Menu
▾
▴
RE: [ACPI] Re: Fw: Anybody? 2.6.11 (stable and -rc) ACPI breaks USB
|
From: Li, S. <sha...@in...> - 2005-03-14 09:30:58
|
Hi, This issue is quite interesting. We removed all specific VIA quirk recently and apply a generic VIA quirk. But in this case, the MCH 00:0.0 is from AMD, and the ISA bridge and built-in devices are from VIA, this means VIA quirk is useless, since it takes action only when the MCH is from VIA. We possibly should enable VIA quirk if a VIA ISA bridge is found instead of a VIA MCH found, but Bjorn's method seems ok. If you want to put the patch into kernel, please also change the ' pirq_enable_irq' case. Thanks, Shaohua >-----Original Message----- >From: acp...@li... [mailto:acpi-devel- >ad...@li...] On Behalf Of Grzegorz Kulewski >Sent: Sunday, March 13, 2005 11:15 PM >To: Bjorn Helgaas >Cc: Andrew Morton; ACPI List; lkml >Subject: Re: [ACPI] Re: Fw: Anybody? 2.6.11 (stable and -rc) ACPI breaks >USB > >On Fri, 11 Mar 2005, Bjorn Helgaas wrote: > >> Can you do an "lspci -vvn"? I'm looking at quirk_via_irqpic() in >> 2.6.9, which is what printed this: >> >>>> PCI: Via IRQ fixup for 0000:00:07.2, from 9 to 10 >>>> PCI: Via IRQ fixup for 0000:00:07.3, from 9 to 10 >> >> but it looks like it should only run for PCI_DEVICE_ID_VIA_82C586_2, >> PCI_DEVICE_ID_VIA_82C686_5, and PCI_DEVICE_ID_VIA_82C686_6. >> >> You have: >> >> 0000:00:07.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super >South] (rev 40) >> 0000:00:07.1 IDE interface: VIA Technologies, Inc. >VT82C586A/B/VT82C686/A/B/VT8233/A/C/VT8235 PIPC Bus Master IDE (rev 06) >> 0000:00:07.2 USB Controller: VIA Technologies, Inc. USB (rev 1a) (prog-if >00 [UHCI]) >> 0000:00:07.3 USB Controller: VIA Technologies, Inc. USB (rev 1a) (prog-if >00 [UHCI]) >> >> and we apparently ran the quirk for 07.2 and 07.3. I wouldn't >> have thought those would have one of the above device IDs. The >> "lspci -vvn" should tell us for sure. >> >> 2.6.11 removed that quirk and runs quirk_via_bridge() for >> all VIA devices, but only sets via_interrupt_line_quirk if >> (pdev->devfn =3D=3D 0), which you don't have. So that's why >> my patch didn't do anything. >> >>> Also two more questions: >>> >>> 1. What is VIA fixup? Is it some hardware bug? Or BIOS problem? Why is >it >>> needed? On what hardware / software it is needed? >> >> I really don't know much about the VIA fixup. I just noticed >> that we seem to be doing it slightly differently in 2.6.11 than >> we did in 2.6.9, and thought maybe it was related to your problem. >> Here's a changeset that has a couple pointers: >> >> http://linux.bkbits.net:8080/linux- >2.5/cset%4041cb9d48DRV4TYe77gvstTawuZFYyQ >> >>> 2. Why this patch shrinked bzImage that much: >>> >>> -rw-r--r-- 1 root root 1828186 mar 11 23:33 vmlinuz-2.6.11-cko1 >>> -rw-r--r-- 1 root root 1828355 mar 2 20:48 vmlinuz-2.6.11-cko1.old >> >> I have no idea about this. But it's only a couple hundred bytes. >> >> So here's another patch to try (revert the first one, then apply this). >> >> =3D=3D=3D=3D=3D drivers/acpi/pci_irq.c 1.37 vs edited =3D=3D=3D=3D=3D >> --- 1.37/drivers/acpi/pci_irq.c 2005-03-01 09:57:29 -07:00 >> +++ edited/drivers/acpi/pci_irq.c 2005-03-11 15:13:49 -07:00 >> @@ -30,6 +30,7 @@ >> #include <linux/module.h> >> #include <linux/init.h> >> #include <linux/types.h> >> +#include <linux/delay.h> >> #include <linux/proc_fs.h> >> #include <linux/spinlock.h> >> #include <linux/pm.h> >> @@ -438,10 +439,17 @@ >> } >> } >> >> - if (via_interrupt_line_quirk) >> - pci_write_config_byte(dev, PCI_INTERRUPT_LINE, irq & 15); >> - >> dev->irq =3D acpi_register_gsi(irq, edge_level, active_high_low); >> + >> + if (dev->vendor =3D=3D PCI_VENDOR_ID_VIA) { >> + u8 old_irq, new_irq =3D dev->irq & 0xf; >> + >> + pci_read_config_byte(dev, PCI_INTERRUPT_LINE, &old_irq); >> + printk(KERN_INFO PREFIX "Via IRQ fixup for %s, from %d " >> + "to %d\n", pci_name(dev), old_irq, new_irq); >> + udelay(15); >> + pci_write_config_byte(dev, PCI_INTERRUPT_LINE, new_irq); >> + } >> >> printk(KERN_INFO