|
From: <Sim...@cs...> - 2010-04-23 23:21:22
|
(**) NVIDIA(0): Option "UseDisplayDevice" set to "none"; enabling NoScanout (**) NVIDIA(0): mode (--) NVIDIA(0): Not mapping the primary surface by default. (WW) NVIDIA(0): NoScanout is only supported on Tesla or Quadro hardware. (WW) NVIDIA(0): Disabling NoScanout. (II) NVIDIA(0): NVIDIA GPU Quadro NVS 420 (G98GL) at PCI:9:0:0 (GPU-0) (--) NVIDIA(0): Memory: 524288 kBytes (II) NVIDIA(0): GPU RAM Type: GDDR3 (--) NVIDIA(0): VideoBIOS: 62.98.68.00.06 (--) NVIDIA(0): Found 2 CRTCs on board (II) NVIDIA(0): Supported display device(s): DFP-0, DFP-1, DFP-2, DFP-3 (II) NVIDIA(0): Bus detected as PCI Express (II) NVIDIA(0): Detected PCI Express Link width: 4X (--) NVIDIA(0): Interlaced video modes are supported on this GPU (II) NVIDIA(0): DFP scaling is supported on this GPU (II) NVIDIA(0): SPS : 1 (II) NVIDIA(0): (II) NVIDIA(0): Mode timing constraints for : Quadro NVS 420 (II) NVIDIA(0): Maximum mode timing values : (II) NVIDIA(0): Horizontal Visible Width : 32767 (II) NVIDIA(0): Horizontal Blank Start : 32767 (II) NVIDIA(0): Horizontal Blank Width : 32767 (II) NVIDIA(0): Horizontal Sync Start : 32767 (II) NVIDIA(0): Horizontal Sync Width : 32767 (II) NVIDIA(0): Horizontal Total Width : 32767 (II) NVIDIA(0): Vertical Visible Height : 32767 (II) NVIDIA(0): Vertical Blank Start : 32767 (II) NVIDIA(0): Vertical Blank Width : 32767 (II) NVIDIA(0): Veritcal Sync Start : 32767 (II) NVIDIA(0): Vertical Sync Width : 32767 (II) NVIDIA(0): Vertical Total Height : 32767 (II) NVIDIA(0): (II) NVIDIA(0): Minimum mode timing values : (II) NVIDIA(0): Horizontal Total Width : 8 (II) NVIDIA(0): Vertical Total Height : 5 (II) NVIDIA(0): (II) NVIDIA(0): Mode timing alignment : (II) NVIDIA(0): Horizontal Visible Width : multiples of 1 (II) NVIDIA(0): Horizontal Blank Start : multiples of 1 (II) NVIDIA(0): Horizontal Blank Width : multiples of 1 (II) NVIDIA(0): Horizontal Sync Start : multiples of 1 (II) NVIDIA(0): Horizontal Sync Width : multiples of 1 (II) NVIDIA(0): Horizontal Total Width : multiples of 1 After that it goes onto the monitors (on DFP-2/3). Simon ________________________________________ From: Kumar, Shree [shr...@hp...] Sent: Friday, April 23, 2010 3:31 PM To: viz...@li... Subject: Re: [vizstack-users] Issue when changing between DVI and displayport on NVS420 No problem; you can test it at your convenience. I need one more piece of information to solve this problem. If you look in your Xorg log file, you will find a line which says "Supported display device(s)". Can you send me a few Lines around it ? Thanks -- Shree -----Original Message----- From: Sim...@cs... [mailto:Sim...@cs...] Sent: Friday, April 23, 2010 10:17 AM To: viz...@li... Subject: Re: [vizstack-users] Issue when changing between DVI and displayport on NVS420 I probably won't be able to test it until Tuesday Australian time (ANZAC day public holiday Monday), but I'll get onto it as soon as I can. Thanks for the quick response ;-) Simon > -----Original Message----- > From: Kumar, Shree [mailto:shr...@hp...] > Sent: Friday, 23 April 2010 2:25 PM > To: viz...@li... > Subject: Re: [vizstack-users] Issue when changing between DVI > and displayport on NVS420 > > Hi Simon, > > Thanks for the lspci dump and the info about the display > outputs. I'm glad this won't break any of my internal designs :-) > > Give me a day to remove the hardcoding. Then I'll let you > know so you can test. > > Thanks > -- Shree ------------------------------------------------------------------------------ _______________________________________________ vizstack-users mailing list viz...@li... https://lists.sourceforge.net/lists/listinfo/vizstack-users ------------------------------------------------------------------------------ _______________________________________________ vizstack-users mailing list viz...@li... https://lists.sourceforge.net/lists/listinfo/vizstack-users |