_SDRAM_REFRESH 2 /* 0=OFF 1=2048 2=4096 3=8192 refresh */
+#define CONFIG_SYS_SDRAM_CLOCK_CYCLE_CL_1 20 /* ns clock cycle time when CL=1 */
+#define CONFIG_SYS_SDRAM_ROW_PRECHARGE_DELAY 20 /* ns SRP */
+#define CONFIG_SYS_SDRAM_ROW_2_COL_DELAY 20 /* ns SRCD */
+#define CONFIG_SYS_SDRAM_ROW_CYCLE_DELAY 70 /* ns SRC */
+#define CONFIG_SYS_SDRAM_BURST_LENGTH 3 /* 2^N BYTES (N=0..3) */
+#define CONFIG_SYS_SDRAM_SINGLE_ACCESS 0 /* 1= single access; 0 = Burst mode */
+#endif
+
+#if (CONFIG_SYS_SDRAM_MBYTE_SYZE == 64)
+/* micron 64MB */
+#define CONFIG_SYS_SDRAM_1_BASE 0x08000000 /* SDRAM bank #1 32bits */
+#define CONFIG_SYS_SDRAM_1_SIZE 0x04000000 /* 64 MB */
+#define CONFIG_SYS_SDRAM_NUM_COL 9 /* 8, 9, 10 or 11 column address bits */
+#define CONFIG_SYS_SDRAM_NUM_ROW 13 /* 11, 12 or 13 row address bits */
+#define CONFIG_SYS_SDRAM_REFRESH 3 /* 0=OFF 1=2048 2=4096 3=8192 refresh */
+#define CONFIG_SYS_SDRAM_CLOCK_CYCLE_CL_1 20 /* ns clock cycle time when CL=1 */
+#define CONFIG_SYS_SDRAM_ROW_PRECHARGE_DELAY 20 /* ns SRP */
+#define CONFIG_SYS_SDRAM_ROW_2_COL_DELAY 20 /* ns SRCD */
+#define CONFIG_SYS_SDRAM_ROW_CYCLE_DELAY 70 /* ns SRC */
+#define CONFIG_SYS_SDRAM_BURST_LENGTH 3 /* 2^N BYTES (N=0..3) */
+#define CONFIG_SYS_SDRAM_SINGLE_ACCESS 0 /* 1= single access; 0 = Burst mode */
+#endif
+
+/*
+ * Configuration for a maximum 32MB of FLASH memory
+ */
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* FLASH banks count (not chip count) */
+#define CONFIG_SYS_MAX_FLASH_SECT 256 /* number of sector in FLASH bank */
+#define CONFIG_SYS_FLASH_BASE 0x10000000 /* location of flash memory */
+
+/* This should be defined if CFI FLASH device is present. */
+#define CONFIG_SYS_FLASH_CFI 1
+#define CONFIG_FLASH_CFI_DRIVER 1
+#define CONFIG_FLASH_CFI_MTD
+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */
+#define CONFIG_SYS_FLASH_PROTECTION 1
+#define CONFIG_SYS_DIRECT_FLASH_TFTP 1
+#define CONFIG_FLASH_SHOW_PROGRESS 45
+/*
+ * This is setting for JFFS2 support in u-boot.
+ * NOTE: Enable CONFIG_SYS_CMD_JFFS2 for JFFS2 support.
+ */
+#define CONFIG_SYS_JFFS_CUSTOM_PART
+
+/*
+ * Environment setup. Definitions of monitor location and size with
+ * definition of environment setup ends up in 2 possibilities.
+ * 1. Embeded environment - in u-boot code is space for environment
+ * 2. Environment is read from predefined sector of flash
+ * Right now we support 2. possiblity, but expecting no env placed
+ * on mentioned address right now. This also needs to provide whole
+ * sector for it - for us 256Kb is really waste of memory. U-boot uses
+ * default env. and until kernel parameters could be sent to kernel
+ * env. has no sense to us.
+ */
+
+#define CONFIG_SYS_MONITOR_BASE 0x10000000
+#define CONFIG_SYS_MONITOR_LEN 0x00040000 /* 256kB ( 2 flash sector ) */
+#define CONFIG_ENV_IS_IN_FLASH 1
+#define CONFIG_ENV_ADDR 0x10040000 /* absolute address for now */
+#define CONFIG_ENV_SIZE 0x00020000
+#define CONFIG_ENV_SECT_SIZE 0x00020000
+#define CONFIG_ENV_OVERWRITE 1 /* env is writable now */
+#define CONFIG_FIRMWARE_ADDR 0x10060000
+#define CONFIG_FIRMWARE_LEN 0x00040000 /* 256kB ( 2 flash sector ) */
+#define CONFIG_KERNEL_ADDR 0x100A0000
+#define CONFIG_KERNEL_LEN 0x00200000 /* 2MB */
+#define CONFIG_ROOTFS_ADDR 0x102A0000
+#define CONFIG_ROOTFS_LEN /* entire flash if not specified */
+
+/*
+ * Default load address for user programs and kernel
+ */
+#define CONFIG_SYS_LOAD_ADDR 0x08000000
+#define CONFIG_LOADADDR 0x08000000
+#define CONFIG_SYS_TFTP_LOADADDR 0x08000000
+/*
+ * Hardware drivers
+ */
+
+/* DM9000 ethernet chipset assigned to CS4 */
+/* For the apf board DM9000 base is 0x15C00000 and data is base+2 */
+/* For the apm board DM9000 base is 0x15C3FFFC and data is base+4 */
+#define CONFIG_DRIVER_DM9000 1
+//#undef CONFIG_DM9000_DEBUG
+#define CONFIG_DM9000_BASE 0x15C00000
+#define DM9000_IO CONFIG_DM9000_BASE
+#define DM9000_DATA (CONFIG_DM9000_BASE+2)
+#define CONFIG_NET_MULTI
+
+/*-----------------------------------------------------------------------
+ * FPGA stuff
+ */
+#define CONFIG_FPGA_COUNT 1
+/* only digital value for CONFIG_FPGA is supported (investigation pending) */
+#define CONFIG_FPGA 0x801 /* CONFIG_SYS_XILINX_SPARTAN3 */
+#define CONFIG_FPGA_XILINX
+#define CONFIG_FPGA_SPARTAN3
+#define CONFIG_SYS_FPGA_WAIT 250
+#define CONFIG_SYS_FPGA_PROG_FEEDBACK
+#define CONFIG_SYS_FPGA_CHECK_CTRLC
+#define CONFIG_SYS_FPGA_CHECK_ERROR
+
+/* FPGA program pin configuration */
+#define CONFIG_SYS_FPGA_PRG (GPIO_PORTB | 18) /* FPGA prog pin (SSI output) */
+#define CONFIG_SYS_FPGA_CLK (GPIO_PORTB | 19) /* FPGA clk pin (SSI output) */
+#define CONFIG_SYS_FPGA_DATA (GPIO_PORTB | 17) /* FPGA data pin (SSI output) */
+#define CONFIG_SYS_FPGA_INIT (GPIO_PORTB | 15) /* FPGA init pin (SSI input) */
+#define CONFIG_SYS_FPGA_DONE (GPIO_PORTB | 16) /* FPGA done pin (SSI input) */
+
+/*
+ * I2C bus
+ */
+
+#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
+
+#define CONFIG_SYS_I2C_SPEED 400000 /* 400 kHz */
+#define CONFIG_SYS_I2C_SLAVE 0x7F
+
+# define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM 24LC256 */
+# define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 /* bytes of address */
+/* mask of address bits that overflow into the "EEPROM chip address" */
+/*#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 0x00*/
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* takes up to 10 msec */
+
+#define CONFIG_RTC_DS1374
+/*#define CONFIG_MMC 1
+*/
+/*
+ * External interfaces module
+ *
+ * CSxU_VAL:
+ * 63| x |x|x x|x x x x|x x| x | x |x x x x|48
+ * |DTACK_SEL|0|BCD| BCS |PSZ|PME|SYNC| DOL |
+ *
+ * 47| x x | x x x x x x | x | x x x x | x x x x |32
+ * | CNC | WSC | 0 | WWS | EDC |
+ *
+ * CSxL_VAL:
+ * 31| x x x x | x x x x | x x x x | x x x x |24
+ * | OEA | OEN | WEA | WEN |
+ * 23|x x x x| x | x x x | x x x x |x x| x | x | 0
+ * | CSA |EBC| DSZ | 0|SP|0|WP|0 0|PA |CSEN |
+ */
+
+/* CS0 configuration for flash memory Micron MT28F128J3-150 */
