Activity for Detlef Paschke
-
Detlef Paschke modified a comment on discussion Suggestions
Hello, Thank you for the tip, I switched to SDIO immediately. I just had to create a theme that I could actually see something on, otherwise everything else works without any problems and without having to deactivate IPv6. Best regards Detlef Paschke
-
Hello, Thank you for the tip, I switched to SDIO immediately. I just had to create a theme that I could actually see something on, otherwise everything else works without any problems and without having to deactivate IPv6. Best regards Detlef Paschke
-
But errors occur with every download. In the past, software was treated in such a way that known errors were fixed wherever possible. Today, it is only said what you have to do to get around the existing errors. Nobody puts any effort into their work anymore!
-
Hello, Incorporate into the Snappy Driver Installer program code that IPv6 is not used. It's stupid that you have to disable IPv6 in the system every time you want to use Snappy Driver Installer! Best regards Detlef Paschke
-
Exclude drivers for update
-
Crash under Windows 11
-
Hello, VirtualDub2 works fine for me under Windows 11 Pro. Best regards
-
Hi there, this problem still seems to exist. Megactl shows a faulty BBU although everything is OK. root@Proxmox:~# megasasctl a0 LSI 2108 MegaRAID encl:1 ldrv:1 batt:FAULT, low voltage a0d0 7446GiB RAID 5 1x5 optimal a0e252s0 1863GiB a0d0 online a0e252s1 1863GiB a0d0 online a0e252s2 1863GiB a0d0 online a0e252s3 1863GiB a0d0 online a0e252s4 1863GiB a0d0 online root@Proxmox:~# megaclisas-status -- Controller information -- -- ID | H/W Model | RAM | Temp | BBU | Firmware c0 | LSI 2108 MegaRAID | 512MB...
-
Hi, I wish a small update. Only * .vcf files are available for selection as Processing setting file. Under Win10 * .vcf is a contact file and Vdub (Vdub2 anyway) uses * .vdscript for a longer time as a processing setting file. A simple. In the file selection makes it possible to use this file as well. Best regards
-
Hello, I have never seen the surface of the native FFMpeg Xvid encoder, but the bit rate setting is fine with me. I do not change more with the Xvid or DivX codec also. Settings such as cropping or ratio I do with Virtualdub filters. Only if I encode videos that have a resolution greater than 720 * X, I have to change the profile from "Home" to "HD 720" on Xvid or DivX. If that is not necessary with the native FFMpeg Xvid encoder, then I only need to set the bitrate. Sometimes even 2-pass encoding,...
-
MPEG-4, Xvid, DivX with FFMpeg
-
Okay thanks anyway. Best regards
-
Multipass in one step
-
Hello, Thank you for the tip, but I already know this filter and can not use it. On the one hand, this filter is not suitable for Vdub x64, but far worse is that this filter does not apply formatting of saa files. As you can read on the page, this is also known since 2006. many Greetings Detlef Paschke
-
Hello, Unfortunately, it is usually the time available that is the problem. Possibly. it will work later. many Greetings Detlef Paschke
-
Subtitle filter / plugin for Vdub2 x86 and x64
-
Hello, I mentioned the Subtitle Filter 2.4 because I think it's very good and has been using it for years, does not need to be additionally installed and the source code is freely available. The only downside, he is not recognized by Vdub x64. many Greetings Detlef Paschke
-
Hello, I give here once a response in the event that someone in the future seeks a solution to this problem. I found a solution that works well for me. I've added the FccHandler AC-3 plugin to Vdub2 and let the ac3 files load from this filter instead of the caching input driver. This passes through the ac3 audio track directly and packs it into the created video file unchanged. But I also noticed that Vdub2 can work directly with multi-channel audio tracks and therefore I do not need to extract the...
-
Setting the view
-
Audio - 5.1 ac3 - Direct stream copy
-
Hello, I would love to try Redo Backup and Recovery, but I can not start it. The problem is this. I have only a 10 inch monitor on my small server for which I want to use Redo Backup, which has a max. Resolution of 800x600 has. If I now start Redo Backup, I give vga=315 in Bootpromt and so the resolution should be 800x600. That's her too. Until the GUI is started by Redo Backup. Then the resolution is switched to 1024x768 and my monitor can not handle this. I have tested this with a big monitor....
-
Hallo, wie mittlerweile bekannt, wieder auf deutsch. Ein Punkt ist mir in der /language/de.xml...
-
Klasse jetzt klappt es :-) Min/Max Werte oder Limit werden nicht angezeigt. Ist das...
-
ich habe freeipmi nun mit der Option --with-dont-check-for-root Kompiliert und damit...
-
also wenn ich mich als User wwwrun auf dem Server einlogge kann ich ipmi-sensors...
-
Hallo, ich bekomme folgende Meldung: /usr/sbin/ipmi-sensors /usr/sbin/ipmi-sensors:...
-
Hallo, ich versuche es mal auf deutsch. Ich möchte gern die Boardinfos über freeIPMI...
1