PREFIX "PCI interrupt %s[%c] -> GSI %u " >> "(%s, %s) -> IRQ %d\n", >> > >Ok, this patch works. Here is the log: > >Mar 13 17:16:17 kangur Linux version 2.6.11-cko1 (root@kangur) (gcc >version 3.3.3 20040412 (Gentoo Linux 3.3.3-r6, ssp-3.3.2-2, pie-8.7.6)) #3 >Sun Mar 13 17:10:10 CET 2005 >Mar 13 17:16:17 kangur BIOS-provided physical RAM map: >Mar 13 17:16:17 kangur BIOS-e820: 0000000000000000 - 000000000009fc00 >(usable) >Mar 13 17:16:17 kangur BIOS-e820: 000000000009fc00 - 00000000000a0000 >(reserved) >Mar 13 17:16:17 kangur BIOS-e820: 00000000000f0000 - 0000000000100000 >(reserved) >Mar 13 17:16:17 kangur BIOS-e820: 0000000000100000 - 000000001fff0000 >(usable) >Mar 13 17:16:17 kangur BIOS-e820: 000000001fff0000 - 000000001fff3000 >(ACPI NVS) >Mar 13 17:16:17 kangur BIOS-e820: 000000001fff3000 - 0000000020000000 >(ACPI data) >Mar 13 17:16:17 kangur BIOS-e820: 00000000ffff0000 - 0000000100000000 >(reserved) >Mar 13 17:16:17 kangur 511MB LOWMEM available. >Mar 13 17:16:17 kangur On node 0 totalpages: 131056 >Mar 13 17:16:17 kangur DMA zone: 4096 pages, LIFO batch:1 >Mar 13 17:16:17 kangur Normal zone: 126960 pages, LIFO batch:16 >Mar 13 17:16:17 kangur HighMem zone: 0 pages, LIFO batch:1 >Mar 13 17:16:17 kangur DMI 2.2 present. >Mar 13 17:16:17 kangur ACPI: RSDP (v000 761686 >) @ 0x000f6a70 >Mar 13 17:16:17 kangur ACPI: RSDT (v001 761686 AWRDACPI 0x42302e31 AWRD >0x00000000) @ 0x1fff3000 >Mar 13 17:16:17 kangur ACPI: FADT (v001 761686 AWRDACPI 0x42302e31 AWRD >0x00000000) @ 0x1fff3040 >Mar 13 17:16:17 kangur ACPI: DSDT (v001 761686 AWRDACPI 0x00001000 MSFT >0x0100000c) @ 0x00000000 >Mar 13 17:16:17 kangur ACPI: PM-Timer IO Port: 0x4008 >Mar 13 17:16:17 kangur Allocating PCI resources starting at 20000000 (gap: >20000000:dfff0000) >Mar 13 17:16:17 kangur Built 1 zonelists >Mar 13 17:16:17 kangur Kernel command line: ro root=3D/dev/hdb4 >Mar 13 17:16:17 kangur Local APIC disabled by BIOS -- you can enable it >with "lapic" >Mar 13 17:16:17 kangur mapped APIC to ffffd000 (01402000) >Mar 13 17:16:17 kangur Initializing CPU#0 >Mar 13 17:16:17 kangur CPU 0 irqstacks, hard=3Db0477000 soft=3Db0476000 >Mar 13 17:16:17 kangur PID hash table entries: 2048 (order: 11, 32768 >bytes) >Mar 13 17:16:17 kangur Detected 1203.036 MHz processor. >Mar 13 17:16:17 kangur Using pmtmr for high-res timesource >Mar 13 17:16:17 kangur Console: colour VGA+ 80x25 >Mar 13 17:16:17 kangur Dentry cache hash table entries: 131072 (order: 7, >524288 bytes) >Mar 13 17:16:17 kangur Inode-cache hash table entries: 65536 (order: 6, >262144 bytes) >Mar 13 17:16:17 kangur Memory: 514940k/524224k available (2543k kernel >code, 8732k reserved, 819k data, 156k init, 0k highmem) >Mar 13 17:16:17 kangur Checking if this processor honours the WP bit even >in supervisor mode... Ok. >Mar 13 17:16:17 kangur Calibrating delay loop... 2375.68 BogoMIPS >(lpj=3D1187840) >Mar 13 17:16:17 kangur Security Framework v1.0.0 initialized >Mar 13 17:16:17 kangur Capability LSM initialized >Mar 13 17:16:17 kangur Mount-cache hash table entries: 512 (order: 0, 4096 >bytes) >Mar 13 17:16:17 kangur CPU: After generic identify, caps: 0383f9ff >c1cbf9ff 00000000 00000000 00000000 00000000 00000000Mar 13 17:16:17 >kangur CPU: After vendor identify, caps: 0383f9ff c1cbf9ff 00000000 >00000000 00000000 00000000 00000000 >Mar 13 17:16:17 kangur CPU: CLK_CTL MSR was 60071263. Reprogramming to >20071263 >Mar 13 17:16:17 kangur CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K >(64 bytes/line) >Mar 13 17:16:17 kangur CPU: L2 Cache: 512K (64 bytes/line) >Mar 13 17:16:17 kangur CPU: After all inits, caps: 0383f9ff c1cbf9ff >00000000 00000020 00000000 00000000 00000000 >Mar 13 17:16:17 kangur Intel machine check architecture supported. >Mar 13 17:16:17 kangur Intel machine check reporting enabled on CPU#0. >Mar 13 17:16:17 kangur CPU: AMD Unknown CPU Type stepping 00 >Mar 13 17:16:17 kangur Enabling fast FPU save and restore... done. >Mar 13 17:16:17 kangur Enabling unmasked SIMD FPU