Learn how easy it is to sync an existing GitHub or Google Code repo to a SourceForge project! See Demo

Close

#691 Endless loop detection is too sensitive

None
wont-fix
nobody
None
5*
2014-01-03
2013-02-21
Torbjörn
No

I keep getting the "Texstudio has been paused due to a possible endless loop" warning each time Texstudio need to load a file and often also when jumping to a specific position in the code from the PDF viewer. I believe that it is due to my computer being slow and TexStudio too sensitive. Would it be possible to set the sensitivity? Could you also speed up the jumping to a specific position?

Related

Bugs: #691

Discussion

  • Which version do you have? I already made it a little bit less sensitive in 2.5.2 compared to 2.5.1.

    I think I set to around 40 second.

    How large are you files? There is already a check to temporarily disable the loop check, when a file that is larger than 30KB is loaded...

    How long does it take to jump to the source? It should be instantaneously.

    You can also disable it, by setting Crash%20Handler%20Type=5 in the ini file.

     
  • Torbjörn
    Torbjörn
    2013-02-23

    Thank you for your prompt replay. I have TeXstudio 2.5.2 (SVN 3661)
    Using Qt Version 4.8.1, compiled with Qt 4.8.1 R. I am writing my thesis
    and it consists of many files with sizes in the range 1KB to 479KB. The
    main file is 48KB. Jumping to the source takes between 10sec to a few
    minutes, when the infinite loop warning occurs and TexStudio freezes
    even though I choose to continue. The only solution then is to kill it
    and restart. I will try disabling it next week.

    Best wishes,
    Torbjörn

    On 2013-02-22 16:28, Benito van der Zander wrote:

    Which version do you have? I already made it a little bit less sensitive
    in 2.5.2 compared to 2.5.1.

    I think I set to around 40 second.

    How large are you files? There is already a check to temporarily disable
    the loop check, when a file that is larger than 30KB is loaded...

    How long does it take to jump to the source? It should be instantaneously.

    You can also disable it, by setting Crash%20Handler%20Type=5 in the ini
    file.


    [bugs:#691] http://sourceforge.net/p/texstudio/bugs/691/ Endless loop
    detection is too sensitive

    Status: open
    Created: Thu Feb 21, 2013 10:34 AM UTC by Torbjörn
    Last Updated: Thu Feb 21, 2013 10:34 AM UTC
    Owner: nobody

    I keep getting the "Texstudio has been paused due to a possible endless
    loop" warning each time Texstudio need to load a file and often also
    when jumping to a specific position in the code from the PDF viewer. I
    believe that it is due to my computer being slow and TexStudio too
    sensitive. Would it be possible to set the sensitivity? Could you also
    speed up the jumping to a specific position?


    Sent from sourceforge.net because you indicated interest in
    https://sourceforge.net/p/texstudio/bugs/691/

    To unsubscribe from further messages, please visit
    https://sourceforge.net/auth/prefs/

     

    Related

    Bugs: #691

  • Tim Hoffmann
    Tim Hoffmann
    2014-01-03

    • status: open --> wont-fix
    • Group: -->
     
  • Tim Hoffmann
    Tim Hoffmann
    2014-01-03

    closed because it seems to be related to a very slow computer. This should not happen for a normal user. Moreover, in the rare cases it might occur, it is possible to deactivate the crash handler.