+#define CONFIG_SYS_CS0_CHIP_SELECT_ENABLE 1 /* 1 : enable CS0 peripherals */
+#define CONFIG_SYS_CS0_DATA_PORT_SIZE 0x5 /* 5=16 bits on D[15:0] pins */
+ /* 3=8bits on D[7:0] 6=32 bits..*/
+#define CONFIG_SYS_CS0_SUPERVISOR_PROTECT 0 /* 1 : user mode access prohibited */
+#define CONFIG_SYS_CS0_WRITE_PROTECT 0 /* 1 : write access prohibited */
+#define CONFIG_SYS_CS0_EB_SIGNAL_CONTROL_WRITE 1 /* 1 when EB is used as write signal */
+#define CONFIG_SYS_CS0_READ_CYC_LGTH 150 /* ns */
+#define CONFIG_SYS_CS0_OE_ASSERT_DLY 0 /* ns */
+#define CONFIG_SYS_CS0_OE_NEG_DLY 0 /* ns */
+
+#define CONFIG_SYS_CS0_CS_NEG_LGTH 0 /* ns CS HIGH to CS LOW : tCWH */
+#define CONFIG_SYS_CS0_XTRA_DEAD_CYC 35 /* ns from CS HIGH to tristate bus */
+
+#define CONFIG_SYS_CS0_WRITE_XTRA_LGTH 0 /* ns */
+#define CONFIG_SYS_CS0_EB_ASSERT_DLY 0 /* ns */
+#define CONFIG_SYS_CS0_EB_NEG_DLY 0 /* ns */
+#define CONFIG_SYS_CS0_CS_ASSERT_NEG_DLY 0 /* ns */
+
+#define CONFIG_SYS_CS0_SYNC_ENABLE 1 /* enable synchronous burst mode */
+#define CONFIG_SYS_CS0_SYNC_PAGE_MODE_EMUL 1 /* enable page mode emulation */
+#define CONFIG_SYS_CS0_SYNC_PAGE_SIZE 0 /* 4 words page size (8bytes) */
+#define CONFIG_SYS_CS0_SYNC_BURST_CLK_START 0 /* 0 ns burst clock delay */
+#define CONFIG_SYS_CS0_SYNC_BURST_CLK_DIV 0 /* 0 : divider is 1 */
+#define CONFIG_SYS_CS0_SYNC_DAT_OUT_LGTH 25 /* ns */
+
+/* CS1 configuration for */
+#define CONFIG_SYS_CS1_CHIP_SELECT_ENABLE 1 /* 1 : enable CS0 peripherals */
+#define CONFIG_SYS_CS1_PIN_ASSERT 0 /* chip select pin state when */
+ /* chip select disabled */
+#define CONFIG_SYS_CS1_DATA_PORT_SIZE 0x5 /* 5=16 bits on D[15:0] pins*/
+ /* 3=8bits on D[7:0] 6=32 bits..*/
+#define CONFIG_SYS_CS1_SUPERVISOR_PROTECT 0 /* 1 : user mode access prohibited */
+#define CONFIG_SYS_CS1_WRITE_PROTECT 0 /* 1 : write access prohibited */
+#define CONFIG_SYS_CS1_EB_SIGNAL_CONTROL_WRITE 1 /* 1 when EB is used as write signal */
+
+#define CONFIG_SYS_CS1_READ_CYC_LGTH 50 /* ns */
+#define CONFIG_SYS_CS1_OE_ASSERT_DLY 0 /* ns */
+#define CONFIG_SYS_CS1_OE_NEG_DLY 0 /* ns */
+
+#define CONFIG_SYS_CS1_CS_NEG_LGTH 0 /* max 30 ns CS HIGH to CS LOW at 100MHz */
+#define CONFIG_SYS_CS1_XTRA_DEAD_CYC 0 /* ns from CS HIGH to tristate bus */
+
+#define CONFIG_SYS_CS1_WRITE_XTRA_LGTH 0 /* ns */
+#define CONFIG_SYS_CS1_EB_ASSERT_DLY 0 /* ns */
+#define CONFIG_SYS_CS1_EB_NEG_DLY 0 /* ns */
+#define CONFIG_SYS_CS1_CS_ASSERT_NEG_DLY 0 /* ns */
+
+#define CONFIG_SYS_CS1_SYNC_ENABLE 0 /* enable synchronous burst mode */
+#define CONFIG_SYS_CS1_SYNC_PAGE_MODE_EMUL 0 /* enable page mode emulation */
+#define CONFIG_SYS_CS1_SYNC_PAGE_SIZE 0 /* 4 words page size (8bytes) */
+#define CONFIG_SYS_CS1_SYNC_BURST_CLK_START 0 /* 0 ns burst clock delay */
+#define CONFIG_SYS_CS1_SYNC_BURST_CLK_DIV 0 /* 0 : divider is 1 */
+#define CONFIG_SYS_CS1_SYNC_DAT_OUT_LGTH 0 /* ns */
+
+/* CS2 configuration for */
+#define CONFIG_SYS_CS2_CHIP_SELECT_ENABLE 0 /* 1 : enable CS0 peripherals */
+#define CONFIG_SYS_CS2_PIN_ASSERT 0 /* chip select pin state when */
+ /*chip select disabled */
+#define CONFIG_SYS_CS2_DATA_PORT_SIZE 0x5 /* 5=16 bits on D[15:0] pins */
+ /* 3=8bits on D[7:0] 6=32 bits..*/
+#define CONFIG_SYS_CS2_SUPERVISOR_PROTECT 0 /* 1 : user mode access prohibited */
+#define CONFIG_SYS_CS2_WRITE_PROTECT 0 /* 1 : write access prohibited */
+#define CONFIG_SYS_CS2_EB_SIGNAL_CONTROL_WRITE 1 /* 1 when EB is used as write signal */
+
+#define CONFIG_SYS_CS2_READ_CYC_LGTH 0 /* ns */
+#define CONFIG_SYS_CS2_OE_ASSERT_DLY 0 /* ns */
+#define CONFIG_SYS_CS2_OE_NEG_DLY 0 /* ns */
+
+#define CONFIG_SYS_CS2_CS_NEG_LGTH 0 /* max 30 ns CS HIGH to CS LOW at 100MHz */
+#define CONFIG_SYS_CS2_XTRA_DEAD_CYC 0 /* ns from CS HIGH to tristate bus */
+
+#define CONFIG_SYS_CS2_WRITE_XTRA_LGTH 0 /* ns */
+#define CONFIG_SYS_CS2_EB_ASSERT_DLY 0 /* ns */
+#define CONFIG_SYS_CS2_EB_NEG_DLY 0 /* ns */
+#define CONFIG_SYS_CS2_CS_ASSERT_NEG_DLY 0 /* ns */
+
+#define CONFIG_SYS_CS2_SYNC_ENABLE 0 /* enable synchronous burst mode */
+#define CONFIG_SYS_CS2_SYNC_PAGE_MODE_EMUL 0 /* enable page mode emulation*/
+#define CONFIG_SYS_CS2_SYNC_PAGE_SIZE 0 /* 4 words page size (8bytes) */
+#define CONFIG_SYS_CS2_SYNC_BURST_CLK_START 0 /* 0 ns burst clock delay */
+#define CONFIG_SYS_CS2_SYNC_BURST_CLK_DIV 0 /* 0 : divider is 1 */
+#define CONFIG_SYS_CS2_SYNC_DAT_OUT_LGTH 0 /* ns */
+
+/* CS3 configuration for ISP1760 */
+#define CONFIG_SYS_CS3_CHIP_SELECT_ENABLE 1 /* 1 : enable CS0 peripherals */
+#define CONFIG_SYS_CS3_PIN_ASSERT 0 /* chip select pin state when */
+ /* chip select disabled */
+#define CONFIG_SYS_CS3_DATA_PORT_SIZE 0x5 /* 5=16 bits on D[15:0] pins */
+ /* 3=8bits on D[7:0] 6=32 bits..*/
+#define CONFIG_SYS_CS3_SUPERVISOR_PROTECT 0 /* 1: user mode access prohibited*/
+#define CONFIG_SYS_CS3_WRITE_PROTECT 0 /* 1: write access prohibited */
+#define CONFIG_SYS_CS3_EB_SIGNAL_CONTROL_WRITE 1 /* 1 when EB is used as write signal*/
+
+#define CONFIG_SYS_CS3_READ_CYC_LGTH 110 /* ns */
+#define CONFIG_SYS_CS3_OE_ASSERT_DLY 45 /* ns */
+#define CONFIG_SYS_CS3_OE_NEG_DLY 40 /* ns */
+
+#define CONFIG_SYS_CS3_CS_NEG_LGTH 30 /* max 30 ns CS HIGH to CS LOW at 100MHz */
+#define CONFIG_SYS_CS3_XTRA_DEAD_CYC 0 /* ns from CS HIGH to tristate bus */
+
+#define CONFIG_SYS_CS3_WRITE_XTRA_LGTH 0 /* ns */
+#define CONFIG_SYS_CS3_EB_ASSERT_DLY 45 /* ns */
+#define CONFIG_SYS_CS3_EB_NEG_DLY 45 /* ns */
+#define CONFIG_SYS_CS3_CS_ASSERT_NEG_DLY 35 /* ns */
+
+#define CONFIG_SYS_CS3_SYNC_ENABLE 0 /* enable synchronous burst mode*/
+#define CONFIG_SYS_CS3_SYNC_PAGE_MODE_EMUL 0 /* enable page mode emulation*/
+#define CONFIG_SYS_CS3_SYNC_PAGE_SIZE 0 /* 4 words page size (8bytes) */
+#define CONFIG_SYS_CS3_SYNC_BURST_CLK_START 0 /* 0 ns burst clock delay */
+#define CONFIG_SYS_CS3_SYNC_BURST_CLK_DIV 0 /* 0 : divider is 1 */
+#define CONFIG_SYS_CS3_SYNC_DAT_OUT_LGTH 0 /* ns */
+
+/* CS4 configuration for DM9000 ethernet chipset */