exception support... >done. >Mar 13 17:16:17 kangur Checking 'hlt' instruction... OK. >Mar 13 17:16:17 kangur ACPI: setting ELCR to 0800 (from 0e20) >Mar 13 17:16:17 kangur NET: Registered protocol family 16 >Mar 13 17:16:17 kangur PCI: PCI BIOS revision 2.10 entry at 0xfb690, last >bus=3D1 >Mar 13 17:16:17 kangur PCI: Using configuration type 1 >Mar 13 17:16:17 kangur mtrr: v2.0 (20020519) >Mar 13 17:16:17 kangur ACPI: Subsystem revision 20050211 >Mar 13 17:16:17 kangur ACPI: Interpreter enabled >Mar 13 17:16:17 kangur ACPI: Using PIC for interrupt routing >Mar 13 17:16:17 kangur ACPI: PCI Root Bridge [PCI0] (00:00) >Mar 13 17:16:17 kangur PCI: Probing PCI hardware (bus 00) >Mar 13 17:16:17 kangur ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] >Mar 13 17:16:17 kangur ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 >*10 11 12 14 15) >Mar 13 17:16:17 kangur ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 >10 *11 12 14 15) >Mar 13 17:16:17 kangur ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 *5 6 7 >10 11 12 14 15) >Mar 13 17:16:17 kangur ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 >10 11 12 14 15) *9 >Mar 13 17:16:17 kangur Linux Plug and Play Support v0.97 (c) Adam Belay >Mar 13 17:16:17 kangur pnp: PnP ACPI init >Mar 13 17:16:17 kangur pnp: PnP ACPI: found 12 devices >Mar 13 17:16:17 kangur SCSI subsystem initialized >Mar 13 17:16:17 kangur PCI: Using ACPI for IRQ routing >Mar 13 17:16:17 kangur ** PCI interrupts are no longer routed >automatically. If this >Mar 13 17:16:17 kangur ** causes a device to stop working, it is probably >because the >Mar 13 17:16:17 kangur ** driver failed to call pci_enable_device(). As a >temporary >Mar 13 17:16:17 kangur ** workaround, the "pci=3Drouteirq" argument restores >the old >Mar 13 17:16:17 kangur ** behavior. If this argument makes the device >work again, >Mar 13 17:16:17 kangur ** please email the output of "lspci" to >bjo...@hp... >Mar 13 17:16:17 kangur ** so I can fix the driver. >Mar 13 17:16:17 kangur pnp: the driver 'system' has been registered >Mar 13 17:16:17 kangur pnp: match found with the PnP device '00:00' and >the driver 'system' >Mar 13 17:16:17 kangur pnp: match found with the PnP device '00:01' and >the driver 'system' >Mar 13 17:16:17 kangur Total HugeTLB memory allocated, 0 >Mar 13 17:16:17 kangur VFS: Disk quotas dquot_6.5.1 >Mar 13 17:16:17 kangur Dquot-cache hash table entries: 1024 (order 0, 4096 >bytes) >Mar 13 17:16:17 kangur SGI XFS with ACLs, security attributes, realtime, >no debug enabled >Mar 13 17:16:17 kangur SGI XFS Quota Management subsystem >Mar 13 17:16:17 kangur Initializing Cryptographic API >Mar 13 17:16:17 kangur inotify device minor=3D63 >Mar 13 17:16:17 kangur ACPI: PS/2 Keyboard Controller [PS2K] at I/O 0x60, >0x64, irq 1 >Mar 13 17:16:17 kangur ACPI: PS/2 Mouse Controller [PS2M] at irq 12 >Mar 13 17:16:17 kangur serio: i8042 AUX port at 0x60,0x64 irq 12 >Mar 13 17:16:17 kangur serio: i8042 KBD port at 0x60,0x64 irq 1 >Mar 13 17:16:17 kangur io scheduler noop registered >Mar 13 17:16:17 kangur io scheduler anticipatory registered >Mar 13 17:16:17 kangur io scheduler deadline registered >Mar 13 17:16:17 kangur io scheduler cfq registered >Mar 13 17:16:17 kangur 8139too Fast Ethernet driver 0.9.27 >Mar 13 17:16:17 kangur ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11 >Mar 13 17:16:17 kangur PCI: setting IRQ 11 as level-triggered >Mar 13 17:16:17 kangur ACPI: PCI interrupt 0000:00:0f.0[A] -> GSI 11 >(level, low) -> IRQ 11 >Mar 13 17:16:17 kangur eth0: RealTek RTL8139 at 0xec00, 00:06:4f:00:73:8b, >IRQ 11 >Mar 13 17:16:17 kangur eth0: Identified 8139 chip type 'RTL-8139C' >Mar 13 17:16:17 kangur Uniform Multi-Platform E-IDE driver Revision: >7.00alpha2 >Mar 13 17:16:17 kangur ide: Assuming 33MHz system bus speed for PIO modes; >override with idebus=3Dxx >Mar 13 17:16:17 kangur VP_IDE: IDE controller at PCI slot 0000:00:07.1 >Mar 13 17:16:17 kangur VP_IDE: chipset revision 6 >Mar 13 17:16:17 kangur VP_IDE: not 