Hey, How OpenLTE maintains the network connectivity with the UE, after the successful registration? I hope RRC Connection Reconfiguration Complete + Attach accept is the last message received from UE regarding the registration. Is there any specific messages that is exchanged between the eNodeB and UE to maintain that connectivity (i.e., keep the UE attached to the network) or just sending down the prescheduled broadcast information (MIB & SIB) is enough? Thanks & Regards Dominic
Hi Folks, Could someone please explain how the IP allocation works in LTE. I'm using a custom programmed Sysmocom USIM and successfully registered with OpenLTE network. But I'm unable to see any IP address assigned to the UE. Also the access to the internet is also not working. Am I missing anything or do I need to configure anything specifically for this purpose? Is the IP address and DNS address really sent to UE over the air? Thanks & Best Regards Dominic
Hi Guys When I run the command "sudo apt-get install pcscd pcsc-tools libccid libpcsclite-dev" I get the following error dominic@dominic:~$ sudo apt-get install pcscd pcsc-tools libccid libpcsclite-dev Reading package lists... Done Building dependency tree Reading state information... Done Package libccid is not available, but is referred to by another package. This may mean that the package is missing, has been obsoleted, or is only available from another source Package pcscd is not available, but...
Hi Guys When I run the command "sudo apt-get install pcscd pcsc-tools libccid libpcsclite-dev" I get the following error dominic@dominic:~$ sudo apt-get install pcscd pcsc-tools libccid libpcsclite-dev Reading package lists... Done Building dependency tree Reading state information... Done Package libccid is not available, but is referred to by another package. This may mean that the package is missing, has been obsoleted, or is only available from another source Package pcscd is not available, but...
Hi Erik I'm glad you were able to detect and connect to OpenLTE under Ubuntu 14.04 and B210. I'm using the same OS and hardware but have not succeeded with OpenLTE, even have not yet detected the network in my phone. Please help me. The following is the system setup I am using:- Processor: Intel Xeon(R)W-2145 CPU @ 3.70Ghz x 14 (It is a 8 core CPU) Memory : 32 GB OS : Ubuntu 14.04 LTS OS type : 64 bit USRP : NI USRP-2901 (the daughter board is same as B210) OpenLTE : openlte_v00-20-05 I straight...
Hi Dylanger I would like to know if you had any success in detecting the OpenLTE network in your smartphones. If yes, could you please share what all are the workarounds you did and please do share your system configuration (processor, ram and OS), openlte system parameters(from control terminal) and the antenna you have used. The hardware I'm using is NI USRP 2901 along with VERT900 antenna. The Sysem config is Intel i5, 16gb RAM, Ubuntu 14.04 LTS OS). Please share the details you have used. Kind...
Great David, So you can surely help me. Me too using the NI 2901 USRP, but for some reason the network is not getting detected. The device is detected and I'm able to run the code,everything seems fine except the network is not detected. Wiki was the reference and followed the steps given to instal, run, and configure openlte. Could you please share with me your system configuration , openlte system parameters and the antenna you used. This is so important for me. Thanks for your consideration D...
In case if I am going for completely blank SIM, what all are the parameters manadatorily needs to be written into the SIM to make it work with OpenLTE? Also, what all parameters are expected to come along with the SIM? How about ICCID, OPC and ADM1? Are these required to successfully run with OpenLTE or will just MCC, MNC, IMSI and Ki be enough?
In case if going for completely blank SIM, what all are the parameters manadatorily needs to be written into the SIM to make it work with OpenLTE? Also, what all parameters are expected to come along with the SIM? How about ICCID, OPC and ADM1? Are these required to successfully run with OpenLTE or will just MCC, MNC, IMSI and Ki be enough?
Hi Guys Webshop of Sysmocom is under certain maintenance and is likely to be remained closed for an indefinite period. Could someone please suggest an alternate source to purchase sysmousim or an alternate to sysmousim that could be used along with OpenLTE? Thanks
Hi Luge Me too have came across the same error. Have you succeeded in OpenLTE installation by any chance. If so, please share what you have done to achieve the same.
Hi Nagasai..Thanks alot for your response. But are you sure the instructions you have given works without fail? Because After building the source code, when I run the dream executable, I get the following error dream: error while loading shared libraries: libfaad_drm.so.2: cannot open shared object file: No such file or directory Could you please help me clear this issue. Best Regards Dominic
Hi Nagasai I followed the instructions given in the file (dream_install.sh) you provided, but still I get the similar error but different file it seems. "dream: error while loading shared libraries: libfaad.so.2: cannot open shared object file: No such file or directory" May I ask which location the error is refering to? Which is the location the said file is not present? Have you successfully built the source code in Ubuntu by following the instructions in the file you shared? Is there any other...
Hi Nagasai..Thanks alot for your response. But are you sure the instructions you have given works without fail? Because After building the source code, when I run the dream executable, I get the following error dream: error while loading shared libraries: libfaaddrm.so.2: cannot open shared object file: No such file or directory Could you please help me clear this issue. Best Regards Dominic
Hi All, Since the website "drm.sourceforge.net" is not working now, could someone please post the instructions to build the source code in Ubuntu. Any help or guidance is greatly appreciated. Thanks & Regards Dominic
Hi Julian, Please check the attached .bin files. The file named "MSC_DoMS.bin" is...
Hi Julian, Please check the attached .bin files. The file named "MSC_DoMS.bin" is...
Thanks a lot Julian. Let me try with the test MSC bitstream. I'll keep you in the...
Thanks a lot Julian. Let me try with the test MSC bitstream. I'll keep you in the...
Hi Julian, Thanks for your reply. But for now I need to know more about the displays...
Hi Julian, Thanks for your reply. But for now I need to know more about the displays...
Hi Julian, Thanks for your reply. But for now I need to know more about the displays...
Couldnt make work DREAM Transmitter. Please walk me through the procedures.
Yes Julian please give me some tips on that. I need to know how the multiplexing...
Hi all, I hope someone here could help me out of this Audio/Data services multplexing...