+#define CONFIG_SYS_CS4_CHIP_SELECT_ENABLE 1 /* 1 : enable CS0 peripherals */
+#define CONFIG_SYS_CS4_PIN_ASSERT 0 /* chip select pin state when */
+ /* chip select disabled */
+#define CONFIG_SYS_CS4_DATA_PORT_SIZE 0x5 /* 5=16 bits on D[15:0] pins */
+ /* 3=8bits on D[7:0] 6=32 bits..*/
+#define CONFIG_SYS_CS4_SUPERVISOR_PROTECT 0 /* 1 : user mode access prohibited*/
+#define CONFIG_SYS_CS4_WRITE_PROTECT 0 /* 1 : write access prohibited */
+#define CONFIG_SYS_CS4_EB_SIGNAL_CONTROL_WRITE 1 /* 1 when EB is used as write signal*/
+
+#define CONFIG_SYS_CS4_READ_CYC_LGTH 72 /* ns */
+#define CONFIG_SYS_CS4_OE_ASSERT_DLY 5 /* ns */
+#define CONFIG_SYS_CS4_OE_NEG_DLY 45 /* ns */
+
+#define CONFIG_SYS_CS4_CS_NEG_LGTH 30 /* max 30 ns CS HIGH to CS LOW at 100MHz*/
+#define CONFIG_SYS_CS4_XTRA_DEAD_CYC 0 /* ns from CS HIGH to tristate bus */
+
+#define CONFIG_SYS_CS4_WRITE_XTRA_LGTH 0 /* ns */
+#define CONFIG_SYS_CS4_EB_ASSERT_DLY 5 /* ns */
+#define CONFIG_SYS_CS4_EB_NEG_DLY 45 /* ns */
+#define CONFIG_SYS_CS4_CS_ASSERT_NEG_DLY 0 /* ns */
+
+#define CONFIG_SYS_CS4_SYNC_ENABLE 0 /* enable synchronous burst mode*/
+#define CONFIG_SYS_CS4_SYNC_PAGE_MODE_EMUL 0 /* enable page mode emulation */
+#define CONFIG_SYS_CS4_SYNC_PAGE_SIZE 0 /* 4 words page size (8bytes) */
+#define CONFIG_SYS_CS4_SYNC_BURST_CLK_START 0 /* 0 ns burst clock delay */
+#define CONFIG_SYS_CS4_SYNC_BURST_CLK_DIV 0 /* 0 : divider is 1 */
+#define CONFIG_SYS_CS4_SYNC_DAT_OUT_LGTH 0 /* ns */
+
+/* CS5 configuration for */
+#define CONFIG_SYS_CS5_CHIP_SELECT_ENABLE 1 /* 1 : enable CS0 peripherals */
+#define CONFIG_SYS_CS5_PIN_ASSERT 0 /* chip select pin state when */
+ /* chip select disabled */
+#define CONFIG_SYS_CS5_DATA_PORT_SIZE 0x5 /* 5=16 bits on D[15:0] pins */
+ /* 3=8bits on D[7:0] 6=32 bits..*/
+#define CONFIG_SYS_CS5_SUPERVISOR_PROTECT 0 /* 1: user mode access prohibited*/
+#define CONFIG_SYS_CS5_WRITE_PROTECT 0 /* 1 : write access prohibited*/
+#define CONFIG_SYS_CS5_EB_SIGNAL_CONTROL_WRITE 1 /* 1 when EB is used as write signal*/
+#define CONFIG_SYS_CS5_DTACK_SELECT 1 /* Activate DTACK fonction */
+ /* (asynchrone bus) */
+
+#define CONFIG_SYS_CS5_READ_CYC_LGTH -1 /* ns or -1 to DTACK function */
+#define CONFIG_SYS_CS5_OE_ASSERT_DLY 10 /* ns */
+#define CONFIG_SYS_CS5_OE_NEG_DLY 10 /* ns */
+
+#define CONFIG_SYS_CS5_CS_NEG_LGTH 10 /* max 30 ns CS HIGH to CS LOW at 100MHz*/
+#define CONFIG_SYS_CS5_XTRA_DEAD_CYC 0 /* ns from CS HIGH to tristate bus */
+
+#define CONFIG_SYS_CS5_WRITE_XTRA_LGTH 0 /* ns */
+#define CONFIG_SYS_CS5_EB_ASSERT_DLY 10 /* ns */
+#define CONFIG_SYS_CS5_EB_NEG_DLY 10 /* ns */
+#define CONFIG_SYS_CS5_CS_ASSERT_NEG_DLY 0 /* ns */
+
+#define CONFIG_SYS_CS5_SYNC_ENABLE 0 /* enable synchron burst mode */
+#define CONFIG_SYS_CS5_SYNC_PAGE_MODE_EMUL 0 /* enable page mode emulation */
+#define CONFIG_SYS_CS5_SYNC_PAGE_SIZE 0 /* 4 words page size (8bytes) */
+#define CONFIG_SYS_CS5_SYNC_BURST_CLK_START 0 /* 0 ns burst clock delay */
+#define CONFIG_SYS_CS5_SYNC_BURST_CLK_DIV 0 /* 0 : divider is 1 */
+#define CONFIG_SYS_CS5_SYNC_DAT_OUT_LGTH 0 /* ns */
+
+/*
+ * Default configuration for GPIOs and peripherals
+ */
+#define CONFIG_SYS_DDIR_A_VAL 0x00000000
+#define CONFIG_SYS_OCR1_A_VAL 0x00000000
+#define CONFIG_SYS_OCR2_A_VAL 0x00000000
+#define CONFIG_SYS_ICFA1_A_VAL 0xFFFFFFFF
+#define CONFIG_SYS_ICFA2_A_VAL 0xFFFFFFFF
+#define CONFIG_SYS_ICFB1_A_VAL 0xFFFFFFFF
+#define CONFIG_SYS_ICFB2_A_VAL 0xFFFFFFFF
+#define CONFIG_SYS_DR_A_VAL 0x00000000
+
+/* Setup for PA23 which is Reset Default PA23 but has to become
+ CS5 */
+#define CONFIG_SYS_GIUS_A_VAL 0x00007FF8
+#define CONFIG_SYS_ICR1_A_VAL 0x00000000
+#define CONFIG_SYS_ICR2_A_VAL 0x00000000
+#define CONFIG_SYS_IMR_A_VAL 0x00000000
+#define CONFIG_SYS_GPR_A_VAL 0x00000000
+#define CONFIG_SYS_PUEN_A_VAL 0xFFFFFFFF
+
+#define CONFIG_SYS_DDIR_B_VAL 0x00000000
+#define CONFIG_SYS_OCR1_B_VAL 0x00000000
+#define CONFIG_SYS_OCR2_B_VAL 0x00000000
+#define CONFIG_SYS_ICFA1_B_VAL 0xFFFFFFFF
+#define CONFIG_SYS_ICFA2_B_VAL 0xFFFFFFFF
+#define CONFIG_SYS_ICFB1_B_VAL 0xFFFFFFFF
+#define CONFIG_SYS_ICFB2_B_VAL 0xFFFFFFFF
+#define CONFIG_SYS_DR_B_VAL 0x00000000
+#define CONFIG_SYS_GIUS_B_VAL 0xFFFFFFFF
+#define CONFIG_SYS_ICR1_B_VAL 0x00000000
+#define CONFIG_SYS_ICR2_B_VAL 0x00000000
+#define CONFIG_SYS_IMR_B_VAL 0x00000000
+#define CONFIG_SYS_GPR_B_VAL 0x00000000
+#define CONFIG_SYS_PUEN_B_VAL 0xFFFFFFFF
+
+#define CONFIG_SYS_DDIR_C_VAL 0x00000000
+#define CONFIG_SYS_OCR1_C_VAL 0x00000000
+#define CONFIG_SYS_OCR2_C_VAL 0x00000000
+#define CONFIG_SYS_ICFA1_C_VAL 0xFFFFFFFF
+#define CONFIG_SYS_ICFA2_C_VAL 0xFFFFFFFF
+#define CONFIG_SYS_ICFB1_C_VAL 0xFFFFFFFF
+#define CONFIG_SYS_ICFB2_C_VAL 0xFFFFFFFF
+#define CONFIG_SYS_DR_C_VAL 0x00000000
+#define CONFIG_SYS_GIUS_C_VAL 0x0007FFFF
+#define CONFIG_SYS_ICR1_C_VAL 0x00000000
+#define CONFIG_SYS_ICR2_C_VAL 0x00000000
+#define CONFIG_SYS_IMR_C_VAL 0x00000000
+#define CONFIG_SYS_GPR_C_VAL 0x00000000
+#define CONFIG_SYS_PUEN_C_VAL 0xF913FFFF
+
+#define CONFIG_SYS_DDIR_D_VAL 0x00000000
+#define CONFIG_SYS_OCR1_D_VAL 0x00000000
+#define CONFIG_SYS_OCR2_D_VAL 0x00000000
+#define CONFIG_SYS_ICFA1_D_VAL 0xFFFFFFFF
+#define CONFIG_SYS_ICFA2_D_VAL 0xFFFFFFFF
+#define CONFIG_SYS_ICFB1_D_VAL 0xFFFFFFFF
+#define CONFIG_SYS_ICFB2_D_VAL 0xFFFFFFFF
+#define CONFIG_SYS_DR_D_VAL 0x00000000
+#define CONFIG_SYS_GIUS_D_VAL 0xFFFFFFFF
+#define CONFIG_SYS_ICR1_D_VAL 0x00000000
+#define CONFIG_SYS_ICR2_D_VAL 0x00000000
+#define CONFIG_SYS_IMR_D_VAL 0x00000000
+#define CONFIG_SYS_GPR_D_VAL 0x00000000
+#define CONFIG_SYS_PUEN_D_VAL 0xFFFFFFFF
+
+#define CONFIG_SYS_GPCR_VAL 0x000003AB
+
+/* FMCR Bit 1 becomes 0 to make CS3 if we have only one sdram bank*/
+#if (CONFIG_NR_DRAM_BANKS == 1)
+#define CONFIG_SYS_FMCR_VAL 0x00000001
+#elif (CONFIG_NR_DRAM_BANKS == 2)
+#define CONFIG_SYS_FMCR_VAL 0x00000003
+#endif
+
+/*
+ * FIXME: From here, there should not be any user configuration.
