I updated the WNR3500L to Beta11 and updated the ftdi_sio.ko aswell from the extras.
Symtom was that it couldn't talk to the Cardreader and tries to reset it over and over again.
Did you verify (with lsmod) that the module is loaded? What messages - if any - are you getting in the system log?
Also, did it work for you in beta10?
If you would like to refer to this comment somewhere else in this project, copy and paste the following link:
I verified that it was loaded but I have misplaced the log file I took.
It was something like this
"drivers/usb/serial/ftdi_sio.c: ftdi_tiocmget Could not get modem status of device"
"/ftdi_sio.c: update_mctrl Error from MODEM_CTRL urb: DTR LOW, RTS LOW"
I jumped from Beta7 to beta 11 and are using the ftdi_sio from Beta7 with success.
Beta7 worked quite nice but I upgraded cause there was better support in Beta11
I could reinstall the nonworking ftdi_sio and get you a loggfile if you like. To make it easier to track down.
If you would like to refer to this comment somewhere else in this project, copy and paste the following link:
Ok, so the old version of ftdi_sio from beta07 still works for your device with beta11, and the only problem is when you're trying to use new ftdi_sio.ko?
What device do you use it with? And yes - if you can get me a log from non-working version that may help. Thank you.
If you would like to refer to this comment somewhere else in this project, copy and paste the following link:
Me and 1 other has encountered this problem.
It looks like it does a reinit of some kind and after that it says something about the wrong CAID or something.
Dont have any log info regarding this at this moment. But will look for it and post it asap.
Thanks for a great work!
If you would like to refer to this comment somewhere else in this project, copy and paste the following link:
Please retest with beta 14 when you get a chance - it might be fixed. Please note that in beta 14 ftdi_sio is built-in into the firmware, there's no need to use separate module.
If you would like to refer to this comment somewhere else in this project, copy and paste the following link:
a user at a forum a frequently visit has tried Beta14:
I've tested a bit fast and indeed it seems that most of what you need now to be built in the Tomato firmware.
One need only instance typing "insmod usbserial" and "insmod ftdi_sio" as installed in Phoenix reader / dev/ttyUSB0
The problem is that there is so much integrated that there is no room left in the / jffs - the ability to add and newcs.openwrt.mips newcs.xml but none of the other files will fit.
The other files I mention are libcrypto.so.0.9.8 such as we have "cheated" so that it works.
Nowadays there are built-in libcrypto Tomato (/ usr / lib / libcrypto.so) but because newcs looks specifically for libcrypto.so.0.9.8 just so you get the error message:
--- Quote ---
/ Newcs: Can not load library 'libcrypto.so.0.9.8'
--- End quote ---
.. When you try to start.
Quite irritable because it should work just fine with the version contained in Tomato.
One can safely restart newcs with files on a usbmemory, but then you have to connect a USB hub to have the reader plugged in simultaneously.
If anyone knows how to free space on the router - or newcs starts with any command that reads "right" libcrypto - you are welcome to enlighten me.
If you would like to refer to this comment somewhere else in this project, copy and paste the following link:
I've been running Tomato on NewCS 1.67 beta 14 (beta 15 is released, but there seems to be so much change) through Atomized tips above.
I made a symlink to libcrypto.so.0.9.8 linked to / usr / lib / libcrypto.so in the local lib folder under jffs and started with. / Start (the same "cheat-off" we have done before) - which joined the started.
But it seems to be a problem with usbserial and / or ftdi_sio, because you can not read the card while it is mounted.
If you would like to refer to this comment somewhere else in this project, copy and paste the following link:
I didn't understand your last 2 comments. You're mixing subjects, talking about libcrypto, jffs etc...
This issue is for ftdi_sio driver. If there's still a problem with it in the latest betas, please explain exactly what the problem is in plain English. Please note that I don't have the Phoenix cardreader, and not familiar with this hardware - you need to provide as many details as you can without dragging in any unnecessary stuff.
If you would like to refer to this comment somewhere else in this project, copy and paste the following link:
Did you verify (with lsmod) that the module is loaded? What messages - if any - are you getting in the system log?
Also, did it work for you in beta10?
I verified that it was loaded but I have misplaced the log file I took.
It was something like this
"drivers/usb/serial/ftdi_sio.c: ftdi_tiocmget Could not get modem status of device"
"/ftdi_sio.c: update_mctrl Error from MODEM_CTRL urb: DTR LOW, RTS LOW"
I jumped from Beta7 to beta 11 and are using the ftdi_sio from Beta7 with success.
Beta7 worked quite nice but I upgraded cause there was better support in Beta11
I could reinstall the nonworking ftdi_sio and get you a loggfile if you like. To make it easier to track down.
