What are the differences between MSI vs EXE? * VeraCrypt Setup 1.26.7.exe * VeraCrypt_Setup_x64_1.26.7.msi What are the differences between the Portable and the Extraction from "VeraCrypt Setup 1.26.7.exe"? I did a WinMerge comparison and they came out to be exactly the same extraction. * VeraCrypt Setup 1.26.7.exe * VeraCrypt Portable 1.26.7.exe
On my second attempt of doing a FULL DRIVE ENCRYPTION of the OS was successful. I am not sure if it is because one of the following? Installed (VeraCrypt_Setup_x64_1.26.7.msi) instead of (VeraCrypt Setup 1.26.7.exe). Did not select "YES" for "Encryption of Host Protected Area". Selected "No". Used a different SSD. It did not give the same issue as the above which I was hoping to replicate to understand why it failed.
Usually, I do a "system partition" encryption. Today, I decided to do a "system drive" encryption. It went through the pretest fine. However, when it was done encrypting, I rebooted and was not able to get pass the VeraCrypt password screen. It kept saying error out. So I popped that drive into another computer that has VeraCrypt. I was not able to log into the drive until I finally realized to use the "Mount Without Pre-Boot Authentication". It worked and mounted to a drive letter. I was then able...
Usually, I do a "system partition" encryption. Today, I decided to do a "system drive" encryption. It went through the pretest fine. However, when it was done encrypting, I rebooted and was not able to get pass the VeraCrypt password screen. It kept saying error out. So I popped that drive into another computer that has VeraCrypt. I was not able to log into the drive until I finally realized to use the "Mount Without Pre-Boot Authentication". It worked and mounted to a drive letter. I was then able...
I have three questions. Usually, I do a "system partition" encryption. Today, I decided to do a "system drive" encryption. It went through the pretest fine. However, when it was done encrypting, I rebooted and was not able to get pass the VeraCrypt password screen. It kept saying error out. So I popped that drive into another computer that has VeraCrypt. I was not able to log into the drive until I finally realized to use the "Mount Without Pre-Boot Authentication". It worked and mounted to a drive...
I have three questions. Usually, I do a "system partition" encryption. Today, I decided to do a "system drive" encryption. It went through the pretest fine. However, when it was done encrypting, I rebooted and was not able to get pass the VeraCrypt password screen. It kept saying error out. So I popped that drive into another computer that has VeraCrypt. I was not able to log into the drive until I finally realized to use the "Mount Without Pre-Boot Authentication". It worked and mounted to a drive...
I have three questions. Usually, I do a "system partition" encryption. Today, I decided to do a "system drive" encryption. It went through the pretest fine. However, when it was done encrypting, I rebooted and was not able to get pass the VeraCrypt password screen. It kept saying error out. So I popped that drive into another computer that has VeraCrypt. I was not able to log into the drive until I finally realized to use the "Mount Without Pre-Boot Authentication". It worked and mounted to a drive...
I have three questions. Usually, I do a "system partition" encryption. Today, I decided to do a "system drive" encryption. It went through the pretest fine. However, when it was done encrypting, I rebooted and was not able to get pass the VeraCrypt password screen. It kept saying error out. So I popped that drive into another computer that has VeraCrypt. I was not able to log into the drive until I finally realized to use the "Mount Without Pre-Boot Authentication". It worked and mounted to a drive...
So here is an update in case someone else runs into this situation. Luckily, I do have a backup of this drive but there is 10% of it that has not been backed up. Good practice for me is that I always do a comparison and take a screen print of the differences that are not backed up between the two drives. In this case, I knew exactly what I needed to recover. Fortunately, Recuva has been able to recovered 85% of the 10% (not backed up) which is about 200 GB. Mostly are old games. During those files...
I was able to get to the file structure using Recuva after 3 hours of scanning. Still clicking and not able to recover the files yet, except for one file (jpg).
I am able to mount the drive (with password, keyfiles, PIM, etc...). Once mounted and clicking on the mounted drive letter, I hear the hard drive clicking. The clicking only happens when I am trying to get to the mount letter. After a two minutes wait, I get a message of: The volume does not contain a recognized file system. Please make sure that all required file system drivers are loaded and that the volume is not corrupted. I am able to restore the backup header but still same issue. Have been...
I am able to mount the drive (with password, keyfiles, PIM, etc...). Once mounted and clicking on the mounted drive letter, I hear the hard drive clicking. The clicking only happens when I am trying to get to the mount letter. After a two minutes wait, I get a message of: The volume does not contain a recognized file system. Please make sure that all required file system drivers are loaded and that the volume is not corrupted. I am able to retore the backup header but still same issue. Have been...