+ * All Equations are automatic
+ */
+
+
+#define CONFIG_SYS_HCLK_LGTH (1000/CONFIG_SYS_BUS_FREQ) /* ns */
+
+/* USB 48 MHz ; BUS 96MHz*/
+#ifdef CONFIG_SYS_OSC16
+#define CSCR_MASK 0x23030003
+#else
+#define CSCR_MASK 0x23000003
+#endif
+#define CONFIG_SYS_CSCR_VAL\
+ (CSCR_MASK \
+ |((((CONFIG_SYS_FREQ/CONFIG_USB_FREQ)-1)&0x07)<<26) \
+ |((((CONFIG_SYS_FREQ/CONFIG_SYS_BUS_FREQ)-1)&0x0F)<<10))
+
+/* PERCLKx 16MHz */
+#define CONFIG_SYS_PCDR_VAL\
+ (((((CONFIG_SYS_FREQ/CONFIG_PERIF1_FREQ)-1)&0x0F)<<0) \
+ |((((CONFIG_SYS_FREQ/CONFIG_PERIF2_FREQ)-1)&0x0F)<<4) \
+ |((((CONFIG_SYS_FREQ/CONFIG_PERIF3_FREQ)-1)&0x7F)<<16))
+
+/* SDRAM controller programming Values */
+#if ((CONFIG_SYS_SDRAM_CLOCK_CYCLE_CL_1>(3*CONFIG_SYS_HCLK_LGTH))\
+ ||(CONFIG_SYS_SDRAM_CLOCK_CYCLE_CL_1<1))
+#define REG_FIELD_SCL_VAL 3
+#else
+#define REG_FIELD_SCL_VAL\
+ ((CONFIG_SYS_SDRAM_CLOCK_CYCLE_CL_1+CONFIG_SYS_HCLK_LGTH-1)/CONFIG_SYS_HCLK_LGTH)
+#endif
+
+#if ((CONFIG_SYS_SDRAM_ROW_PRECHARGE_DELAY>(2*CONFIG_SYS_HCLK_LGTH))\
+ ||(CONFIG_SYS_SDRAM_ROW_PRECHARGE_DELAY<1))
+#define REG_FIELD_SRP_VAL 0
+#else
+#define REG_FIELD_SRP_VAL 1
+#endif
+
+#if (CONFIG_SYS_SDRAM_ROW_2_COL_DELAY>(3*CONFIG_SYS_HCLK_LGTH))
+#define REG_FIELD_SRCD_VAL 0
+#else
+#define REG_FIELD_SRCD_VAL\
+ ((CONFIG_SYS_SDRAM_ROW_2_COL_DELAY+CONFIG_SYS_HCLK_LGTH-1)/CONFIG_SYS_HCLK_LGTH)
+#endif
+
+#if (CONFIG_SYS_SDRAM_ROW_CYCLE_DELAY>(7*CONFIG_SYS_HCLK_LGTH))
+#define REG_FIELD_SRC_VAL 0
+#else
+#define REG_FIELD_SRC_VAL\
+ ((CONFIG_SYS_SDRAM_ROW_CYCLE_DELAY+CONFIG_SYS_HCLK_LGTH-1)/CONFIG_SYS_HCLK_LGTH)
+#endif
+
+#define REG_SDCTL_BASE_CONFIG (0x800a1000\
+ | (((CONFIG_SYS_SDRAM_NUM_ROW-11)&0x3)<<24)\
+ | (((CONFIG_SYS_SDRAM_NUM_COL-8)&0x3)<<20)\
+ | (((CONFIG_SYS_SDRAM_REFRESH)&0x3)<<14)\
+ | (((REG_FIELD_SCL_VAL)&0x3)<<8)\
+ | (((REG_FIELD_SRP_VAL)&0x1)<<6)\
+ | (((REG_FIELD_SRCD_VAL)&0x3)<<4)\
+ | (((REG_FIELD_SRC_VAL)&0x7)<<0))
+
+#define CONFIG_SYS_NORMAL_RW_CMD ((0x0<<28)+REG_SDCTL_BASE_CONFIG)
+#define CONFIG_SYS_PRECHARGE_CMD ((0x1<<28)+REG_SDCTL_BASE_CONFIG)
+#define CONFIG_SYS_AUTOREFRESH_CMD ((0x2<<28)+REG_SDCTL_BASE_CONFIG)
+#define CONFIG_SYS_SET_MODE_REG_CMD ((0x3<<28)+REG_SDCTL_BASE_CONFIG)
+
+/* Issue Mode register Command to SDRAM*/
+#define CONFIG_SYS_SDRAM_MODE_REGISTER_VAL\
+ ((((CONFIG_SYS_SDRAM_BURST_LENGTH)&0x7)<<(CONFIG_SYS_SDRAM_NUM_COL+4))\
+ | (((REG_FIELD_SCL_VAL)&0x3)<<(CONFIG_SYS_SDRAM_NUM_COL+4+4))\
+ | (((CONFIG_SYS_SDRAM_SINGLE_ACCESS)&0x1)<<(CONFIG_SYS_SDRAM_NUM_COL+4+9)))
+
+/* Issue Precharge all Command to SDRAM*/
+#define CONFIG_SYS_SDRAM_PRECHARGE_ALL_VAL\
+ (((CONFIG_SYS_SDRAM_SINGLE_ACCESS)&0x1)<<(CONFIG_SYS_SDRAM_NUM_COL+4+9))
+
+/* undef CONFIG_INIT_CRITICAL is no more required to boot from sdram */
+#undef CONFIG_INIT_CRITICAL
+
+/*
+ * CSxU_VAL:
+ * 63| x |x|x x|x x x x|x x| x | x |x x x x|48
+ * |DTACK_SEL|0|BCD| BCS |PSZ|PME|SYNC| DOL |
+ *
+ * 47| x x | x x x x x x | x | x x x x | x x x x |32
+ * | CNC | WSC | 0 | WWS | EDC |
+ *
+ * CSxL_VAL:
+ * 31| x x x x | x x x x | x x x x | x x x x |24
+ * | OEA | OEN | WEA | WEN |
+ * 23|x x x x| x | x x x | x x x x |x x| x | x | 0
+ * | CSA |EBC| DSZ | 0|SP|0|WP|0 0|PA |CSEN |
+ */
+#define CONFIG_SYS_CS0U_VAL\
+ ((((CONFIG_SYS_CS0_XTRA_DEAD_CYC+CONFIG_SYS_HCLK_LGTH-1)/CONFIG_SYS_HCLK_LGTH)&0x0F)\
+ |((((CONFIG_SYS_CS0_WRITE_XTRA_LGTH+CONFIG_SYS_HCLK_LGTH-1)/CONFIG_SYS_HCLK_LGTH)&0x0F)<<4)\
+ |(((((CONFIG_SYS_CS0_READ_CYC_LGTH+CONFIG_SYS_HCLK_LGTH-1)/CONFIG_SYS_HCLK_LGTH)-1)&0x3F)<<8)\
+ |((((CONFIG_SYS_CS0_CS_NEG_LGTH+CONFIG_SYS_HCLK_LGTH-1)/CONFIG_SYS_HCLK_LGTH)&0x03)<<14)\
+ |((((CONFIG_SYS_CS0_SYNC_DAT_OUT_LGTH+CONFIG_SYS_HCLK_LGTH-1)/CONFIG_SYS_HCLK_LGTH)&0x0F)<<16)\
+ |((CONFIG_SYS_CS0_SYNC_ENABLE&0x01)<<20)\
+ |((CONFIG_SYS_CS0_SYNC_PAGE_MODE_EMUL&0x01)<<21)\
+ |((CONFIG_SYS_CS0_SYNC_PAGE_SIZE&0x03)<<22)\
+ |((((CONFIG_SYS_CS0_SYNC_BURST_CLK_START+CONFIG_SYS_HCLK_LGTH-1)/CONFIG_SYS_HCLK_LGTH)&0x0F)<<24)\
+ |((CONFIG_SYS_CS0_SYNC_BURST_CLK_DIV&0x03)<<28))
+
+#define CONFIG_SYS_CS0L_VAL\
