A new failure has been detected on builder valgrind-debian-armhf while building valgrind.
Full details are available at:
https://builder.sourceware.org/buildbot/#/builders/30/builds/1591
Build state: failed test (failure)
Revision: b640fa64b899af41038c24d2da5989dd6eaa9015
Worker: debian-armhf
Build Reason: (unknown)
Blamelist: Florian Krohm <fl...@ei...>
Steps:
- 0: worker_preparation ( success )
- 1: git checkout ( success )
Logs:
- stdio: https://builder.sourceware.org/buildbot/#/builders/30/builds/1591/steps/1/logs/stdio
- 2: autogen ( success )
Logs:
- stdio: https://builder.sourceware.org/buildbot/#/builders/30/builds/1591/steps/2/logs/stdio
- 3: configure ( success )
Logs:
- stdio: https://builder.sourceware.org/buildbot/#/builders/30/builds/1591/steps/3/logs/stdio
- config.log: https://builder.sourceware.org/buildbot/#/builders/30/builds/1591/steps/3/logs/config_log
- 4: make ( warnings )
Logs:
- stdio: https://builder.sourceware.org/buildbot/#/builders/30/builds/1591/steps/4/logs/stdio
- warnings (125): https://builder.sourceware.org/buildbot/#/builders/30/builds/1591/steps/4/logs/warnings__125_
- 5: make check ( success )
Logs:
- stdio: https://builder.sourceware.org/buildbot/#/builders/30/builds/1591/steps/5/logs/stdio
- 6: make regtest ( failure )
Logs:
- stdio: https://builder.sourceware.org/buildbot/#/builders/30/builds/1591/steps/6/logs/stdio
- 7: make ltpchecks ( warnings )
Logs:
- stdio: https://builder.sourceware.org/buildbot/#/builders/30/builds/1591/steps/7/logs/stdio
- warnings (677): https://builder.sourceware.org/buildbot/#/builders/30/builds/1591/steps/7/logs/warnings__677_
- 8: prep ( success )
Logs:
- stdio: https://builder.sourceware.org/buildbot/#/builders/30/builds/1591/steps/8/logs/stdio
- 9: build bunsen.cpio.gz ( success )
Logs:
- stdio: https://builder.sourceware.org/buildbot/#/builders/30/builds/1591/steps/9/logs/stdio
- 10: fetch bunsen.cpio.gz ( success )
Logs:
- stdio: https://builder.sourceware.org/buildbot/#/builders/30/builds/1591/steps/10/logs/stdio
- 11: unpack bunsen.cpio.gz ( success )
Logs:
- stdio: https://builder.sourceware.org/buildbot/#/builders/30/builds/1591/steps/11/logs/stdio
- 12: pass .bunsen.source.* ( success )
Logs:
- stdio: https://builder.sourceware.org/buildbot/#/builders/30/builds/1591/steps/12/logs/stdio
- 13: upload to bunsen ( success )
Logs:
- stdio: https://builder.sourceware.org/buildbot/#/builders/30/builds/1591/steps/13/logs/stdio
- 14: clean up ( success )
Logs:
- stdio: https://builder.sourceware.org/buildbot/#/builders/30/builds/1591/steps/14/logs/stdio
- 15: remove ltpchecks results dir ( success )
Logs:
- stdio: https://builder.sourceware.org/buildbot/#/builders/30/builds/1591/steps/15/logs/stdio
- 16: make distclean ( success )
Logs:
- stdio: https://builder.sourceware.org/buildbot/#/builders/30/builds/1591/steps/16/logs/stdio
|