Ok, so the old version of ftdi_sio from beta07 still works for your device with beta11, and the only problem is when you're trying to use new ftdi_sio.ko?
What device do you use it with? And yes - if you can get me a log from non-working version that may help. Thank you.
Here comes tons of logs :-P
No errors after starting the cardreader. But after a few hours:
[ 17:35:43 ] [ Loader ] Reader type 2 on node /dev/ttyUSB1
[ 17:35:43 ] [ Phoenix ] Opening device /dev/ttyUSB1
[ 17:35:43 ] [ Phoenix ] Setting Parity to: ODD
[ 17:35:43 ] [ Phoenix ] Setting 2 Stop bits on node /dev/ttyUSB1
[ 17:35:43 ] [ Phoenix ] Setting Baud to standard 9600
[ 17:35:44 ] [ Phoenix ] Normal RESET on node /dev/ttyUSB1
[ 17:35:45 ] [ Loader ] Reset failed ...
[ 17:35:45 ] [ Loader ] Reader type 2 on node /dev/ttyUSB0
[ 17:35:45 ] [ Phoenix ] Opening device /dev/ttyUSB0
[ 17:35:45 ] [ Phoenix ] Could not get device /dev/ttyUSB0
[ 17:35:45 ] [ Loader ] Reset failed ...
[ 17:35:45 ] [ Loader ] Reader type 2 on node /dev/ttyUSB1
[ 17:35:45 ] [ Phoenix ] Opening device /dev/ttyUSB1
[ 17:35:45 ] [ Phoenix ] Setting Parity to: ODD
[ 17:35:45 ] [ Phoenix ] Setting 2 Stop bits on node /dev/ttyUSB1
[ 17:35:45 ] [ Phoenix ] Setting Baud to standard 9600
[ 17:35:46 ] [ Phoenix ] Normal RESET on node /dev/ttyUSB1
[ 17:35:47 ] [ Loader ] Reset failed ...
LSMOD:
Module Size Used by Tainted: P
ftdi_sio 36048 1
usbserial 33472 3 ftdi_sio
nls_cp852 4512 1
ohci_hcd 19856 0
ehci_hcd 36112 0
vfat 11744 1
fat 56176 1 vfat
ext2 67712 0
ext3 136608 0
jbd 61984 1 ext3
mbcache 7312 2 ext2,ext3
usb_storage 48320 1
sd_mod 27088 2
scsi_wait_scan 960 0
scsi_mod 104672 3 usb_storage,sd_mod,scsi_wait_scan
usbcore 138480 6 ftdi_sio,usbserial,ohci_hcd,ehci_hcd,usb_storage
jffs2 121472 1
zlib_inflate 15040 1 jffs2
zlib_deflate 21552 1 jffs2
nf_nat_ftp 2816 0
nf_conntrack_ftp 8384 1 nf_nat_ftp
nf_nat_sip 4416 0
nf_conntrack_sip 9024 1 nf_nat_sip
nf_nat_h323 7360 0
nf_conntrack_h323 49600 1 nf_nat_h323
nf_nat_rtsp 5520 0
nf_conntrack_rtsp 7520 1 nf_nat_rtsp
tomato_ct 2304 0
wl 2051584 0
igs 17904 1 wl
emf 22656 2 wl,igs
et 58848 0
AFTER LOGIN;
Tomato v1.27.9045 MIPSR2-beta11 K26 USB Ext
BusyBox v1.16.1 (2010-04-26 14:21:42 EDT) built-in shell (ash)
Enter 'help' for a list of built-in commands.
root@tomato:/tmp/home/root# dmesg
Linux version 2.6.22.19 (root@tomato) (gcc version 4.2.4) #1 Mon Apr 26 14:49:08 EDT 2010
CPU revision is: 00019740
Found a 8MB ST compatible serial flash
Determined physical RAM map:
memory: 04000000 @ 00000000 (usable)
On node 0 totalpages: 16384
Normal zone: 128 pages used for memmap
Normal zone: 0 pages reserved
Normal zone: 16256 pages, LIFO batch:3
Built 1 zonelists. Total pages: 16256
Kernel command line: root=/dev/mtdblock2 noinitrd console=ttyS0,115200
Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, linesize 32 bytes.
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
PID hash table entries: 256 (order: 8, 1024 bytes)
CPU: BCM4716 rev 1 pkg 10 at 453 MHz
Using 226.500 MHz high precision timer.
