Activity for vmatthews
-
vmatthews posted a comment on discussion Help
I have not figured out how the GPIOChange functions.
-
Greetings; GCGU Version 1.0 21/9/2013 (I did grab the updates from a few weeks ago...
-
Was trying to use GPIO.2 Port as a interrupt change as listed in the Help's Interrupt...
-
Was trying to use GPIO.2 Port as a interrupt change as listed in the Interrupt listing....
-
The link> www.microchip.com/forums/m48207-print.aspx Stalled on loading page for...
-
The link> www.microchip.com/forums/m48207-print.aspx Did not work, just stuck on...
-
I did try a pull-up and a Pull-down, and no change there, but I will grab your LCH.h...
-
got it...
-
Ok, gotcha on the TmpString(1)="A" that worked great.. thanks vic
-
Like in NotePad or practically in an other text editors or spreadsheets/etc.
-
thank you -- THANK YOU.. I was believing I was somehow causing this issue. Bitter-sweet...
-
Recently D/Ld the new release of the Help file, and looking thru the different GC...
-
Sorry, since I've been all over the place on different issues, I don't know which...
-
This is crazy.... As you might remember I said I had re-built another breadboard...
-
posted.. thanks, vic
-
I am running 8mhz crystal with 22pf caps on a 16F877a... should I try slower 4mh...
-
posted.. thanks, vic p.s If you have a moment see my msg above your post concerning...
-
I am running 8mhz crystal with 22pf caps on a 16F877a... should I try slower 4mhz??...
-
UGH!!! Now that I ran the R/W direct to PIC, Now I'm getting garb aged characters...
-
Hey, I got it right !! I just came up to put that I found a work around, and you...
-
Thanks for the reply.. I did try your code the first time thru this: AlarmSign(NumTmp)...
-
using an LCD I tried to send this line.. Print "C=Range *=Cancel" Gives: Error in...
-
Yea, That's the section that will test the trigger(s) and associated LEDs for each...
-
Yea, That's the section that will test the trigger(s) and associated LEDs for each...
-
I am having more success using the hard wired R/W to PIC. and most the garbage characters...
-
SORRY about that.. the missing TrigLED1 & Reset_Sw. I was rushing up the code to...
-
Thanks; I will try tapping the R/W pin to a port and let you know. vic
-
I write this code in GC Version 1.0 21/9/2013 copy/paste this off the "about" screen....
-
here's the code..... But remember the LCD issue extends to most of my other projects...
-
-
here's the code.....
-
Here's the code...
-
;Chip Settings chip 16F877A,8 ;Defines (Constants) define LCD_IO 4 define LCD_RS...
-
I applied varies program delays from 50ms, 250 ms, 1 s, up to 5 secs.. then I wired...
-
At times in different projects, I get garaged characters when I fire-up the PIC with...
-
At times in different projects, I get garaged characters when I fire-up the PIC with...
-
At times in different projects, I get garaged characters when I fire-up the PIC with...
-
well I just open one of these pads and see no resistors, in the board or matrix pcb,...
-
WELL after moving the project to a different breadboard I used 1k resistors instead...
-
Thanks Chuck; I'll check that out.. I haven't found a solution yet, So I'll tear...
-
Thanks, I try that.. anyone else.. I'll repost the msg I left earlier that may have...
-
the attachment is 2 messages below.. Thanks guys for all your support to the users......
-
A good eye noticing the pull ups, that would be my bad, as I looked at the schematic...
-
the attachment is here
-
Who is up for a challenge? Actually, it will probably be easy for those who have...
-
Thank you for the quick reply. I was indeed using it and hoped that was my problem,...
-
Just curious, since I am playing around with a Keypad, I notice GC creates a line...
-
I have a BK200+ Development board with a PIC16F877a I acquired some years ago and...
1