I did a benchmark and SHA-512 is the fastest for a 512 bit. My questions are from a non-technical person, When does the hash kicks in? Is it during the password stage, the encryption/decryption of data or format of the drive? If I use SHA-512, is it less secure than the other two since it is faster? I am still trying to understand how hash and algorithm work together. For example: https://aboutssl.org/wp-content/uploads/2020/09/hashing-vs-encryption.svg?is-pending-load=1 Basically, does it take the...
I did a benchmark and SHA-512 is the fastest for a 512 bit. My questions are from a non-technical person, When does the hash kicks in? Is it during the password stage, the encryption/decryption of data or format of the drive? If I use SHA-512, is it less secure than the other two since it is faster? I am still trying to understand how hash and algorithm work together. For example: https://aboutssl.org/wp-content/uploads/2020/09/hashing-vs-encryption.svg?is-pending-load=1 Basically, does it take the...
I did a benchmark and SHA-512 is the fastest for a 512 bit. My questions are from a non-technical person, When does the hash kicks in? Is it during the password stage, the encryption/decryption of data or format of the drive? If I use SHA-512, is it less secure than the other two since it is faster? I am still trying to understand how hash and algorithm work together. For example: https://aboutssl.org/wp-content/uploads/2020/09/hashing-vs-encryption.svg?is-pending-load=1 Basically, does it take the...
I did a benchmark and SHA-512 is the fastest for a 512 bit. My questions are from a non-technical person, When does the hash kicks in? Is it during the password stage, the encryption/decryption of data or format of the drive? If I use SHA-512, is it less secure than the other two since it is faster? I am still trying to understand how hash and algorithm work together. For example: https://aboutssl.org/wp-content/uploads/2020/09/hashing-vs-encryption.svg?is-pending-load=1 Thanks
I did a benchmark and SHA-512 is the fastest for a 512 bit. My questions are from a non-technical person, When does the hash kicks in? Is it during the password stage, the encryption/decryption of data or format of the drive? If I use SHA-512, is it less secure than the other two since it is faster? Thanks
I did a benchmark and SHA-512 is the fastest for a 512 bit. My questions are from a non-technical person, When does the hash kicks in? Is it during the password stage, the encryption/decryption of data or format of the drive? If I use SHA-512, is it less secure than the other two since it is faster? Thanks
I did a benchmark and SHA-512 is the fastest for a 512 bit. My questions are from a non-technical person, When does the hash kicks in? Is it during the password stage, the encryption/decryption of data or format of the drive? If I use SHA-512, is it less secure than the other two since it is faster? Thanks
I did a benchmark and SHA-512 is the fastest for a 512 bit. My questions are from a non-technical person, When does the hash kicks in? Is it during the password stage, the encryption/decyption of data or format of the drive? If I use SHA-512, is it less secure than the other two since it is faster? Thanks
I did a benchmark and SHA-512 is the fastest for a 512 bit. My questions are from a non-technical person, When does the hash kicks in? Is it during the password stage, the encryption/decyption of data or format of the drive? If I use SHA-512, is it less secure than the other two since it is faster? Thanks
Thanks for your reply. Although i may not be able to save the os, I know how to extract the data which is the most important thing. I usually save a copy image of the os and it takes me only an hour to restore everything, including system encryption of the os. I was just hoping to save time and learn to resolve this "BCD" thing if I ever run into it again.
The latest one: Latest Stable Release - 1.25.9 (Saturday February 19, 2022)
"Create the boot Rescue Disk and decrypt the system encryption." What other functions does the Rescue Disk have? From your post, it decrypts and also restore the bootloader. Anything else? BTW... I have not used the rescue disk yet but I am able to still get to the VeraCrypt password screen and also able to enter my password. It is right after that I get the BCD message from my original post. I will use the Rescue Disk as you mentioned. Just thought I provide more details.
Thanks for the reply and will do what you have shared. BTW... I am always on the latest version of VeraCrypt. I believe this BCD issue was caused by something else not VeraCrypt. Since you have been on this forum for a long time, have you seen BCD issues often? I have only found one other thread: https://sourceforge.net/p/veracrypt/discussion/general/thread/85fa295961/
I have been using TrueCrypt/VeraCrypt for over 10 years. I have never had any issues with it until today. I was able to recover all of my data which is the good news. basically, I removed the ssd and attached to another computer using an usb enclosure. I was able to recover everything since I usually save to one master folder. I cannot get the OS to boot at this point and keep getting the message: "Recovery Your PC needs to be repaired The Boot Configuration Data file is missing some required information....