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 62060k/65536k available (2072k kernel code, 3412k reserved, 433k data, 108k init, 0k highmem)
SLUB: Genslabs=6, HWalign=32, Order=0-1, MinObjects=4, CPUs=1, Nodes=1
Calibrating delay loop... 225.28 BogoMIPS (lpj=112640)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
PCI: Using membase 8000000
PCI: Disabled
PCI: Fixing up bus 0
PCI: Fixing up bus 1
Time: MIPS clocksource has been installed.
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
squashfs: version 3.0 (2006/03/15) Phillip Lougher
io scheduler noop registered (default)
HDLC line discipline: version $Revision: 4.8 $, maxframe=4096
N_HDLC line discipline registered.
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x0 (irq = 8) is a 16550A
PPP generic driver version 2.4.2
PPP BSD Compression module registered
NET: Registered protocol family 24
PPPoL2TP kernel driver, V0.17
PPTP driver version 0.8.4
pflash: found no supported devices
Creating 6 MTD partitions on "sflash":
0x00000000-0x00040000 : "pmon"
0x00040000-0x007e0000 : "linux"
0x00119000-0x00550000 : "rootfs"
0x00550000-0x007e0000 : "jffs2"
0x007f0000-0x00800000 : "nvram"
0x007e0000-0x007f0000 : "board_data"
u32 classifier
Performance counters on
OLD policer on
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (512 buckets, 4096 max)
ip_tables: (C) 2000-2006 Netfilter Core Team
NET: Registered protocol family 1
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 108k freed
Warning: unable to open an initial console.
et: module license 'unspecified' taints kernel.
PCI: Setting latency timer of device 0000:00:02.0 to 64
eth0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 5.10.56.46
PCI: Setting latency timer of device 0000:00:01.0 to 64
eth1: Broadcom BCM4329 802.11 Wireless Controller 5.10.56.46
net/ipv4/netfilter/tomato_ct.c [Apr 26 2010 14:54:29]
Algorithmics/MIPS FPU Emulator v1.5
nf_conntrack_rtsp v0.6.21 loading
nf_nat_rtsp v0.6.21 loading
JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
SCSI subsystem initialized
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
PCI: Setting latency timer of device 0000:00:04.1 to 64
ehci_hcd 0000:00:04.1: EHCI Host Controller
ehci_hcd 0000:00:04.1: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:04.1: irq 5, io mem 0x18004000
ehci_hcd 0000:00:04.1: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
PCI: Setting latency timer of device 0000:00:04.0 to 64
ohci_hcd 0000:00:04.0: OHCI Host Controller
ohci_hcd 0000:00:04.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:04.0: irq 5, io mem 0x18009000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
usb 1-1: new high speed USB device using ehci_hcd and address 2
usb 1-1: configuration #1 chosen from 1 choice
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 4 ports detected
vlan1: add 01:00:5e:00:00:01 mcast address to master interface
vlan1: dev_set_promiscuity(master, 1)
device eth0 entered promiscuous mode
device vlan1 entered promiscuous mode
device eth1 entered promiscuous mode
br0: port 2(eth1) entering learning state
br0: port 1(vlan1) entering learning state
br0: topology change detected, propagating
br0: port 2(eth1) entering forwarding state
br0: topology change detected, propagating
br0: port 1(vlan1) entering forwarding state
vlan2: Setting MAC address to 00 26 f2 cd c2 0b.
vlan2: add 01:00:5e:00:00:01 mcast address to master interface
usb 1-1.1: new full speed USB device using ehci_hcd and address 3
root@tomato:/tmp/home/root#
After Trying to start Newcs again:
[ 17:41:08 ] [ Loader ] Reader type 2 on node /dev/ttyUSB0
[ 17:41:08 ] [ Phoenix ] Opening device /dev/ttyUSB0
[ 17:41:08 ] [ Phoenix ] Could not get device /dev/ttyUSB0
[ 17:41:08 ] [ Loader ] Reset failed ...
[ 17:41:08 ] [ Loader ] Reader type 2 on node /dev/ttyUSB1
[ 17:41:08 ] [ Phoenix ] Opening device /dev/ttyUSB1
[ 17:41:08 ] [ Phoenix ] Could not get device /dev/ttyUSB1
[ 17:41:08 ] [ Loader ] Reset failed ...
[ 17:41:08 ] [ Loader ] Reader type 2 on node /dev/ttyUSB0
[ 17:41:08 ] [ Phoenix ] Opening device /dev/ttyUSB0
[ 17:41:08 ] [ Phoenix ] Could not get device /dev/ttyUSB0
[ 17:41:08 ] [ Loader ] Reset failed ...
