From: Nicolas S. <Nic...@li...> - 2004-02-27 09:22:39
|
Hi, following problems: 1. echo -n "disk" > /sys/power/state => nothing happens 2. echo -n "mem" > /sys/power/state => the computer enters "suspend on ram" mode (the suspend light gets on, etc...) when I try to wake up the computer, it hangs (some noise indicating that the disks are woken up and then nothing but a blank screen, even starting from console). 3. It has certainly nothing to do with what I said before, but I cannot find a /proc/acpi/processor/CPU0/performance (I have all the other files you mention in your Documentation section). Here is an output of dmesg | grep acpi : BIOS-e820: 000000000bf70000 - 000000000bf7c000 (ACPI data) BIOS-e820: 000000000bf7c000 - 000000000bf80000 (ACPI NVS) ACPI: RSDP (v000 PTLTD ) @ 0x000f6c90 ACPI: RSDT (v001 PTLTD RSDT 0x06040000 LTP 0x00000000) @ 0x0bf75dcd ACPI: FADT (v001 ATI Salmon 0x06040000 ATI 0x000f4240) @ 0x0bf7bf64 ACPI: BOOT (v001 PTLTD $SBFTBL$ 0x06040000 LTP 0x00000001) @ 0x0bf7bfd8 ACPI: DSDT (v001 ATI MS2_1535 0x06040000 MSFT 0x0100000e) @ 0x00000000 Kernel command line: auto BOOT_IMAGE=Linux ro root=306 acpi=force ACPI: Subsystem revision 20040116 ACPI: IRQ9 SCI: Edge set to Level Trigger. ACPI: Interpreter enabled ACPI: Using PIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (00:00) ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGPB._PRT] ACPI: PCI Interrupt Link [LNK0] (IRQs 7 10) ACPI: PCI Interrupt Link [LNK1] (IRQs 7 *10) ACPI: PCI Interrupt Link [LNK2] (IRQs 7 *10) ACPI: PCI Interrupt Link [LNK3] (IRQs 7 *10) ACPI: PCI Interrupt Link [LNK4] (IRQs 7 11) ACPI: PCI Interrupt Link [LNK5] (IRQs 7 *11) ACPI: PCI Interrupt Link [LNK6] (IRQs 7 10) ACPI: PCI Interrupt Link [LNK7] (IRQs *5) ACPI: PCI Interrupt Link [LNK8] (IRQs 7 10) ACPI: Embedded Controller [EC0] (gpe 24) ACPI: PCI Interrupt Link [LNK7] enabled at IRQ 5 ACPI: PCI Interrupt Link [LNK6] enabled at IRQ 10 ACPI: PCI Interrupt Link [LNK5] enabled at IRQ 11 ACPI: PCI Interrupt Link [LNK2] enabled at IRQ 10 ACPI: PCI Interrupt Link [LNK3] enabled at IRQ 10 ACPI: PCI Interrupt Link [LNK4] enabled at IRQ 11 ACPI: No IRQ known for interrupt pin A of device 0000:00:10.0 ACPI: PCI Interrupt Link [LNK1] enabled at IRQ 10 ACPI: PCI Interrupt Link [LNK0] enabled at IRQ 10 PCI: Using ACPI for IRQ routing PCI: if you experience problems, try using option 'pci=noacpi' or even 'acpi=off' ACPI: (supports S0 S3 S4 S5) ACPI: No IRQ known for interrupt pin A of device 0000:00:10.0 ACPI: AC Adapter [ACAD] (on-line) ACPI: Processor [CPU0] (supports C1 C2 C3, 8 throttling states) ACPI: Battery Slot [BAT1] (battery present) ACPI: Power Button (FF) [PWRF] ACPI: Lid Switch [LID] ACPI: Thermal Zone [THRM] (33 C) and the output of cat /proc/interrupts: CPU0 0: 2204170 XT-PIC timer 1: 7729 XT-PIC i8042 2: 0 XT-PIC cascade 5: 0 XT-PIC ALi Audio Accelerator 8: 4 XT-PIC rtc 9: 330 XT-PIC acpi 10: 76313 XT-PIC uhci_hcd, uhci_hcd, eth0 11: 0 XT-PIC ehci_hcd 12: 23016 XT-PIC i8042 14: 51108 XT-PIC ide0 15: 1 XT-PIC ide1 NMI: 0 LOC: 0 ERR: 0 MIS: 0 Thanks in advance for your help. Nico. -- Nicolas SABOURET Laboratoire d'Informatique de Paris 6 (LIP6) 8, rue du Capitaine Scott, 75015 Paris, France http://www-oasis.lip6.fr/~sabouret |