+ ((CONFIG_SYS_CS0_CHIP_SELECT_ENABLE&0x01)\
+ |((CONFIG_SYS_CS0_WRITE_PROTECT&0x01)<<4)\
+ |((CONFIG_SYS_CS0_SUPERVISOR_PROTECT&0x01)<<6)\
+ |((CONFIG_SYS_CS0_DATA_PORT_SIZE&0x07)<<8)\
+ |((CONFIG_SYS_CS0_EB_SIGNAL_CONTROL_WRITE&0x01)<<11)\
+ |((((CONFIG_SYS_CS0_CS_ASSERT_NEG_DLY+CONFIG_SYS_HCLK_LGTH-1)/CONFIG_SYS_HCLK_LGTH)&0x0F)<<12)\
+ |(((((CONFIG_SYS_CS0_EB_NEG_DLY*2)+CONFIG_SYS_HCLK_LGTH-1)/CONFIG_SYS_HCLK_LGTH)&0x0F)<<16)\
+ |(((((CONFIG_SYS_CS0_EB_ASSERT_DLY*2)+CONFIG_SYS_HCLK_LGTH-1)/CONFIG_SYS_HCLK_LGTH)&0x0F)<<20)\
+ |(((((CONFIG_SYS_CS0_OE_NEG_DLY*2)+CONFIG_SYS_HCLK_LGTH-1)/CONFIG_SYS_HCLK_LGTH)&0x0F)<<24)\
+ |(((((CONFIG_SYS_CS0_OE_ASSERT_DLY*2)+CONFIG_SYS_HCLK_LGTH-1)/CONFIG_SYS_HCLK_LGTH)&0x0F)<<28))
+
+#define CONFIG_SYS_CS1U_VAL\
+ ((((CONFIG_SYS_CS1_XTRA_DEAD_CYC+CONFIG_SYS_HCLK_LGTH-1)/CONFIG_SYS_HCLK_LGTH)&0x0F)\
+ |((((CONFIG_SYS_CS1_WRITE_XTRA_LGTH+CONFIG_SYS_HCLK_LGTH-1)/CONFIG_SYS_HCLK_LGTH)&0x0F)<<4)\
+ |(((((CONFIG_SYS_CS1_READ_CYC_LGTH+CONFIG_SYS_HCLK_LGTH-1)/CONFIG_SYS_HCLK_LGTH)-1)&0x3F)<<8)\
+ |((((CONFIG_SYS_CS1_CS_NEG_LGTH+CONFIG_SYS_HCLK_LGTH-1)/CONFIG_SYS_HCLK_LGTH)&0x03)<<14)\
+ |((((CONFIG_SYS_CS1_SYNC_DAT_OUT_LGTH+CONFIG_SYS_HCLK_LGTH-1)/CONFIG_SYS_HCLK_LGTH)&0x0F)<<16)\
+ |((CONFIG_SYS_CS1_SYNC_ENABLE&0x01)<<20)\
+ |((CONFIG_SYS_CS1_SYNC_PAGE_MODE_EMUL&0x01)<<21)\
+ |((CONFIG_SYS_CS1_SYNC_PAGE_SIZE&0x03)<<22)\
+ |((((CONFIG_SYS_CS1_SYNC_BURST_CLK_START+CONFIG_SYS_HCLK_LGTH-1)/CONFIG_SYS_HCLK_LGTH)&0x0F)<<24)\
+ |((CONFIG_SYS_CS1_SYNC_BURST_CLK_DIV&0x03)<<28))
+
+#define CONFIG_SYS_CS1L_VAL\
+ ((CONFIG_SYS_CS1_CHIP_SELECT_ENABLE&0x01)\
+ |((CONFIG_SYS_CS1_PIN_ASSERT&0x01)<<1)\
+ |((CONFIG_SYS_CS1_WRITE_PROTECT&0x01)<<4)\
+ |((CONFIG_SYS_CS1_SUPERVISOR_PROTECT&0x01)<<6)\
+ |((CONFIG_SYS_CS1_DATA_PORT_SIZE&0x07)<<8)\
+ |((CONFIG_SYS_CS1_EB_SIGNAL_CONTROL_WRITE&0x01)<<11)\
+ |((((CONFIG_SYS_CS1_CS_ASSERT_NEG_DLY+CONFIG_SYS_HCLK_LGTH-1)/CONFIG_SYS_HCLK_LGTH)&0x0F)<<12)\
+ |(((((CONFIG_SYS_CS1_EB_NEG_DLY*2)+CONFIG_SYS_HCLK_LGTH-1)/CONFIG_SYS_HCLK_LGTH)&0x0F)<<16)\
+ |(((((CONFIG_SYS_CS1_EB_ASSERT_DLY*2)+CONFIG_SYS_HCLK_LGTH-1)/CONFIG_SYS_HCLK_LGTH)&0x0F)<<20)\
+ |(((((CONFIG_SYS_CS1_OE_NEG_DLY*2)+CONFIG_SYS_HCLK_LGTH-1)/CONFIG_SYS_HCLK_LGTH)&0x0F)<<24)\
+ |(((((CONFIG_SYS_CS1_OE_ASSERT_DLY*2)+CONFIG_SYS_HCLK_LGTH-1)/CONFIG_SYS_HCLK_LGTH)&0x0F)<<28))
+
+#define CONFIG_SYS_CS2U_VAL\
+ (((((CONFIG_SYS_CS2_XTRA_DEAD_CYC+CONFIG_SYS_HCLK_LGTH-1)/CONFIG_SYS_HCLK_LGTH)&0x0F)\
+ |((((CONFIG_SYS_CS2_WRITE_XTRA_LGTH+CONFIG_SYS_HCLK_LGTH-1)/CONFIG_SYS_HCLK_LGTH)&0x0F)<<4)\
+ |(((((CONFIG_SYS_CS2_READ_CYC_LGTH+CONFIG_SYS_HCLK_LGTH-1)/CONFIG_SYS_HCLK_LGTH)-1)&0x3F)<<8)\
+ |((((CONFIG_SYS_CS2_CS_NEG_LGTH+CONFIG_SYS_HCLK_LGTH-1)/CONFIG_SYS_HCLK_LGTH)&0x03)<<14)\
+ |(((CONFIG_SYS_CS2_SYNC_DAT_OUT_LGTH+CONFIG_SYS_HCLK_LGTH-1)/CONFIG_SYS_HCLK_LGTH)&0x0F)<<16)\
+ |((CONFIG_SYS_CS2_SYNC_ENABLE&0x01)<<20)\
+ |((CONFIG_SYS_CS2_SYNC_PAGE_MODE_EMUL&0x01)<<21)\
+ |((CONFIG_SYS_CS2_SYNC_PAGE_SIZE&0x03)<<22)\
+ |((((CONFIG_SYS_CS2_SYNC_BURST_CLK_START+CONFIG_SYS_HCLK_LGTH-1)/CONFIG_SYS_HCLK_LGTH)&0x0F)<<24)\
+ |((CONFIG_SYS_CS2_SYNC_BURST_CLK_DIV&0x03)<<28))
+
+#define CONFIG_SYS_CS2L_VAL\
+ ((CONFIG_SYS_CS2_CHIP_SELECT_ENABLE&0x01)\
+ |((CONFIG_SYS_CS2_PIN_ASSERT&0x01)<<1)\
+ |((CONFIG_SYS_CS2_WRITE_PROTECT&0x01)<<4)\
+ |((CONFIG_SYS_CS2_SUPERVISOR_PROTECT&0x01)<<6)\
+ |((CONFIG_SYS_CS2_DATA_PORT_SIZE&0x07)<<8)\
+ |((CONFIG_SYS_CS2_EB_SIGNAL_CONTROL_WRITE&0x01)<<11)\
+ |((((CONFIG_SYS_CS2_CS_ASSERT_NEG_DLY+CONFIG_SYS_HCLK_LGTH-1)/CONFIG_SYS_HCLK_LGTH)&0x0F)<<12)\
+ |(((((CONFIG_SYS_CS2_EB_NEG_DLY*2)+CONFIG_SYS_HCLK_LGTH-1)/CONFIG_SYS_HCLK_LGTH)&0x0F)<<16)\
+ |(((((CONFIG_SYS_CS2_EB_ASSERT_DLY*2)+CONFIG_SYS_HCLK_LGTH-1)/CONFIG_SYS_HCLK_LGTH)&0x0F)<<20)\
+ |(((((CONFIG_SYS_CS2_OE_NEG_DLY*2)+CONFIG_SYS_HCLK_LGTH-1)/CONFIG_SYS_HCLK_LGTH)&0x0F)<<24)\
+ |(((((CONFIG_SYS_CS2_OE_ASSERT_DLY*2)+CONFIG_SYS_HCLK_LGTH-1)/CONFIG_SYS_HCLK_LGTH)&0x0F)<<28))
+
+#define CONFIG_SYS_CS3U_VAL\
+ ((((CONFIG_SYS_CS3_XTRA_DEAD_CYC+CONFIG_SYS_HCLK_LGTH-1)/CONFIG_SYS_HCLK_LGTH)&0x0F)\