[ 17:41:08 ] [ Loader ] Reader type 2 on node /dev/ttyUSB1
[ 17:41:08 ] [ Phoenix ] Opening device /dev/ttyUSB1
[ 17:41:08 ] [ Phoenix ] Could not get device /dev/ttyUSB1
[ 17:41:08 ] [ Loader ] Reset failed ...
The only thing to do is to reverse to Beta7 of ftdi_sio.ko and I can start newcs again.
I'm using a NETGEAR WNR3500L
a Crystal I-Rock USB Hub
2 Smargo Cardreaders.
Newcs 1.67 RC1
Me and 1 other has encountered this problem.
It looks like it does a reinit of some kind and after that it says something about the wrong CAID or something.
Dont have any log info regarding this at this moment. But will look for it and post it asap.
Thanks for a great work!
Please retest with beta 14 when you get a chance - it might be fixed. Please note that in beta 14 ftdi_sio is built-in into the firmware, there's no need to use separate module.
I will do so asap.
Where can I find the release notes for Beta14?
a user at a forum a frequently visit has tried Beta14:
I've tested a bit fast and indeed it seems that most of what you need now to be built in the Tomato firmware.
One need only instance typing "insmod usbserial" and "insmod ftdi_sio" as installed in Phoenix reader / dev/ttyUSB0
The problem is that there is so much integrated that there is no room left in the / jffs - the ability to add and newcs.openwrt.mips newcs.xml but none of the other files will fit.
The other files I mention are libcrypto.so.0.9.8 such as we have "cheated" so that it works.
Nowadays there are built-in libcrypto Tomato (/ usr / lib / libcrypto.so) but because newcs looks specifically for libcrypto.so.0.9.8 just so you get the error message:
--- Quote ---
/ Newcs: Can not load library 'libcrypto.so.0.9.8'
--- End quote ---
.. When you try to start.
Quite irritable because it should work just fine with the version contained in Tomato.
One can safely restart newcs with files on a usbmemory, but then you have to connect a USB hub to have the reader plugged in simultaneously.
If anyone knows how to free space on the router - or newcs starts with any command that reads "right" libcrypto - you are welcome to enlighten me.
Thought only update that I continue to do tests.
I've been running Tomato on NewCS 1.67 beta 14 (beta 15 is released, but there seems to be so much change) through Atomized tips above.
I made a symlink to libcrypto.so.0.9.8 linked to / usr / lib / libcrypto.so in the local lib folder under jffs and started with. / Start (the same "cheat-off" we have done before) - which joined the started.
But it seems to be a problem with usbserial and / or ftdi_sio, because you can not read the card while it is mounted.
I didn't understand your last 2 comments. You're mixing subjects, talking about libcrypto, jffs etc...
This issue is for ftdi_sio driver. If there's still a problem with it in the latest betas, please explain exactly what the problem is in plain English. Please note that I don't have the Phoenix cardreader, and not familiar with this hardware - you need to provide as many details as you can without dragging in any unnecessary stuff.
Hi again!
Sorry for mixing things up.
I added the Cardreader and a USB memory thru a USBHUBB.
I cant get the driver for USB to work see the following Log:
Using Beta16
root@tomato:/tmp/mnt/CARD/Beta16/newcs/bin# dmesg
Linux version 2.6.22.19 (root@tomato) (gcc version 4.2.4) #1 Fri Jun 11 00:29:28 EDT 2010
CPU revision is: 00019740
Found a 8MB ST compatible serial flash
Determined physical RAM map:
memory: 04000000 @ 00000000 (usable)
On node 0 totalpages: 16384
Normal zone: 128 pages used for memmap
Normal zone: 0 pages reserved
Normal zone: 16256 pages, LIFO batch:3
Built 1 zonelists. Total pages: 16256
Kernel command line: root=/dev/mtdblock2 noinitrd console=ttyS0,115200
Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, linesize 32 bytes.
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
PID hash table entries: 256 (order: 8, 1024 bytes)
CPU: BCM4716 rev 1 pkg 10 at 453 MHz
Using 226.500 MHz high precision timer.
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 62060k/65536k available (2063k kernel code, 3412k reserved, 442k data, 108k init, 0k highmem)
SLUB: Genslabs=6, HWalign=32, Order=0-1, MinObjects=4, CPUs=1, Nodes=1
Calibrating delay loop... 225.28 BogoMIPS (lpj=112640)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
PCI: Using membase 8000000
PCI: Disabled
PCI: Fixing up bus 0
PCI: Fixing up bus 1
Time: MIPS clocksource has been installed.
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
squashfs: version 3.0 (2006/03/15) Phillip Lougher
io scheduler noop registered (default)
HDLC line discipline: version $Revision: 4.8 $, maxframe=4096
N_HDLC line discipline registered.