Hi, Issue 01: The XML issue has been resolved for the 64 bit version but there are no compiled version for 2.16.3 (32 bit version). Issue 02: When copied a 15 GB file, after it is done, still cannot access Winmerge as it gives the "thinking" icon. Works fine with the 32 bit version but still not the new 2.16.3 (64 bit version). I am on Windows 7 64 bit. Update: after 2nd attempt, 2.16.2 (32 bit version) takes only 1.5 minute while 2.16.3 (64 bit version) takes 5 minutes. 64 bit version finally give...
Hi, What does your previous email mean? Do I wait for you to post the compiled version of those fixes? Thanks Sent from Yahoo Mail on Android On Monday, April 22, 2019, 7:15:20 PM EDT, Takashi Sawanaka <sdottaka@users.sourceforge.net> wrote: status: open --> closed-fixed Comment: Fixed by commit https://bitbucket.org/winmerge/winmerge/commits/800113337ed44ff30643fdf32eac987c174051e8 and https://bitbucket.org/winmerge/winmerge/commits/6fe6776240d07c5f049f08d67ed3072c61ee378e Thank you for the report....
Possible Bugs in 2.16.2
That is very good to know which I was not aware. Thanks So could it be a service that recently I disabled or could it be the assignment of virtual memory which has slowed down the boot?
Hi it is not the password verification but right after that.
I am on Windows 7and when I boot up before doing a system encryption, it works fine. Once it passed the bios, it takes couple of a seconds before the Windows logo appears. However if I do a system encryption (with Veracrypt) on the system and afterward when I enter the password (Veracrypt), it takes about 30 seconds before the Windows logo appears. Once in Windows, everything seems to be fine. So the question is this delay a Veracrypt issue or a Window bootloader (mbr) issue? How would I fix thi...
I am on Windows 7and when Iboot up without system encryption it works fine. Once it passed the bios it takes couple of seconds before see Windows logo. However if I do a system encryption with Veracrypt on the system then afterward entering the password (Veracrypt), it takes about 30 seconds before I see the Windows logo. So the question is thisa Veracrypt issue or a Window boot loader (mbr) issue? How would I fix this?
I had System Favorite Volumes mounting issues prior to the release of version 1.21. For me, that has been resolved with the release of version 1.21. So thank you for fixing this. However, I just thought that I share one thing that I have noticed in case someone else is experiencing the same. This may/maynot be VeraCrypt related. Since the upgrade to version 1.21 on release day, my PC has frozen twice when moving a large file (in the gb size) between two drives with Serpent. Again, it may not be related...
I had System Favorite Volumes mounting issues prior to the release of version 1.21. For me, that has been resolved with the release of version 1.21. So thank you for fixing this. However, I just thought that I share one thing that I have noticed in case someone else is experiencing the same. This may/maynot be VeraCrypt related. Since the upgrade to version 1.21 on release day, my PC has frozen twice when moving a large file (in the gb size) between two drives with Serpent. Again, it may not be related...
I had System Favorite Volumes mounting issues prior to the release of version 1.21. For me, that has been resolved. So thank you for fixing this. However, I just thought that I share one thing that I have noticed in case someone else is experiencing the same. This may/maynot be VeraCrypt related. Since the upgrade to version 1.21 on release day, my PC has frozen twice when moving a large file (in the gb size) between two drives with Serpent. Again, it may not be related but my PC has not froze for...
Mounir, I have reverted back to 1.20 Beta. When I have time today/tomorrow, I will reimage and try 1.21 RC again. I did open Windows Event Viewer and look for events whose source is "VeraCryptSystemFavorites". I did not see any errors for 1.20 Beta. Here are the sequences: Starting System Favorites mounting process Loaded 1 favorites from the file Reading System Favorites XML file Mounting system favorite "\Device\Harddisk1\Partition1" Favorite "\Device\Harddisk1\Partition1" mounted successfully...
Nilsen, would you be able to check the registry key that Mournir provided above and see if there is a "/a favorites" in your value? I am wondering if version 1.21 need this for auto mount?
A little bit more digging on this. 1.20 Beta I have reimaged my OS back to a clean slate and installed VeraCrypt 1.20 Beta. I went through my normal routine and encrypted the System OS. After the encryption of the OS completed, I rebooted and mounted a drive and then added it to System Favorite. I rebooted and it worked. 1.21 RC Windows seems to take a bit longer to login after entering the Windows password. It seems VeraCrypt is looking for the System Favorite drives. Mournir, I noticed a difference...