+ |((((CONFIG_SYS_CS3_WRITE_XTRA_LGTH+CONFIG_SYS_HCLK_LGTH-1)/CONFIG_SYS_HCLK_LGTH)&0x0F)<<4)\
+ |(((((CONFIG_SYS_CS3_READ_CYC_LGTH+CONFIG_SYS_HCLK_LGTH-1)/CONFIG_SYS_HCLK_LGTH)-1)&0x3F)<<8)\
+ |((((CONFIG_SYS_CS3_CS_NEG_LGTH+CONFIG_SYS_HCLK_LGTH-1)/CONFIG_SYS_HCLK_LGTH)&0x03)<<14)\
+ |((((CONFIG_SYS_CS3_SYNC_DAT_OUT_LGTH+CONFIG_SYS_HCLK_LGTH-1)/CONFIG_SYS_HCLK_LGTH)&0x0F)<<16)\
+ |((CONFIG_SYS_CS3_SYNC_ENABLE&0x01)<<20)\
+ |((CONFIG_SYS_CS3_SYNC_PAGE_MODE_EMUL&0x01)<<21)\
+ |((CONFIG_SYS_CS3_SYNC_PAGE_SIZE&0x03)<<22)\
+ |((((CONFIG_SYS_CS3_SYNC_BURST_CLK_START+CONFIG_SYS_HCLK_LGTH-1)/CONFIG_SYS_HCLK_LGTH)&0x0F)<<24)\
+ |((CONFIG_SYS_CS3_SYNC_BURST_CLK_DIV&0x03)<<28))
+
+#define CONFIG_SYS_CS3L_VAL\
+ ((CONFIG_SYS_CS3_CHIP_SELECT_ENABLE&0x01)\
+ |((CONFIG_SYS_CS3_PIN_ASSERT&0x01)<<1)\
+ |((CONFIG_SYS_CS3_WRITE_PROTECT&0x01)<<4)\
+ |((CONFIG_SYS_CS3_SUPERVISOR_PROTECT&0x01)<<6)\
+ |((CONFIG_SYS_CS3_DATA_PORT_SIZE&0x07)<<8)\
+ |((CONFIG_SYS_CS3_EB_SIGNAL_CONTROL_WRITE&0x01)<<11)\
+ |((((CONFIG_SYS_CS3_CS_ASSERT_NEG_DLY+CONFIG_SYS_HCLK_LGTH-1)/CONFIG_SYS_HCLK_LGTH)&0x0F)<<12)\
+ |(((((CONFIG_SYS_CS3_EB_NEG_DLY*2)+CONFIG_SYS_HCLK_LGTH-1)/CONFIG_SYS_HCLK_LGTH)&0x0F)<<16)\
+ |(((((CONFIG_SYS_CS3_EB_ASSERT_DLY*2)+CONFIG_SYS_HCLK_LGTH-1)/CONFIG_SYS_HCLK_LGTH)&0x0F)<<20)\
+ |(((((CONFIG_SYS_CS3_OE_NEG_DLY*2)+CONFIG_SYS_HCLK_LGTH-1)/CONFIG_SYS_HCLK_LGTH)&0x0F)<<24)\
+ |(((((CONFIG_SYS_CS3_OE_ASSERT_DLY*2)+CONFIG_SYS_HCLK_LGTH-1)/CONFIG_SYS_HCLK_LGTH)&0x0F)<<28))
+
+#define CONFIG_SYS_CS4U_VAL\
+ (((((CONFIG_SYS_CS4_XTRA_DEAD_CYC+CONFIG_SYS_HCLK_LGTH-1)/CONFIG_SYS_HCLK_LGTH)&0x0F)\
+ |((((CONFIG_SYS_CS4_WRITE_XTRA_LGTH+CONFIG_SYS_HCLK_LGTH-1)/CONFIG_SYS_HCLK_LGTH)&0x0F)<<4)\
+ |(((((CONFIG_SYS_CS4_READ_CYC_LGTH+CONFIG_SYS_HCLK_LGTH-1)/CONFIG_SYS_HCLK_LGTH)-1)&0x3F)<<8)\
+ |((((CONFIG_SYS_CS4_CS_NEG_LGTH+CONFIG_SYS_HCLK_LGTH-1)/CONFIG_SYS_HCLK_LGTH)&0x03)<<14)\
+ |((((CONFIG_SYS_CS4_SYNC_DAT_OUT_LGTH+CONFIG_SYS_HCLK_LGTH-1)/CONFIG_SYS_HCLK_LGTH)&0x0F)<<16))\
+ |((CONFIG_SYS_CS4_SYNC_ENABLE&0x01)<<20)\
+ |((CONFIG_SYS_CS4_SYNC_PAGE_MODE_EMUL&0x01)<<21)\
+ |((CONFIG_SYS_CS4_SYNC_PAGE_SIZE&0x03)<<22)\
+ |((((CONFIG_SYS_CS4_SYNC_BURST_CLK_START+CONFIG_SYS_HCLK_LGTH-1)/CONFIG_SYS_HCLK_LGTH)&0x0F)<<24)\
+ |((CONFIG_SYS_CS4_SYNC_BURST_CLK_DIV&0x03)<<28))
+
+#define CONFIG_SYS_CS4L_VAL\
+ ((CONFIG_SYS_CS4_CHIP_SELECT_ENABLE&0x01)\
+ |((CONFIG_SYS_CS4_PIN_ASSERT&0x01)<<1)\
+ |((CONFIG_SYS_CS4_WRITE_PROTECT&0x01)<<4)\
+ |((CONFIG_SYS_CS4_SUPERVISOR_PROTECT&0x01)<<6)\
+ |((CONFIG_SYS_CS4_DATA_PORT_SIZE&0x07)<<8)\
+ |((CONFIG_SYS_CS4_EB_SIGNAL_CONTROL_WRITE&0x01)<<11)\
+ |((((CONFIG_SYS_CS4_CS_ASSERT_NEG_DLY+CONFIG_SYS_HCLK_LGTH-1)/CONFIG_SYS_HCLK_LGTH)&0x0F)<<12)\
+ |(((((CONFIG_SYS_CS4_EB_NEG_DLY*2)+CONFIG_SYS_HCLK_LGTH-1)/CONFIG_SYS_HCLK_LGTH)&0x0F)<<16)\
+ |(((((CONFIG_SYS_CS4_EB_ASSERT_DLY*2)+CONFIG_SYS_HCLK_LGTH-1)/CONFIG_SYS_HCLK_LGTH)&0x0F)<<20)\
+ |(((((CONFIG_SYS_CS4_OE_NEG_DLY*2)+CONFIG_SYS_HCLK_LGTH-1)/CONFIG_SYS_HCLK_LGTH)&0x0F)<<24)\
+ |(((((CONFIG_SYS_CS4_OE_ASSERT_DLY*2)+CONFIG_SYS_HCLK_LGTH-1)/CONFIG_SYS_HCLK_LGTH)&0x0F)<<28))
+
+#define CONFIG_SYS_CS5U_VAL\
+ ((((CONFIG_SYS_CS5_XTRA_DEAD_CYC+CONFIG_SYS_HCLK_LGTH-1)/CONFIG_SYS_HCLK_LGTH)&0x0F)\
+ |((((CONFIG_SYS_CS5_WRITE_XTRA_LGTH+CONFIG_SYS_HCLK_LGTH-1)/CONFIG_SYS_HCLK_LGTH)&0x0F)<<4)\
+ |(((((CONFIG_SYS_CS5_READ_CYC_LGTH+CONFIG_SYS_HCLK_LGTH-1)/CONFIG_SYS_HCLK_LGTH)-1)&0x3F)<<8)\
+ |((((CONFIG_SYS_CS5_CS_NEG_LGTH+CONFIG_SYS_HCLK_LGTH-1)/CONFIG_SYS_HCLK_LGTH)&0x03)<<14)\
+ |((((CONFIG_SYS_CS5_SYNC_DAT_OUT_LGTH+CONFIG_SYS_HCLK_LGTH-1)/CONFIG_SYS_HCLK_LGTH)&0x0F)<<16)\
+ |((CONFIG_SYS_CS5_SYNC_ENABLE&0x01)<<20)\
+ |((CONFIG_SYS_CS5_SYNC_PAGE_MODE_EMUL&0x01)<<21)\
+ |((CONFIG_SYS_CS5_SYNC_PAGE_SIZE&0x03)<<22)\
+ |((((CONFIG_SYS_CS5_SYNC_BURST_CLK_START+CONFIG_SYS_HCLK_LGTH-1)/CONFIG_SYS_HCLK_LGTH)&0x0F)<<24)\
+ |((CONFIG_SYS_CS5_SYNC_BURST_CLK_DIV&0x03)<<28)\
+ |((CONFIG_SYS_CS5_DTACK_SELECT&0x01)<<31))
+
+#define CONFIG_SYS_CS5L_VAL\