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x0 (irq = 8) is a 16550A
PPP generic driver version 2.4.2
NET: Registered protocol family 24
PPPoL2TP kernel driver, V0.17
PPTP driver version 0.8.4
pflash: found no supported devices
Creating 6 MTD partitions on "sflash":
0x00000000-0x00040000 : "pmon"
0x00040000-0x007e0000 : "linux"
0x00118400-0x00750000 : "rootfs"
0x00750000-0x007e0000 : "jffs2"
0x007f0000-0x00800000 : "nvram"
0x007e0000-0x007f0000 : "board_data"
u32 classifier
OLD policer on
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (512 buckets, 4096 max)
ip_tables: (C) 2000-2006 Netfilter Core Team
BCM fast NAT: INIT
NET: Registered protocol family 1
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 108k freed
Warning: unable to open an initial console.
et: module license 'unspecified' taints kernel.
PCI: Setting latency timer of device 0000:00:02.0 to 64
eth0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 5.10.56.46
PCI: Setting latency timer of device 0000:00:01.0 to 64
eth1: Broadcom BCM4329 802.11 Wireless Controller 5.10.56.46
net/ipv4/netfilter/tomato_ct.c [Jun 11 2010 00:35:35]
Algorithmics/MIPS FPU Emulator v1.5
nf_conntrack_rtsp v0.6.21 loading
nf_nat_rtsp v0.6.21 loading
JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
SCSI subsystem initialized
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
PCI: Setting latency timer of device 0000:00:04.1 to 64
ehci_hcd 0000:00:04.1: EHCI Host Controller
ehci_hcd 0000:00:04.1: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:04.1: irq 5, io mem 0x18004000
ehci_hcd 0000:00:04.1: USB 0.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
PCI: Setting latency timer of device 0000:00:04.0 to 64
ohci_hcd 0000:00:04.0: OHCI Host Controller
ohci_hcd 0000:00:04.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:04.0: irq 5, io mem 0x18009000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
usb 1-1: new high speed USB device using ehci_hcd and address 2
vlan1: add 01:00:5e:00:00:01 mcast address to master interface
usb 1-1: configuration #1 chosen from 1 choice
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 4 ports detected
vlan1: dev_set_promiscuity(master, 1)
device eth0 entered promiscuous mode
device vlan1 entered promiscuous mode
device eth1 entered promiscuous mode
br0: port 2(eth1) entering learning state
br0: port 1(vlan1) entering learning state
br0: topology change detected, propagating
br0: port 2(eth1) entering forwarding state
br0: topology change detected, propagating
br0: port 1(vlan1) entering forwarding state
vlan2: Setting MAC address to 00 26 f2 cd c2 0b.
vlan2: add 01:00:5e:00:00:01 mcast address to master interface
usb 1-1.2: new high speed USB device using ehci_hcd and address 3
usb 1-1.2: configuration #1 chosen from 1 choice
scsi0 : SCSI emulation for USB Mass Storage devices
usb 1-1.4: new full speed USB device using ehci_hcd and address 4
usb 1-1.4: configuration #1 chosen from 1 choice
scsi 0:0:0:0: Direct-Access Corsair VoyagerGT 1100 PQ: 0 ANSI: 0 CCS
sd 0:0:0:0: [sda] 8028160 512-byte hardware sectors (4110 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 43 00 00 00
sd 0:0:0:0: [sda] Assuming drive cache: write through
sd 0:0:0:0: [sda] 8028160 512-byte hardware sectors (4110 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 43 00 00 00
sd 0:0:0:0: [sda] Assuming drive cache: write through
sda: sda1
sd 0:0:0:0: [sda] Attached SCSI removable disk
usbcore: registered new interface driver usbserial
drivers/usb/serial/usb-serial.c: USB Serial support registered for generic
usbcore: registered new interface driver usbserial_generic
drivers/usb/serial/usb-serial.c: USB Serial Driver core
drivers/usb/serial/usb-serial.c: USB Serial support registered for FTDI USB Serial Device
ftdi_sio 1-1.4:1.0: FTDI USB Serial Device converter detected
drivers/usb/serial/ftdi_sio.c: Detected FT232BM
usb 1-1.4: FTDI USB Serial Device converter now attached to ttyUSB0
usbcore: registered new interface driver ftdi_sio
drivers/usb/serial/ftdi_sio.c: v1.4.3:USB FTDI Serial Converters Driver
tty: Unable to return correct speed data as your architecture needs updating.
root@tomato:/tmp/mnt/CARD/Beta16/newcs/bin#