100% native mode: will probe irqs later >Mar 13 17:16:17 kangur VP_IDE: VIA vt82c686b (rev 40) IDE UDMA100 >controller on pci0000:00:07.1 >Mar 13 17:16:17 kangur ide0: BM-DMA at 0xc400-0xc407, BIOS settings: >hda:pio, hdb:DMA >Mar 13 17:16:17 kangur ide1: BM-DMA at 0xc408-0xc40f, BIOS settings: >hdc:pio, hdd:DMA >Mar 13 17:16:17 kangur Probing IDE interface ide0... >Mar 13 17:16:17 kangur hdb: SAMSUNG SV3063H, ATA DISK drive >Mar 13 17:16:17 kangur ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 >Mar 13 17:16:17 kangur Probing IDE interface ide1... >Mar 13 17:16:17 kangur hdd: HL-DT-ST DVDRAM GSA-4082B, ATAPI CD/DVD-ROM >drive >Mar 13 17:16:17 kangur ide1 at 0x170-0x177,0x376 on irq 15 >Mar 13 17:16:17 kangur pnp: the driver 'ide' has been registered >Mar 13 17:16:17 kangur hdb: max request size: 128KiB >Mar 13 17:16:17 kangur hdb: 59797584 sectors (30616 MB) w/426KiB Cache, >CHS=3D59323/16/63, UDMA(100) >Mar 13 17:16:17 kangur hdb: cache flushes not supported >Mar 13 17:16:17 kangur hdb: hdb1 hdb2 hdb3 hdb4 >Mar 13 17:16:17 kangur libata version 1.10 loaded. >Mar 13 17:16:17 kangur sata_sil version 0.8 >Mar 13 17:16:17 kangur ACPI: PCI interrupt 0000:00:0d.0[A] -> GSI 11 >(level, low) -> IRQ 11 >Mar 13 17:16:17 kangur ata1: SATA max UDMA/100 cmd 0xD0802080 ctl >0xD080208A bmdma 0xD0802000 irq 11 >Mar 13 17:16:17 kangur ata2: SATA max UDMA/100 cmd 0xD08020C0 ctl >0xD08020CA bmdma 0xD0802008 irq 11 >Mar 13 17:16:17 kangur ata1: dev 0 cfg 49:2f00 82:346b 83:7f61 84:4003 >85:3469 86:3c41 87:4003 88:207f >Mar 13 17:16:17 kangur ata1: dev 0 ATA, max UDMA/133, 312581808 sectors: >lba48 >Mar 13 17:16:17 kangur ata1: dev 0 configured for UDMA/100 >Mar 13 17:16:17 kangur scsi0 : sata_sil >Mar 13 17:16:17 kangur ata2: no device found (phy stat 00000000) >Mar 13 17:16:17 kangur scsi1 : sata_sil >Mar 13 17:16:17 kangur Vendor: ATA Model: WDC WD1600JD-00H Rev: >08.0 >Mar 13 17:16:17 kangur Type: Direct-Access ANSI >SCSI revision: 05 >Mar 13 17:16:17 kangur SCSI device sda: 312581808 512-byte hdwr sectors >(160042 MB) >Mar 13 17:16:17 kangur SCSI device sda: drive cache: write back >Mar 13 17:16:17 kangur SCSI device sda: 312581808 512-byte hdwr sectors >(160042 MB) >Mar 13 17:16:17 kangur SCSI device sda: drive cache: write back >Mar 13 17:16:17 kangur sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 sda8 sda9 >sda10 sda11 sda12 sda13 sda14 sda15 > >Mar 13 17:16:17 kangur Attached scsi disk sda at scsi0, channel 0, id 0, >lun 0 >Mar 13 17:16:17 kangur mice: PS/2 mouse device common for all mice >Mar 13 17:16:17 kangur input: AT Translated Set 2 keyboard on >isa0060/serio0 >Mar 13 17:16:17 kangur NET: Registered protocol family 2 >Mar 13 17:16:17 kangur IP: routing cache hash table of 4096 buckets, >32Kbytes >Mar 13 17:16:17 kangur TCP established hash table entries: 32768 (order: >6, 262144 bytes) >Mar 13 17:16:17 kangur TCP bind hash table entries: 32768 (order: 5, >131072 bytes) >Mar 13 17:16:17 kangur TCP: Hash tables configured (established 32768 bind >32768) >Mar 13 17:16:17 kangur ip_conntrack version 2.1 (4095 buckets, 32760 max) >- 216 bytes per conntrack >Mar 13 17:16:17 kangur ip_tables: (C) 2000-2002 Netfilter core team >Mar 13 17:16:17 kangur ipt_recent v0.3.1: Stephen Frost ><sf...@sn...>. http://snowman.net/projects/ipt_recent/ >Mar 13 17:16:17 kangur arp_tables: (C) 2002 David S. Miller >Mar 13 17:16:17 kangur NET: Registered protocol family 17 >Mar 13 17:16:17 kangur ACPI wakeup devices: >Mar 13 17:16:17 kangur SLPB PCI0 USB0 USB1 >Mar 13 17:16:17 kangur ACPI: (supports S0 S1 S4 S5) >Mar 13 17:16:17 kangur kjournald starting. Commit interval 5 seconds >Mar 13 17:16:17 kangur EXT3-fs: mounted filesystem with ordered data mode. >Mar 13 17:16:17 kangur VFS: Mounted root (ext3 filesystem) readonly. >Mar 13 17:16:17 kangur Freeing unused kernel memory: 156k freed >Mar 13 17:16:17 kangur NET: Registered protocol family 1 >Mar 13 17:16:17 kangur EXT3 FS on hdb4, internal journal >Mar 13 17:16:17 kangur NET: Registered protocol family 