+ ((CONFIG_SYS_CS5_CHIP_SELECT_ENABLE&0x01)\
+ |((CONFIG_SYS_CS5_PIN_ASSERT&0x01)<<1)\
+ |((CONFIG_SYS_CS5_WRITE_PROTECT&0x01)<<4)\
+ |((CONFIG_SYS_CS5_SUPERVISOR_PROTECT&0x01)<<6)\
+ |((CONFIG_SYS_CS5_DATA_PORT_SIZE&0x07)<<8)\
+ |((CONFIG_SYS_CS5_EB_SIGNAL_CONTROL_WRITE&0x01)<<11)\
+ |((((CONFIG_SYS_CS5_CS_ASSERT_NEG_DLY+CONFIG_SYS_HCLK_LGTH-1)/CONFIG_SYS_HCLK_LGTH)&0x0F)<<12)\
+ |(((((CONFIG_SYS_CS5_EB_NEG_DLY*2)+CONFIG_SYS_HCLK_LGTH-1)/CONFIG_SYS_HCLK_LGTH)&0x0F)<<16)\
+ |(((((CONFIG_SYS_CS5_EB_ASSERT_DLY*2)+CONFIG_SYS_HCLK_LGTH-1)/CONFIG_SYS_HCLK_LGTH)&0x0F)<<20)\
+ |(((((CONFIG_SYS_CS5_OE_NEG_DLY*2)+CONFIG_SYS_HCLK_LGTH-1)/CONFIG_SYS_HCLK_LGTH)&0x0F)<<24)\
+ |(((((CONFIG_SYS_CS5_OE_ASSERT_DLY*2)+CONFIG_SYS_HCLK_LGTH-1)/CONFIG_SYS_HCLK_LGTH)&0x0F)<<28))
+
+#endif /* __CONFIG_H */
diff --git a/buildroot/target/device/armadeus/apf9328/apf9328_defconfig b/buildroot/target/device/armadeus/apf9328/apf9328_defconfig
index 52783a4..07bb0e6 100644
--- a/buildroot/target/device/armadeus/apf9328/apf9328_defconfig
+++ b/buildroot/target/device/armadeus/apf9328/apf9328_defconfig
@@ -126,7 +126,7 @@ BR2_TOPDIR_SUFFIX=""
BR2_ROOTFS_PREFIX="$(BR2_BOARD_NAME)-rootfs"
BR2_ROOTFS_SUFFIX=""
BR2_GNU_BUILD_SUFFIX="pc-linux-gnu"
-BR2_GNU_TARGET_SUFFIX="linux-uclibc"
+BR2_GNU_TARGET_SUFFIX="linux-uclibcgnueabi"
BR2_JLEVEL=1
# BR2_PREFER_IMA is not set
# BR2_DEPRECATED is not set
@@ -769,6 +769,18 @@ BR2_TARGET_ROOTFS_TAR_COPYTO=""
BR2_TARGET_UBOOT=y
BR2_TARGET_UBOOT_BOARDNAME="$(BR2_BOARD_NAME)"
BR2_TARGET_U_BOOT_CONFIG_HEADER_FILE="$(BR2_BOARD_PATH)/$(BR2_BOARD_NAME).h"
+BR2_TARGET_UBOOT_1_3_4=y
+# BR2_TARGET_UBOOT_2010_03 is not set
+# BR2_TARGET_UBOOT_2009_11 is not set
+# BR2_TARGET_UBOOT_2009_08 is not set
+# BR2_TARGET_UBOOT_2009_06 is not set
+# BR2_TARGET_UBOOT_2009_03 is not set
+# BR2_TARGET_UBOOT_2009_01 is not set
+# BR2_TARGET_UBOOT_2008_10 is not set
+# BR2_TARGET_UBOOT_1_2_0_ATMEL is not set
+BR2_UBOOT_VERSION="1.3.4"
+BR2_U_BOOT_SITE="ftp://ftp.denx.de/pub/u-boot"
+# BR2_TARGET_U_BOOT_ARCH_PATCH is not set
BR2_TARGET_UBOOT_CUSTOM_PATCH=""
BR2_TARGET_UBOOT_SERVERIP=""
BR2_TARGET_UBOOT_IPADDR=""
diff --git a/buildroot/target/u-boot/u-boot-1.3.4-100-imx.patch b/buildroot/target/u-boot/u-boot-2010.03-rc2-100-imx.patch
similarity index 74%
copy from buildroot/target/u-boot/u-boot-1.3.4-100-imx.patch
copy to buildroot/target/u-boot/u-boot-2010.03-rc2-100-imx.patch
index ff779bd..01dcaca 100644
--- a/buildroot/target/u-boot/u-boot-1.3.4-100-imx.patch
+++ b/buildroot/target/u-boot/u-boot-2010.03-rc2-100-imx.patch
@@ -1,18 +1,27 @@
-diff -purN u-boot-1.3.4.ref/cpu/arm920t/imx/interrupts.c u-boot-1.3.4/cpu/arm920t/imx/interrupts.c
---- u-boot-1.3.4.ref/cpu/arm920t/imx/interrupts.c 2008-08-12 16:08:38.000000000 +0200
-+++ u-boot-1.3.4/cpu/arm920t/imx/interrupts.c 2008-09-13 16:16:58.000000000 +0200
-@@ -60,7 +60,7 @@ void reset_timer (void)
+--- u-boot-2010.03-rc2/cpu/arm920t/imx/timer.c.ori 2010-03-22 23:25:00.000000000 +0100
++++ u-boot-2010.03-rc2/cpu/arm920t/imx/timer.c 2010-03-30 22:35:41.000000000 +0200
+@@ -75,16 +75,16 @@ void reset_timer_masked (void)
- ulong get_timer (ulong base)
+ ulong get_timer_masked (void)
{
-- return get_timer_masked ();
-+ return get_timer_masked () - base;
+- return TCN1;
++ return TCN1/1000l;
}
- void set_timer (ulong t)
-diff -purN u-boot-1.3.4.ref/cpu/arm920t/imx/speed.c u-boot-1.3.4/cpu/arm920t/imx/speed.c
---- u-boot-1.3.4.ref/cpu/arm920t/imx/speed.c 2008-08-12 16:08:38.000000000 +0200
-+++ u-boot-1.3.4/cpu/arm920t/imx/speed.c 2008-09-13 16:16:58.000000000 +0200
+ void udelay_masked (unsigned long usec)
+ {
+- ulong endtime = get_timer_masked() + usec;
++ ulong endtime = TCN1 + usec;
+ signed long diff;
+
+ do {
+- ulong now = get_timer_masked ();
++ ulong now = TCN1;
+ diff = endtime - now;
+ } while (diff >= 0);
+ }
+--- u-boot.ref/cpu/arm920t/imx/speed.c 2008-08-12 16:08:38.000000000 +0200
++++ u-boot/cpu/arm920t/imx/speed.c 2008-09-13 16:16:58.000000000 +0200
@@ -36,33 +36,27 @@
* the specified bus in HZ.
