Menu
▾
▴
[Wirelessdriver-support] tiBook, Orinoco Gold: almost, but not quite
|
From: Arun R. <ra...@pi...> - 2002-11-13 16:30:24
|
O Erudite Ones,
I've gotten this far:
1. I see en2 in the network panel, and have it set up exactly like my
Airport card but with a different IP address.
2. Lights on the card blink, and the signal strength meter shows a good
strong reading.
3. The Wireless Config pane apparently finds my network, because the
name shows up, and I didn't enter it.
Problems:
1. Can't get through to any host: tried turning Airport off, change IP
addresses, but no luck.
2. Signal strength meter registers a good reading even with the card
pulled out! Hmm ...
Here's the result of the troubleshooting script:
> [imola:~/WirelessConfig/Utilities] rao% ./Troubleshooting\ Info.command
>
> ### system info
>
> ProductName: Mac OS X
> ProductVersion: 10.2.2
> BuildVersion: 6F21
> Darwin imola.local. 6.2 Darwin Kernel Version 6.2: Tue Nov 5 22:00:03
> PST 2002; root:xnu/xnu-344.12.2.obj~1/RELEASE_PPC Power Macintosh
> powerpc
> ppc7450
>
> ### wireless driver files installed
>
> drwxr-xr-x 3 root wheel 102 Nov 12 23:37 WirelessDriver.kext
> drwxr-xr-x 3 root wheel 102 Nov 5 22:04 IOPCCardFamily.kext
> ls: /Library/PreferencePanes: No such file or directory
>
> ### wirelesscard info
>
> | | | "VersionOneInfo" = ("Lucent
> Technologies","WaveLAN/IEEE","V$
> | | | "VersionOneInfo" = ("Lucent
> Technologies","WaveLAN/IEEE")
> | | +-o pccard156,2@0,0 <class IOPCCard16Device>
> | | | "IOName" = "pccard156,2"
>
> ### network info
>
> lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384
> inet6 ::1 prefixlen 128
> inet6 fe80::1%lo0 prefixlen 64 scopeid 0x1
> inet 127.0.0.1 netmask 0xff000000
> gif0: flags=8010<POINTOPOINT,MULTICAST> mtu 1280
> stf0: flags=0<> mtu 1280
> en2: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500
> inet6 fe80::202:2dff:fe67:4126%en2 prefixlen 64 scopeid 0x4
> inet 192.168.21.156 netmask 0xfffffff8 broadcast 192.168.21.159
> ether 00:02:2d:67:41:26
> media: <unknown type> (DS11 <full-duplex>) status: active
> supported media: none manual autoselect DS1 <half-duplex> DS1
> <full-duplex> DS2 <half-duplex> DS2 <full-duplex> DS5 <half-duplex>
> DS5 <full-duplex> DS11 <half-duplex> DS11 <full-duplex>
> en0: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500
> inet6 fe80::203:93ff:fe86:3db2%en0 prefixlen 64 scopeid 0x5
> ether 00:03:93:86:3d:b2
> media: autoselect (none) status: inactive
> supported media: none autoselect 10baseT/UTP <half-duplex>
> 10baseT/UTP <half-duplex,hw-loopback> 10baseT/UTP <full-duplex>
> 10baseT/UTP <full-duplex,hw-loopback> 100baseTX <half-duplex>
> 100baseTX <half-duplex,hw-loopback> 100baseTX <full-duplex> 100baseTX
> <full-duplex,hw-loopback> 1000baseTX <full-duplex> 1000baseTX
> <full-duplex,hw-loopback> 1000baseTX <full-duplex,flow-control>
> 1000baseTX <full-duplex,flow-control,hw-loopback>
> en1: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500
> inet6 fe80::230:65ff:fe03:777b%en1 prefixlen 64 scopeid 0x6
> ether 00:30:65:03:77:7b
> media: autoselect (<unknown type>) status: inactive
> supported media: autoselect
>
> ### wd command line tool status
>
> 2002-11-13 06:58:29.209 WirelessConfig[2285] Iterations: 1
> Network Name: Our Home, successful: Y
> Status:
> Network: Our Home
> WEP Enabled:NO
> Signal Strength:84
> [imola:~/WirelessConfig/Utilities] rao%
>
and here's the result of netstat -r :
> [imola:~/WirelessConfig/Utilities] rao% netstat -r
> Routing tables
>
> Internet:
> Destination Gateway Flags Refs Use Netif
> Expire
> default 192.168.21.153 UGSc 10 6 en1
> localhost localhost UH 11 13786 lo0
> 169.254 link#6 UCS 0 0 en1
> 192.168.21.152/29 link#6 UCS 2 0 en1
> 192.168.21.153 0:6:2a:c8:38:54 UHLW 10 0 en1
> 549
> 192.168.21.154 localhost UHS 0 2 lo0
> 192.168.21.156 localhost UHS 0 2 lo0
> 192.168.21.159 link#6 UHLWb 4 34 en1
>
> Internet6:
> Destination Gateway Flags Netif Expire
> UH lo0
> fe80::%lo0 Uc lo0
> link#1 UHL lo0
> fe80::%en2 link#4 UC en2
> 0:2:2d:67:41:26 UHL lo0
> fe80::%en0 link#5 UC en0
> 0:3:93:86:3d:b2 UHL lo0
> fe80::%en1 link#6 UC en1
> 0:30:65:3:77:7b UHL lo0
> ff01:: U lo0
> ff02::%lo0 UC lo0
> ff02::%en2 link#4 UC en2
> ff02::%en0 link#5 UC en0
> ff02::%en1 link#6 UC en1
>
Any help is greatly appreciated ...
-Arun
|
