Re: [Wirelessdriver-support] No EN1 or EN2

[vix <ne...@ka...>]

I've been successfully using the beta4 driver (with the patch applied) on my
500mhz tiBook since upgrading to Jaguar, but tonight I installed beta5.1 on
a different tiBook. The wireless card is an Engenius, internal antenna type.

Being in a hurry I didn't refer to any of the very helpful instructions I
remember having been posted to this list, but just went at it like this:

ran the uninstaller (there was an old version on it from 10.1x days)
ran the b5.1 installer
restarted with the Engenius card inserted and got a kernel panic on restart
ran the installer again, restarted without card inserted

pref pane was there but greyed out, no en2 (or any en) choice in list

Then I ran the three separate installer packages (ConfigApps, PrefPane,
Wireless Driver) one after another, popped in the card and voila, everything
worked. 

Don't know if this will be of any help, but in my case the third install was
the charm.

thanks as always for this very useful driver,
Vix


> Hi I too am having the no new network problem. My Cabletron Enterasys
> Roamabout card is seen by the PC card slot but no new entries in the
> Network preferences pane. 10.2.2, TiBook 400 384MB.
> 
> Any suggestions greatly appreciated
> 
> ### system info
> 
> ProductName:    Mac OS X
> ProductVersion: 10.2.2
> BuildVersion:   6F21
> Darwin Kens-TiBook.local. 6.2 Darwin Kernel Version 6.2: Tue Nov  5
> 22:00:03 PST 2002; root:xnu/xnu-344.12.2.obj~1/RELEASE_PPC  Power
> Macintosh powerpc
> ppc7400
> 
> ### wireless driver files installed
> 
> drwxr-xr-x    3 root  wheel   102 Nov  6 17:04 IOPCCardFamily.kext
> 2002-11-29 14:28:52.506 defaults[714]
> The domain/default pair of (loginwindow,
> AutoLaunchedApplicationDictionary) does not exist
> 
> ### wirelesscard info
> 
>    | |             "VersionOneInfo" = ("Cabletron","RoamAbout 802.11
> DS","Vers$
>    | |       +-o pccard156,2@0,0  <class IOPCCard16Device>
>    | |             "IOName" = "pccard156,2"
> 
> ### network info
> 
> lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384
>        inet6 ::1 prefixlen 128
>        inet6 fe80::1%lo0 prefixlen 64 scopeid 0x1
>        inet 127.0.0.1 netmask 0xff000000
> gif0: flags=8010<POINTOPOINT,MULTICAST> mtu 1280
> stf0: flags=0<> mtu 1280
> en1: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500
>        inet6 fe80::230:65ff:fe11:d6f1%en1 prefixlen 64 scopeid 0x4
>        inet 192.168.0.3 netmask 0xffffff00 broadcast 192.168.0.255
>        ether 00:30:65:11:d6:f1
>        media: autoselect status: active
>        supported media: autoselect
> en0: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500
>        inet6 fe80::230:65ff:fecc:4124%en0 prefixlen 64 scopeid 0x5
>        ether 00:30:65:cc:41:24
>        media: autoselect (none) status: inactive
>        supported media: none autoselect 10baseT/UTP <half-duplex>
> 10baseT/UTP <half-duplex,hw-loopback> 10baseT/UTP <full-duplex>
> 10baseT/UTP <full-duplex,hw-loopback> 100baseTX <half-duplex>
> 100baseTX <half-duplex,hw-loopback> 100baseTX <full-duplex> 100baseTX
> <full-duplex,hw-loopback>
> 
> ### wd command line tool status