*/
@@ -67,9 +76,8 @@ diff -purN u-boot-1.3.4.ref/cpu/arm920t/imx/speed.c u-boot-1.3.4/cpu/arm920t/imx
return get_systemPLLCLK() / bclkdiv;
}
-diff -purN u-boot-1.3.4.ref/include/asm-arm/arch-imx/imx-regs.h u-boot-1.3.4/include/asm-arm/arch-imx/imx-regs.h
---- u-boot-1.3.4.ref/include/asm-arm/arch-imx/imx-regs.h 2008-08-12 16:08:38.000000000 +0200
-+++ u-boot-1.3.4/include/asm-arm/arch-imx/imx-regs.h 2008-09-13 16:16:58.000000000 +0200
+--- u-boot.ref/include/asm-arm/arch-imx/imx-regs.h 2008-08-12 16:08:38.000000000 +0200
++++ u-boot/include/asm-arm/arch-imx/imx-regs.h 2008-09-13 16:16:58.000000000 +0200
@@ -631,4 +631,27 @@
#define TSTAT_CAPT (1<<1) /* Capture event */
#define TSTAT_COMP (1) /* Compare event */
diff --git a/buildroot/target/u-boot/u-boot-1.3.4-110-apf9328.patch b/buildroot/target/u-boot/u-boot-2010.03-rc2-110-apf9328.patch
similarity index 83%
copy from buildroot/target/u-boot/u-boot-1.3.4-110-apf9328.patch
copy to buildroot/target/u-boot/u-boot-2010.03-rc2-110-apf9328.patch
index c282d4e..0e214f6 100644
--- a/buildroot/target/u-boot/u-boot-1.3.4-110-apf9328.patch
+++ b/buildroot/target/u-boot/u-boot-2010.03-rc2-110-apf9328.patch
@@ -1,5 +1,5 @@
---- ref/u-boot-1.3.4/board/armadeus/apf9328/apf9328.c 1970-01-01 01:00:00.000000000 +0100
-+++ u-boot-1.3.4/board/armadeus/apf9328/apf9328.c 2008-11-14 00:48:19.000000000 +0100
+--- ref/u-boot/board/armadeus/apf9328/apf9328.c 1970-01-01 01:00:00.000000000 +0100
++++ u-boot/board/armadeus/apf9328/apf9328.c 2008-11-14 00:48:19.000000000 +0100
@@ -0,0 +1,101 @@
+/*
+ * Copyright (C) 2004 Sascha Hauer, Synertronixx GmbH
@@ -26,7 +26,7 @@
+#include "apf9328fpga.h"
+
+extern void imx_gpio_mode (int gpio_mode);
-+#if (CFG_FLASH_CFI) && (CFG_FLASH_CFI_DRIVER)
++#if (CONFIG_FLASH_CFI_DRIVER)
+extern flash_info_t flash_info[];
+#endif
+int
@@ -49,12 +49,12 @@
+ DECLARE_GLOBAL_DATA_PTR;
+
+#if ( CONFIG_NR_DRAM_BANKS > 0 )
-+ gd->bd->bi_dram[0].start = CFG_SDRAM_1_BASE;
-+ gd->bd->bi_dram[0].size = CFG_SDRAM_1_SIZE;
++ gd->bd->bi_dram[0].start = CONFIG_SYS_SDRAM_1_BASE;
++ gd->bd->bi_dram[0].size = CONFIG_SYS_SDRAM_1_SIZE;
+#endif
+#if ( CONFIG_NR_DRAM_BANKS > 1 )
-+ gd->bd->bi_dram[1].start = CFG_SDRAM_2_BASE;
-+ gd->bd->bi_dram[1].size = CFG_SDRAM_2_SIZE;
++ gd->bd->bi_dram[1].start = CONFIG_SYS_SDRAM_2_BASE;
++ gd->bd->bi_dram[1].size = CONFIG_SYS_SDRAM_2_SIZE;
+#endif
+
+ return 0;
@@ -77,12 +77,12 @@
+#endif
+
+ /* adjust size of rootfs if needed */
-+#if (CFG_FLASH_CFI) && (CFG_FLASH_CFI_DRIVER)
++#if (CONFIG_FLASH_CFI_DRIVER)
+ s = getenv ("rootfs_len");
+ if (( NULL == s ) || (0 == strcmp(s, ""))) {
+ char rootfslen[16];
+ sprintf (rootfslen, "0x%lX", flash_info[0].size -
-+ (CONFIG_ROOTFS_ADDR - CFG_FLASH_BASE));
++ (CONFIG_ROOTFS_ADDR - CONFIG_SYS_FLASH_BASE));
+ setenv ("rootfs_len", rootfslen);
+ }
+#endif
@@ -102,8 +102,8 @@
+{
+ return;
+}
---- ref/u-boot-1.3.4/board/armadeus/apf9328/apf9328fpga.c 1970-01-01 01:00:00.000000000 +0100
-+++ u-boot-1.3.4/board/armadeus/apf9328/apf9328fpga.c 2008-11-14 00:48:19.000000000 +0100
+--- ref/u-boot/board/armadeus/apf9328/apf9328fpga.c 1970-01-01 01:00:00.000000000 +0100
++++ u-boot/board/armadeus/apf9328/apf9328fpga.c 2008-11-14 00:48:19.000000000 +0100
@@ -0,0 +1,100 @@
+/*
+ * (C) Copyright 2005
@@ -184,10 +184,10 @@
+ DECLARE_GLOBAL_DATA_PTR;
+
+ int i,lout=1;
-+
++/*
+ PRINTF ("%s:%d: Initialize FPGA interface (relocation offset = 0x%.8lx)\n",
+ __FUNCTION__, __LINE__, gd->reloc_off);
-+ fpga_init (gd->reloc_off);
++*/ fpga_init ();
+
+ for (i = 0; i < CONFIG_FPGA_COUNT; i++) {
+ PRINTF ("%s:%d: Adding fpga %d\n", __FUNCTION__, __LINE__, i);
@@ -205,8 +205,8 @@
+}
+
+#endif /* CONFIG_FPGA */
---- ref/u-boot-1.3.4/board/armadeus/apf9328/apf9328fpga.h 1970-01-01 01:00:00.000000000 +0100
-+++ u-boot-1.3.4/board/armadeus/apf9328/apf9328fpga.h 2008-11-14 00:48:19.000000000 +0100
+--- ref/u-boot/board/armadeus/apf9328/apf9328fpga.h 1970-01-01 01:00:00.000000000 +0100
++++ u-boot/board/armadeus/apf9328/apf9328fpga.h 2008-11-14 00:48:19.000000000 +0100
@@ -0,0 +1,31 @@
+/*
+ * (C) Copyright 2002
@@ -239,8 +239,8 @@
+
+#include "fpga.h"
+extern int apf9328_init_fpga (void);
---- ref/u-boot-1.3.4/board/armadeus/apf9328/config.mk 1970-01-01 01:00:00.000000000 +0100
-+++ u-boot-1.3.4/board/armadeus/apf9328/config.mk 2008-11-14 00:48:19.000000000 +0100
+--- ref/u-boot/board/armadeus/apf9328/config.mk 1970-01-01 01:00:00.000000000 +0100
++++ u-boot/board/armadeus/apf9328/config.mk 2008-11-14 00:48:19.000000000 +0100
@@ -0,0 +1,10 @@
+#
+# This config file is used for compilation of armadeus sources
@@ -252,8 +252,8 @@
+#
+
+TEXT_BASE = 0x0BF80000
---- ref/u-boot-1.3.4/board/armadeus/apf9328/fpga.c 1970-01-01 01:00:00.000000000 +0100
-+++ u-boot-1.3.4/board/armadeus/apf9328/fpga.c 2008-11-14 00:48:19.000000000 +0100
+--- ref/u-boot/board/armadeus/apf9328/fpga.c 1970-01-01 01:00:00.000000000 +0100
++++ u-boot/board/armadeus/apf9328/fpga.c 2008-11-14 00:48:19.000000000 +0100
@@ -0,0 +1,140 @@
+/*
+ * (C) Copyright 2002
@@ -309,11 +309,11 @@
+/*
+ * Port bit numbers for the serial slave controls
+ */
-+#define FPGA_INIT CFG_FPGA_INIT
-+#define FPGA_DONE CFG_FPGA_DONE
-+#define FPGA_DIN CFG_FPGA_DATA
-+#define FPGA_PROGRAM CFG_FPGA_PRG
-+#define FPGA_CLOCK CFG_FPGA_CLK
++#define FPGA_INIT CONFIG_SYS_FPGA_INIT
++#define FPGA_DONE CONFIG_SYS_FPGA_DONE
++#define FPGA_DIN CONFIG_SYS_FPGA_DATA
++#define FPGA_PROGRAM CONFIG_SYS_FPGA_PRG
++#define FPGA_CLOCK CONFIG_SYS_FPGA_CLK
+
+/* Note that these are pointers to code that is in Flash. They will be
+ * relocated at runtime.
@@ -395,8 +395,8 @@
+}
+
+#endif /* CONFIG_FPGA */
---- ref/u-boot-1.3.4/board/armadeus/apf9328/fpga.h 1970-01-01 01:00:00.000000000 +0100
-+++ u-boot-1.3.4/board/armadeus/apf9328/fpga.h 2008-11-14 00:48:19.000000000 +0100
+--- ref/u-boot/board/armadeus/apf9328/fpga.h 1970-01-01 01:00:00.000000000 +0100
++++ u-boot/board/armadeus/apf9328/fpga.h 2008-11-14 00:48:19.000000000 +0100
@@ -0,0 +1,30 @@
+/*
+ * (C) Copyright 2002
@@ -428,9 +428,9 @@
+extern int fpga_done_fn (int cookie);
+extern int fpga_clk_fn (int assert_clk, int flush, int cookie);
+extern int fpga_wr_fn (int assert_write, int flush, int cookie);
---- ref/u-boot-1.3.4/board/armadeus/apf9328/i2c.c 1970-01-01 01:00:00.000000000 +0100
-+++ u-boot-1.3.4/board/armadeus/apf9328/i2c.c 2008-11-14 00:48:19.000000000 +0100
-@@ -0,0 +1,327 @@
+--- ref/u-boot/board/armadeus/apf9328/i2c.c 1970-01-01 01:00:00.000000000 +0100
++++ u-boot/board/armadeus/apf9328/i2c.c 2008-11-14 00:48:19.000000000 +0100
+@@ -0,0 +1,305 @@
+/*
+ * Eric Jarrige <jo...@us...>
+ *
@@ -633,7 +633,7 @@
+ PRINTD ("i2c_read: chip %02X addr %02X alen %d buffer %p len %d\n",
+ chip, addr, alen, buffer, len);
+
-+#ifdef CFG_I2C_EEPROM_ADDR_OVERFLOW
++#ifdef CONFIG_SYS_I2C_EEPROM_ADD...
[truncated message content] |