8 >Mar 13 17:16:17 kangur NET: Registered protocol family 20 >Mar 13 17:16:17 kangur CSLIP: code copyright 1989 Regents of the >University of California >Mar 13 17:16:17 kangur PPP generic driver version 2.4.2 >Mar 13 17:16:17 kangur input: PS/2 Generic Mouse on isa0060/serio1 >Mar 13 17:16:17 kangur input: PC Speaker >Mar 13 17:16:17 kangur loop: loaded (max 8 devices) >Mar 13 17:16:17 kangur Non-volatile memory driver v1.2 >Mar 13 17:16:17 kangur BIOS EDD facility v0.16 2004-Jun-25, 2 devices >found >Mar 13 17:16:17 kangur vesafb: NVidia Corporation, NV15 Reference Board, >Chip Rev A0 (OEM: NVidia) >Mar 13 17:16:17 kangur vesafb: VBE version: 3.0 >Mar 13 17:16:17 kangur vesafb: protected mode interface info at c000:0f03 >Mar 13 17:16:17 kangur vesafb: pmi: set display start =3D b00c0f3c, set >palette =3D b00c0fb2 >Mar 13 17:16:17 kangur vesafb: pmi: ports =3D 3b4 3b5 3ba 3c0 3c1 3c4 = 3c5 >3c6 3c7 3c8 3c9 3cc 3ce 3cf 3d0 3d1 3d2 3d3 3d4 3d5 3da >Mar 13 17:16:17 kangur vesafb: hardware supports DCC2 transfers >Mar 13 17:16:17 kangur vesafb: monitor limits: vf =3D 85 Hz, hf =3D 64 = kHz, >clk =3D 108 MHz >Mar 13 17:16:17 kangur vesafb: scrolling: redraw >Mar 13 17:16:17 kangur vesafb: framebuffer at 0xe8000000, mapped to >0xd0900000, using 6144k, total 65536k >Mar 13 17:16:17 kangur fb0: VESA VGA frame buffer device >Mar 13 17:16:17 kangur Console: switching to colour frame buffer device >128x48 >Mar 13 17:16:17 kangur device-mapper: 4.4.0-ioctl (2005-01-12) >initialised: dm-...@re... >Mar 13 17:16:17 kangur NTFS driver 2.1.22 [Flags: R/O MODULE]. >Mar 13 17:16:17 kangur NTFS volume version 3.1. >Mar 13 17:16:17 kangur NTFS volume version 3.1. >Mar 13 17:16:17 kangur usbcore: registered new driver usbfs >Mar 13 17:16:17 kangur usbcore: registered new driver hub >Mar 13 17:16:17 kangur ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 10 >Mar 13 17:16:17 kangur PCI: setting IRQ 10 as level-triggered >Mar 13 17:16:17 kangur ACPI: PCI interrupt 0000:00:0b.0[A] -> GSI 10 >(level, low) -> IRQ 10 >Mar 13 17:16:17 kangur parport_pc: VIA 686A/8231 detected >Mar 13 17:16:17 kangur parport_pc: probing current configuration >Mar 13 17:16:17 kangur parport_pc: Current parallel port base: 0x378 >Mar 13 17:16:17 kangur parport_pc: Strange, can't probe VIA parallel port: >io=3D0x378, irq=3D7, dma=3D-1 >Mar 13 17:16:17 kangur pnp: the driver 'parport_pc' has been registered >Mar 13 17:16:17 kangur pnp: match found with the PnP device '00:09' and >the driver 'parport_pc' >Mar 13 17:16:17 kangur parport: PnPBIOS parport detected. >Mar 13 17:16:17 kangur parport0: PC-style at 0x378, irq 7 [PCSPP(,...)] >Mar 13 17:16:17 kangur USB Universal Host Controller Interface driver v2.2 >Mar 13 17:16:17 kangur ACPI: Via IRQ fixup for 0000:00:07.2, from 9 to 10 >Mar 13 17:16:17 kangur ACPI: PCI interrupt 0000:00:07.2[D] -> GSI 10 >(level, low) -> IRQ 10 >Mar 13 17:16:17 kangur uhci_hcd 0000:00:07.2: UHCI Host Controller >Mar 13 17:16:17 kangur uhci_hcd 0000:00:07.2: irq 10, io base 0xc800 >Mar 13 17:16:17 kangur uhci_hcd 0000:00:07.2: new USB bus registered, >assigned bus number 1 >Mar 13 17:16:17 kangur hub 1-0:1.0: USB hub found >Mar 13 17:16:17 kangur hub 1-0:1.0: 2 ports detected >Mar 13 17:16:17 kangur ACPI: Via IRQ fixup for 0000:00:07.3, from 9 to 10 >Mar 13 17:16:17 kangur ACPI: PCI interrupt 0000:00:07.3[D] -> GSI 10 >(level, low) -> IRQ 10 >Mar 13 17:16:17 kangur uhci_hcd 0000:00:07.3: UHCI Host Controller >Mar 13 17:16:17 kangur uhci_hcd 0000:00:07.3: irq 10, io base 0xcc00 >Mar 13 17:16:17 kangur uhci_hcd 0000:00:07.3: new USB bus registered, >assigned bus number 2 >Mar 13 17:16:17 kangur hub 2-0:1.0: USB hub found >Mar 13 17:16:17 kangur hub 2-0:1.0: 2 ports detected >Mar 13 17:16:17 kangur usb 1-2: new full speed USB device using uhci_hcd >and address 2 >Mar 13 17:16:17 kangur Linux video capture interface: v1.00 >Mar 13 17:16:17 kangur bttv: driver version 0.9.15 loaded >Mar 13 17:16:17 kangur bttv: using 32 buffers with 2080k (520 pages) each >for