I am unable to get the belkin wifi dongle work on my ARM target board.I have described my complete steps.Any advise appreciated.
1.Is there any other known kernel patches that I can apply?
2.Is something wrong with my USB subsystem?
3.I have tried various cable length/with and without hub.Any other ideas?

Usb dongle:BelkinF5D7050 (ZD1211 based,verified with windows driver)

------
# uname -r
2.6.24.7-omap1-arm2

kernel configuration:
--------------------
 Networking -> Wireless->  Wireless extensions ,
 Generic IEEE 802.11 Networking Stack (mac80211),
 'simple' rate control algorithm ,Enable debugging output ,
  Software MAC add-on to the IEEE 802.11 networking stack
 
  Device Drivers->Networking Device Support->Wireless LAN->ZyDAS ZD1211/ZD1211B USB-wireless support
  Device Drivers->USB device support-> EHCI HCD (USB 2.0) support(disabled)
  Device Drivers->USB device support->USB Gadget Support->Gadget Zero (DEVELOPMENT)
  Device Drivers->Generic options->support for firmware upload

Toolchain:
arm Codesourcery 2007q3

lsusb
-----
bus 001 Device 003: ID 1267:0103 Logic3 / SpectraVideo plc
Bus 001 Device 002: ID 0451:2046 Texas Instruments, Inc. TUSB2046 Hub(I am behind the usb hub)
Bus 001 Device 001: ID 0000:0000

Dmesg
------

usb 1-1.1:1.0: uevent
zd1211rw 1-1.1:1.0: usb_probe_interface
zd1211rw 1-1.1:1.0: usb_probe_interface - got id
usb 1-1.1: print_id() 050d:705c v4810 full
usb 1-1.1: reset full speed USB device using musb_hdrc and address 5
zd1211rw 1-1.1:1.0: zd_netdev_alloc() netdev->flags 0x1002
zd1211rw 1-1.1:1.0: zd_netdev_alloc() netdev->features 0x00000000
zd1211rw 1-1.1:1.0: zd_chip_read_mac_addr_fw()
zd1211rw 1-1.1:1.0: probe() successful
zd1211rw 1-1.1:1.0: eth1
drivers/usb/core/inode.c: creating file '005'
usb 1-1.1: new device strings: Mfr=16, Product=32, SerialNumber=0
usb 1-1.1: Product: USB2.0 WLAN
usb 1-1.1: Manufacturer: Belkin
hub 1-1:1.0: state 7 ports 4 chg 0000 evt 0002
zd1211rw 1-1.1:1.0: iw_get_range()
zd1211rw 1-1.1:1.0: zd_usb_init_hw()
usb 1-1.1: request_fw_file() fw name zd1211/zd1211b_ub
usb 1-1.1: upload_firmware() firmware device id 0x4810 is equal to the actual device id
usb 1-1.1: request_fw_file() fw name zd1211/zd1211b_uphr
usb 1-1.1: upload_code() transfer size 4096
usb 1-1.1: upload_code() transfer size 1024
usb 1-1.1: upload_code() firmware confirm return value 0x01
zd1211rw 1-1.1:1.0: zd_usb_enable_int()
zd1211rw 1-1.1:1.0: zd_usb_enable_int() submit urb c7f0f120
zd1211rw 1-1.1:1.0: zd_chip_init_hw()
zd1211rw 1-1.1:1.0: dump_cr() CR_AFTER_PNP 0x00000000
zd1211rw 1-1.1:1.0: dump_cr() CR_GPI_EN 0x00000000
zd1211rw 1-1.1:1.0: zd_usb_ioread16v() read timed out
zd1211rw 1-1.1:1.0: zd_ioread32v_locked() error: zd_ioread16v_locked. Error number -110
zd1211rw 1-1.1:1.0: dump_cr() error reading CR_INTERRUPT. Error number -110
zd1211rw 1-1.1:1.0: zd_usb_disable_int() urb c7f0f120 killed
zd1211rw 1-1.1:1.0: zd_usb_init_hw() couldn't initialize mac. Error number -110
zd1211rw 1-1.1:1.0: iw_get_range()
zd1211rw 1-1.1:1.0: zd_usb_init_hw()
usb 1-1.1: request_fw_file() fw name zd1211/zd1211b_ub
usb 1-1.1: upload_firmware() firmware device id 0x4810 is equal to the actual device id
usb 1-1.1: request_fw_file() fw name zd1211/zd1211b_uphr
usb 1-1.1: upload_code() transfer size 4096
usb 1-1.1: upload_code() transfer size 1024
usb 1-1.1: upload_code() firmware confirm return value 0x01
# NetworkManager: <WARN>  nm_device_802_11_wireless_scan(): could not trigger wireless scan on device eth1: No such device


# ifconfig eth1 up
musb_h_tx_flush_fifo 124: Could not flush host TX fifo: csr: 020a
musb_h_ep0_irq 1090: no URB for end 0
usb 1-1.1: USB control request for firmware upload failed. Error number -110
usb 1-1.1: Could not upload firmware code uph. Error number -110
zd1211rw 1-1.1:1.0: couldn't load firmware. Error number -110
ifconfig: SIOCSIFFLAGS: Connection timed out
# musb_h_tx_flush_fifo 124: Could not flush host TX fifo: csr: 020a
musb_h_ep0_irq 1090: no URB for end 0
usb 1-1.1: USB control request for firmware upload failed. Error number -110
usb 1-1.1: Could not upload firmware code uph. Error number -110
zd1211rw 1-1.1:1.0: couldn't load firmware. Error number -110

Thanks
Sundar