Samething is happening to me as Nilsen. And this is on a clean install. Usually when VeraCrypt comes out with a new build, I reimage my OS back to a clean slate. After the reimage process, I install the new VerCrypt build and starts the system encryption process. I mount and then add System Favorite as normal. However, this time will not auto mount after a reboot. Nothing has changed in my process for the last 3 builds. I tried to downgrade back to 1.20 beta but it will not allow me unless I reimage...
will there be an official release soon?
I think there is a dismount feature after a certain amount of time with Force Di...
Andrea, I am not sure why the backup files became corrupted. As soon as I replaced...
You are correct about the keyfiles Andreas. I came back to provide an update but...
You are correct about the keyfiles Andreas. I came back to provide an update but...
I installed Veracrypt 1.19. File containers, system drive and all other drives are...
I installed Veracrypt 1.19. File containers, system drive and all other drives are...
Thank you for your reply Asator.
What exactly does Wipe Mode do while encrypting the System drive? I was a bit confuse...
Can I defrag a Veracrypt mounted volume? I remembered reading somewhere that it is...
Can I defrag a Veracrypt mounted volume? I remembered reading somewhere that it is...
My PC freezes within 10 minutes of reboot. If it does not freeze within that time...
Like always, thank you Enigma2Illusion.
If I mount a VeraCrypt file container or device, is it safe to window format or chkdsk...
OK, I figured it out. It has to do with this line in the configuration file: <config...
Yeah, strange. I just tried it on a different PC and it worked fine. Beep on mount...
Hi Enigma, I have been on 1.17. It was working fine before I reimaged my computer....
Strange! It still beeps and works fine on mount action but it has stopped beeping...
In reality there is really no need for cascade encryption right? It is really for...
In reality there is really no need for cascade encryption right? It is really for...
Enigma2 I am on windows ultimate 7 64 bit. I am in the process of moving to Windows...
Enigma, I think that I may not have been clear. Sorry, so let me rewalk you through....
I believe it is a Window error. When I encrypt an entire drive, I still create a...
"Encrypt and Format (destroys existing data)"
I ended up using System Favorites since it mounts the drive during Windows boot....
I ended up using System Favorites since it mounts the drive during Windows boot....
"In my opinion, it is best practice to make an external header backup for each encrypted...
Enigma, you mean backup header files right? "Make external header key backup" Also,...
Enigma, you mean backup header files right? "Make external header key backup"
Thanks for the information
For the hashing algorithim, you can set the default in the configuration.xml file...
This is scary since all of my drives have been encrypted. I have never lost a partition...
I just did mine again last night. Yes, this seems to be the normal. I got all encryption...
Thank you for your reply Enigma2. I noticed after the system drive has been encrypted;...
I will read those links Enigma. Can you share a quick overview of those 3 options?...
Thank you for your reply Enigma2. I noticed after the system drive is encrypted the...
Two questions: First, I have encrypted a drive. The usual norm is a drive letter...
I know VeraCrypt/TrueCrypt have implemented the ability of hidden volume for Plausible...
I know VeraCrypt/TrueCrypt have implemented the ability of hidden volume for Plausible...
I know VeraCrypt/TrueCrypt have implemented the ability of hidden volume for Plausible...
I know VeraCrypt/TrueCrypt have implemented the ability of hidden volume for Plausible...
I have encrypted a System drive successfully years ago. I don't remember the process....
I know VeraCrypt/TrueCrypt have implemented the ability of hidden volume for Plausible...
Mounir, I have tested 1.17-BETA21 and the these issues have been resolved. https://veracrypt.codeplex.com/workitem/354...
I have tested 1.17-BETA21 and the above issue has been resolved. Thank You
I have tested 1.17-BETA21 and the above issue has been resolved. Thank You
I have tested 1.17-BETA21 and the above issue has been resolved.
Awesome Mounir. Thank you for being so active on this!
I have not used but you may want to look into "TestCrypt.exe". I believe it recovers...
I noticed the implementation of a shortcut key for "P&IM" starting with version 1.17...
The random strength indicator is awesome! Good implementation.
Thank you Mounir! "So, we are left with an attack that runs on the current user session."...
Thank you Mournir! "So, we are left with an attack that runs on the current user...
"Can you reproduce it on your side?" If you are asking me Mounir, I will test it...
Is it ok that I also submit this as an issue? https://sourceforge.net/p/veracrypt/discussion/technical/thread/393905b7/...
Is it just me? When I select multiple keyfiles and click "OK", and then go back into...
Is it just me? When I select multiple keyfiles and click "OK", and then go back into...
The systray icon for version 1.17 Beta20 is so much better than the systray icon...
Mounir, I have extracted and tested 1.17-BETA20 for several hours. Issue is still...
Testing more and will update...