capture >Mar 13 17:16:17 kangur bttv: Bt8xx card found (0). >Mar 13 17:16:17 kangur ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 5 >Mar 13 17:16:17 kangur PCI: setting IRQ 5 as level-triggered >Mar 13 17:16:17 kangur ACPI: PCI interrupt 0000:00:09.0[A] -> GSI 5 >(level, low) -> IRQ 5 >Mar 13 17:16:17 kangur bttv0: Bt878 (rev 17) at 0000:00:09.0, irq: 5, >latency: 32, mmio: 0xf7000000 >Mar 13 17:16:17 kangur bttv0: using: Prolink Pixelview PV-BT878P+ >(Rev.4C,8E) [card=3D70,insmod option] >Mar 13 17:16:17 kangur bttv0: gpio: en=3D00000000, out=3D00000000 in=3D00ffc0ff >[init] >Mar 13 17:16:17 kangur bttv0: using tuner=3D25 >Mar 13 17:16:17 kangur bttv0: i2c: checking for MSP34xx @ 0x80... not >found >Mar 13 17:16:17 kangur bttv0: i2c: checking for TDA9875 @ 0xb0... not >found >Mar 13 17:16:17 kangur bttv0: i2c: checking for TDA7432 @ 0x8a... not >found >Mar 13 17:16:17 kangur tvaudio: TV audio decoder + audio/video mux driver >Mar 13 17:16:17 kangur tvaudio: known chips: >tda9840,tda9873h,tda9874h/a,tda9850,tda9855,tea6300,tea6320,tea6420,tda 8425 >,pic16c54 >(PV951),ta8874z >Mar 13 17:16:17 kangur bttv0: i2c: checking for TDA9887 @ 0x86... not >found >Mar 13 17:16:17 kangur tuner 0-0061: chip found @ 0xc2 (bt878 #0 [sw]) >Mar 13 17:16:17 kangur tuner 0-0061: type set to 25 (LG PAL_I+FM >(TAPC-I001D)) >Mar 13 17:16:17 kangur bttv0: registered device video0 >Mar 13 17:16:17 kangur bttv0: registered device vbi0 >Mar 13 17:16:17 kangur bttv0: registered device radio0 >Mar 13 17:16:17 kangur bttv0: PLL: 28636363 =3D> 35468950 .. ok >Mar 13 17:16:17 kangur bttv0: add subdevice "remote0" >Mar 13 17:16:17 kangur usb 1-2: modprobe timed out on ep0in >Mar 13 17:16:17 kangur usbcore: registered new driver speedtch >Mar 13 17:16:17 kangur usb 1-2: found stage 1 firmware speedtch-1.bin >Mar 13 17:16:17 kangur gameport: pci0000:00:0b.1 speed 1242 kHz >Mar 13 17:16:17 kangur nvidia: module license 'NVIDIA' taints kernel. >Mar 13 17:16:17 kangur ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 10 >Mar 13 17:16:17 kangur ACPI: PCI interrupt 0000:01:05.0[A] -> GSI 10 >(level, low) -> IRQ 10 >Mar 13 17:16:17 kangur NVRM: loading NVIDIA Linux x86 NVIDIA Kernel Module >1.0-6629 Wed Nov 3 13:12:51 PST 2004 >Mar 13 17:16:17 kangur usb 1-2: found stage 2 firmware speedtch-2.bin >Mar 13 17:16:17 kangur Real Time Clock Driver v1.12 >Mar 13 17:16:17 kangur Floppy drive(s): fd0 is 1.44M >Mar 13 17:16:17 kangur FDC 0 is a post-1991 82077 >Mar 13 17:16:17 kangur Serial: 8250/16550 driver $Revision: 1.90 $ 8 >ports, IRQ sharing disabled >Mar 13 17:16:17 kangur ttyS0 at I/O 0x3f8 (irq =3D 4) is a 16550A >Mar 13 17:16:17 kangur ttyS1 at I/O 0x2f8 (irq =3D 3) is a 16550A >Mar 13 17:16:17 kangur pnp: the driver 'serial' has been registered >Mar 13 17:16:17 kangur pnp: match found with the PnP device '00:07' and >the driver 'serial' >Mar 13 17:16:17 kangur ttyS0 at I/O 0x3f8 (irq =3D 4) is a 16550A >Mar 13 17:16:17 kangur pnp: match found with the PnP device '00:08' and >the driver 'serial' >Mar 13 17:16:17 kangur ttyS1 at I/O 0x2f8 (irq =3D 3) is a 16550A >Mar 13 17:16:17 kangur ADSL line is synchronising >Mar 13 17:16:19 kangur eth0: link down >Mar 13 17:16:19 kangur eth0: link down >Mar 13 17:16:20 kangur NET: Registered protocol family 10 >Mar 13 17:16:20 kangur Disabled Privacy Extensions on device b03e7aa0(lo) >Mar 13 17:16:20 kangur IPv6 over IPv4 tunneling driver > > >It generated the following warning: > CC drivers/acpi/pci_irq.o >drivers/acpi/pci_irq.c: In function `acpi_pci_irq_enable': >drivers/acpi/pci_irq.c:392: warning: unused variable >`via_interrupt_line_quirk' > >(I think this warning is new). > >The lspci: > ># lspci -vvn >0000:00:00.0 Class 0600: 1022:700e (rev 13) > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- >ParErr- Stepping- SERR- FastB2B- > Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=3Dmedium >TAbort- ><TAbort- <MAbort+ >SERR- <PERR- > Latency: 32 > Region 0: Memory at f0000000 (32-bit, prefetchable) > Region 1: