Menu
▾
▴
[ACPI] Handler for [EmbeddedControl] returned AE_TIME in 2.6.1/20040116
|
From: Adam K. <ad...@bo...> - 2004-02-03 20:19:32
|
I'm using 2.6.1 with the latest ACPI patch (20040116). When I switch from
AC to battery or vice-versa, I get the following:
ACPI-0347: *** Error: Handler for [EmbeddedControl] returned AE_TIME
ACPI-1120: *** Error: Method execution failed [\_SB_.PCI0.ISA0.EC0_.SMWR] (Node d7f24f80), AE_TIME
ACPI-1120: *** Error: Method execution failed [\_SB_.PCI0.ISA0.BAT1.CHBP] (Node d7f238e0), AE_TIME
ACPI-1120: *** Error: Method execution failed [\_SB_.PCI0.ISA0.EC0_.SMSL] (Node d7f24f40), AE_TIME
ACPI-1120: *** Error: Method execution failed [\_SB_.PCI0.ISA0.EC0_._Q09] (Node d7f24ea0), AE_TIME
After that, ACPI no longer gives accurate information about the battery
status (e.g., it will say "discharging" and a fixed amount of battery
life left regardless of how much it has charged since the switch).
Sometimes I get this error on boot up.
I haven't found much discussion of this error in google or on this list.
In case it is useful, I've attached ACPI boot up messages below.[0] Also
the results of lspci -vv. [1]
I'm also using force=acpi because the BIOS on my system (HP OmniBook 500)
is too old for ACPI to be recognized automatically. HP has not released
any new BIOS for this system.
A couple of other problems perhaps worth mentioning: I can't resume from
suspend, either using the swsusp in 2.6.1 or the independent sourceforge
software suspend ("software suspend")--it hangs at "restoring pageset1."
Also, the kernel doesn't see the event of me pressing the sleep button,
although it does properly detected lid open and closed.
Any tips?
--
Adam Kessel
http://bostoncoop.net/adam
[0]
BIOS-e820: 0000000017ff0000 - 0000000017fffc00 (ACPI data)
BIOS-e820: 0000000017fffc00 - 0000000018000000 (ACPI NVS)
ACPI: RSDP (v000 HP-MCD ) @ 0x000f6c50
ACPI: RSDT (v001 HP-MCD FA RSDT 0x02700000 LTP 0x00000000) @ 0x17ff4e60
ACPI: FADT (v001 HP-MCD FA FACP 0x02700000 HP 0x01000000) @ 0x17ff4e8c
ACPI: BOOT (v001 PTLTD FABFTBL$ 0x02700000 LTP 0x00000001) @ 0x17fffbd8
ACPI: DSDT (v001 HP-MCD FA DSDT 0x02700000 MSFT 0x0100000d) @ 0x00000000
Kernel command line: root=/dev/hda2 ro acpi=force resume2=swap:/dev/hda3
ACPI: Subsystem revision 20040116
ACPI: IRQ9 SCI: Edge set to Level Trigger.
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Interrupt Link [LNKA] (IRQs *10)
ACPI: PCI Interrupt Link [LNKB] (IRQs *10)
ACPI: PCI Interrupt Link [LNKC] (IRQs *15)
ACPI: PCI Interrupt Link [LNKD] (IRQs *5)
ACPI: PCI Root Bridge [PCI0] (00:00)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: Embedded Controller [EC0] (gpe 0)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT]
ACPI: Power Resource [PFAN] (off)
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 5
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 10
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 15
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 10
PCI: Using ACPI for IRQ routing
PCI: if you experience problems, try using option 'pci=noacpi' or even 'acpi=off'
ACPI: AC Adapter [ACAD] (on-line)
ACPI: Battery Slot [BAT1] (battery absent)
ACPI: Battery Slot [BAT2] (battery absent)
ACPI: Battery Slot [BAT3] (battery absent)
ACPI: Power Button (FF) [PWRF]
ACPI: Lid Switch [LID]
ACPI: Sleep Button (CM) [SLP]
ACPI: Fan [FAN] (off)
ACPI: Processor [CPU0] (supports C1 C2 C3, 8 throttling states)
ACPI: Thermal Zone [THRM] (33 C)
ACPI: (supports S0 S1 S3 S4 S5)
[1]
00:00.0 Host bridge: Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX Host bridge (rev 03)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 64
Region 0: Memory at f8000000 (32-bit, prefetchable) [size=64M]
Capabilities: <available only to root>
00:01.0 PCI bridge: Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX AGP bridge (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 128
Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
I/O behind bridge: 00009000-00009fff
Memory behind bridge: f4100000-f5ffffff
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B+
00:07.0 ISA bridge: Intel Corp. 82371AB/EB/MB PIIX4 ISA (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:07.1 IDE interface: Intel Corp. 82371AB/EB/MB PIIX4 IDE (rev 01) (prog-if 80 [Master])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Region 4: I/O ports at 1000 [size=16]
00:07.2 USB Controller: Intel Corp. 82371AB/EB/MB PIIX4 USB (rev 01) (prog-if 00 [UHCI])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Interrupt: pin D routed to IRQ 5
Region 4: I/O ports at 1040 [size=32]
00:07.3 Bridge: Intel Corp. 82371AB/EB/MB PIIX4 ACPI (rev 03)
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin ? routed to IRQ 9
00:0a.0 CardBus bridge: Texas Instruments PCI1410 PC card Cardbus Controller (rev 01)
Subsystem: Hewlett-Packard Company: Unknown device 0011
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 168, Cache Line Size: 0x08 (32 bytes)
Interrupt: pin A routed to IRQ 10
Region 0: Memory at 18000000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=02, subordinate=05, sec-latency=176
Memory window 0: 18400000-187ff000 (prefetchable)
Memory window 1: 18800000-18bff000
I/O window 0: 00004000-000040ff
I/O window 1: 00004400-000044ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
00:0b.0 Ethernet controller: 3Com Corporation 3c556 Hurricane CardBus (rev 10)
Subsystem: 3Com Corporation: Unknown device 6256
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 80 (2500ns min, 1250ns max), Cache Line Size: 0x08 (32 bytes)
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at 1080 [size=128]
Region 1: Memory at f4000400 (32-bit, non-prefetchable) [size=128]
Region 2: Memory at f4000000 (32-bit, non-prefetchable) [size=128]
Expansion ROM at <unassigned> [disabled] [size=128K]
Capabilities: <available only to root>
00:0b.1 Communication controller: 3Com Corporation Mini PCI 56k Winmodem (rev 10)
Subsystem: 3Com Corporation: Unknown device 6158
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at 1400 [disabled] [size=256]
Region 1: Memory at f4000c00 (32-bit, non-prefetchable) [disabled] [size=256]
Region 2: Memory at f4000800 (32-bit, non-prefetchable) [disabled] [size=128]
Capabilities: <available only to root>
00:0d.0 Multimedia audio controller: ESS Technology ES1983S Maestro-3i PCI Audio Accelerator
Subsystem: Hewlett-Packard Company: Unknown device 0011
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (500ns min, 6000ns max)
Interrupt: pin A routed to IRQ 5
Region 0: I/O ports at 1800 [size=256]
Region 1: Memory at f4002000 (32-bit, non-prefetchable) [size=8K]
Capabilities: <available only to root>
00:11.0 IDE interface: CMD Technology Inc PCI0648 (rev 01) (prog-if 8f [Master SecP SecO PriP PriO])
Subsystem: Hewlett-Packard Company: Unknown device 0011
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (500ns min, 1000ns max)
Interrupt: pin A routed to IRQ 15
Region 0: I/O ports at 1128 [size=8]
Region 1: I/O ports at 1120 [size=4]
Region 2: I/O ports at 1148 [size=8]
Region 3: I/O ports at 1140 [size=4]
Region 4: I/O ports at 1010 [size=16]
Capabilities: <available only to root>
01:00.0 VGA compatible controller: ATI Technologies Inc Rage Mobility P/M AGP 2x (rev 64) (prog-if 00 [VGA])
Subsystem: Hewlett-Packard Company: Unknown device 0011
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 66 (2000ns min), Cache Line Size: 0x08 (32 bytes)
Interrupt: pin A routed to IRQ 10
Region 0: Memory at f5000000 (32-bit, non-prefetchable) [size=16M]
Region 1: I/O ports at 9000 [size=256]
Region 2: Memory at f4100000 (32-bit, non-prefetchable) [size=4K]
Expansion ROM at <unassigned> [disabled] [size=128K]
Capabilities: <available only to root>
|