Memory at f7003000 (32-bit, prefetchable) = [size=3D4K] > Region 2: I/O ports at c000 [disabled] [size=3D4] > Capabilities: [a0] AGP version 2.0 > Status: RQ=3D16 Iso- ArqSz=3D0 Cal=3D0 SBA+ ITACoh- = GART64- >HTrans- 64bit- FW+ AGP3- Rate=3Dx1,x2,x4 > Command: RQ=3D1 ArqSz=3D0 Cal=3D0 SBA+ AGP+ GART64- = 64bit- FW+ >Rate=3Dx4 > >0000:00:01.0 Class 0604: 1022:700f > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- >ParErr- Stepping- SERR+ FastB2B- > Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=3Dmedium >TAbort- ><TAbort- <MAbort- >SERR- <PERR- > Latency: 32 > Bus: primary=3D00, secondary=3D01, subordinate=3D01, = sec-latency=3D32 > Memory behind bridge: f4000000-f5ffffff > Prefetchable memory behind bridge: e8000000-efffffff > BridgeCtl: Parity- SERR+ NoISA+ VGA+ MAbort- >Reset- FastB2B- > >0000:00:07.0 Class 0601: 1106:0686 (rev 40) > Subsystem: 147b:a702 > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- >ParErr- Stepping+ SERR- FastB2B- > Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=3Dmedium >TAbort- ><TAbort- <MAbort- >SERR- <PERR- > Latency: 0 > Capabilities: [c0] Power Management version 2 > Flags: PMEClk- DSI- D1- D2- AuxCurrent=3D0mA >PME(D0-,D1-,D2-,D3hot-,D3cold-) > Status: D0 PME-Enable- DSel=3D0 DScale=3D0 PME- > >0000:00:07.1 Class 0101: 1106:0571 (rev 06) (prog-if 8a [Master SecP >PriP]) > Subsystem: 1106:0571 > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- >ParErr- Stepping- SERR- FastB2B- > Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=3Dmedium >TAbort- ><TAbort- <MAbort- >SERR- <PERR- > Latency: 32 > Region 4: I/O ports at c400 [size=3D16] > Capabilities: [c0] Power Management version 2 > Flags: PMEClk- DSI- D1- D2- AuxCurrent=3D0mA >PME(D0-,D1-,D2-,D3hot-,D3cold-) > Status: D0 PME-Enable- DSel=3D0 DScale=3D0 PME- > >0000:00:07.2 Class 0c03: 1106:3038 (rev 1a) > Subsystem: 0925:1234 > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- >ParErr- Stepping- SERR- FastB2B- > Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=3Dmedium >TAbort- ><TAbort- <MAbort- >SERR- <PERR- > Latency: 32, cache line size 08 > Interrupt: pin D routed to IRQ 10 > Region 4: I/O ports at c800 [size=3D32] > Capabilities: [80] Power Management version 2 > Flags: PMEClk- DSI- D1- D2- AuxCurrent=3D0mA >PME(D0-,D1-,D2-,D3hot-,D3cold-) > Status: D0 PME-Enable- DSel=3D0 DScale=3D0 PME- > >0000:00:07.3 Class 0c03: 1106:3038 (rev 1a) > Subsystem: 0925:1234 > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- >ParErr- Stepping- SERR- FastB2B- > Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=3Dmedium >TAbort- ><TAbort- <MAbort- >SERR- <PERR- > Latency: 32, cache line size 08 > Interrupt: pin D routed to IRQ 10 > Region 4: I/O ports at cc00 [size=3D32] > Capabilities: [80] Power Management version 2 > Flags: PMEClk- DSI- D1- D2- AuxCurrent=3D0mA >PME(D0-,D1-,D2-,D3hot-,D3cold-) > Status: D0 PME-Enable- DSel=3D0 DScale=3D0 PME- > >0000:00:07.4 Class 0c05: 1106:3057 (rev 40) > Subsystem: 1106:3057 > Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- >ParErr- Stepping- SERR- FastB2B- > Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=3Dmedium >TAbort- ><TAbort- <MAbort- >SERR- <PERR- > Interrupt: pin ? routed to IRQ 11 > Capabilities: [68] Power Management version 2 > Flags: PMEClk- DSI- D1- D2- AuxCurrent=3D0mA >PME(D0-,D1-,D2-,D3hot-,D3cold-) > Status: D0 PME-Enable- DSel=3D0 DScale=3D0 PME- > >0000:00:09.0 Class 0400: 109e:036e (rev 11) > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- >ParErr- Stepping- SERR- FastB2B- > Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=3Dmedium >TAbort- ><TAbort- <MAbort- >SERR- <PERR+ > Latency: 32 (4000ns min, 10000ns max) > Interrupt: pin A routed to IRQ 5 > Region 0: Memory at f7000000 (32-bit, prefetchable) > Capabilities: [44] Vital Product Data > Capabilities: [4c] Power Management version 2 > Flags: PMEClk- DSI+ D1- D2- AuxCurrent=3D0mA >PME(D0-,D1-,D2-,D3hot-,D3cold-) > Status: D0 PME-Enable- DSel=3D0 DScale=3D0 PME- > >0000:00:09.1 Class 0480: 109e:0878 (rev 11) > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- >ParErr- Stepping- SERR- FastB2B- > Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=3Dmedium >TAbort- ><TAbort- <MAbort- >SERR- <PERR+ > Latency: 32 (1000ns min, 63750ns max) > Interrupt: pin A routed to IRQ 5 > Region 0: Memory at f7001000 (32-bit, prefetchable) > Capabilities: [44] Vital Product Data > Capabilities: [4c] Power Management version 2 > Flags: PMEClk- DSI+ D1- D2- AuxCurrent=3D0mA >PME(D0-,D1-,D2-,D3hot-,D3cold-) > Status: D0 PME-Enable- DSel=3D0 DScale=3D0 PME- > >0000:00:0b.0 Class 0401: 1102:0002 (rev 08) > Subsystem: 1102:8064 > Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- >ParErr- Stepping- SERR- FastB2B- > Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=3Dmedium >TAbort- ><TAbort- <MAbort- >SERR- <PERR- > Latency: 32 (500ns min, 5000ns max) > Interrupt: pin A routed to IRQ 10 > Region 0: I/O ports at d000 > Capabilities: [dc] Power Management version 2 > Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=3D0mA >PME(D0-,D1-,D2-,D3hot-,D3cold-) > Status: D0 PME-Enable- DSel=3D0 DScale=3D0 PME- > >0000:00:0b.1 Class 0980: 1102:7002 (rev 08) > Subsystem: 1102:0020 > Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- >ParErr- Stepping- SERR- FastB2B- > Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=3Dmedium >TAbort- ><TAbort- <MAbort- >SERR- <PERR- > Latency: 32 > Region 0: I/O ports at d400 > Capabilities: [dc] Power Management version 2 > Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=3D0mA >PME(D0-,D1-,D2-,D3hot-,D3cold-) > Status: D0 PME-Enable- DSel=3D0 DScale=3D0 PME- > >0000:00:0d.0 Class 0180: 1095:3112 (rev 02) > Subsystem: 1095:3112 > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- >ParErr- Stepping- SERR- FastB2B- > Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=3Dmedium >TAbort- ><TAbort- <MAbort- >SERR- <PERR+ > Latency: 32, cache line size 08 > Interrupt: pin A routed to IRQ 11 > Region 0: I/O ports at d800 > Region 1: I/O ports at dc00 [size=3D4] > Region 2: I/O ports at e000 [size=3D8] > Region 3: I/O ports at e400 [size=3D4] > Region 4: I/O ports at e800 [size=3D16] > Region 5: Memory at f7002000 (32-bit, non-prefetchable) [size=3D512] > Capabilities: [60] Power Management version 2 > Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=3D0mA >PME(D0-,D1-,D2-,D3hot-,D3cold-) > Status: D0 PME-Enable- DSel=3D0 DScale=3D2 PME- > >0000:00:0f.0 Class 0200: 10ec:8139 (rev 10) > Subsystem: 10ec:8139 > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- >ParErr- Stepping- SERR- FastB2B- > Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=3Dmedium >TAbort- ><TAbort- <MAbort- >SERR- <PERR+ > Latency: 32 (8000ns min, 16000ns max) > Interrupt: pin A routed to IRQ 11 > Region 0: I/O ports at ec00 > Region 1: Memory at f7004000 (32-bit, non-prefetchable) [size=3D256] > Capabilities: [50] Power Management version 2 > Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=3D375mA >PME(D0-,D1+,D2+,D3hot+,D3cold+) > Status: D0 PME-Enable- DSel=3D0 DScale=3D0 PME- > >0000:01:05.0 Class 0300: 10de:0150 (rev a4) > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- >ParErr- Stepping- SERR- FastB2B- > Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=3Dmedium >TAbort- ><TAbort- <MAbort- >SERR- <PERR- > Latency: 248 (1250ns min, 250ns max) > Interrupt: pin A routed to IRQ 10 > Region 0: Memory at f4000000 (32-bit, non-prefetchable) > Region 1: Memory at e8000000 (32-bit, prefetchable) [size=3D128M] > Capabilities: [60] Power Management version 1 > Flags: PMEClk- DSI- D1- D2- AuxCurrent=3D0mA >PME(D0-,D1-,D2-,D3hot-,D3cold-) > Status: D0 PME-Enable- DSel=3D0 DScale=3D0 PME- > Capabilities: [44] AGP version 2.0 > Status: RQ=3D32 Iso- ArqSz=3D0 Cal=3D0 SBA+ ITACoh- = GART64- >HTrans- 64bit- FW+ AGP3- Rate=3Dx1,x2,x4 > Command: RQ=3D16 ArqSz=3D0 Cal=3D0 SBA+ AGP+ GART64- = 64bit- FW+ >Rate=3Dx4 > > >To me everything works (at least now). Can this patch be pushed into >2.6.12 and/or 2.6.11.4 fast? > |