Hey,
i'm using smartmontools 5.42 (from source) on Ubuntu 10.04 and i'm
trying to get more health informations about my devices which are
attached to a Hewlett-Packard Company Smart Array G6 controller.
My "problem" is that i am not getting all infos about the disk.
Command:
# smartctl --all --device=cciss,0 /dev/cciss/c0d0
Output:
smartctl 5.42 2011-10-20 r3458 [x86_64-linux-2.6.32-28-server] (local build)
Copyright (C) 2002-11 by Bruce Allen, http://smartmontools.sourceforge.net
User Capacity: 500.107.862.016 bytes [500 GB]
Logical block size: 512 bytes
Logical Unit id: 0x50014ee2afd33657
Serial number: WCASYF317894
Device type: disk
Local Time is: Tue Nov 22 14:31:14 2011 CET
Device supports SMART and is Enabled
Temperature Warning Disabled or Not Supported
SMART Health Status: OK
Current Drive Temperature: <not available>
Read defect list: asked for grown list but didn't get it
Error Counter logging not supported
Device does not support Self Test logging
Where is my mistake ... am i doing something wrong? I just want so see a
similar output like this from another machine:
smartctl 5.41 2011-06-09 r3365 [i686-linux-2.6.24-19-server] (local build)
Copyright (C) 2002-11 by Bruce Allen, http://smartmontools.sourceforge.net
=== START OF INFORMATION SECTION ===
Device Model: GB0160CAABV
Serial Number: 5RX6DFP2
Firmware Version: HPG1
User Capacity: 160.041.885.696 bytes [160 GB]
Sector Size: 512 bytes logical/physical
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: 7
ATA Standard is: ATA/ATAPI-7 T13 1532D revision 4a
Local Time is: Tue Nov 22 14:34:47 2011 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test
routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 433) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 54) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE
UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 100 253 006 Pre-fail
Always - 0
3 Spin_Up_Time 0x0002 098 097 000 Old_age
Always - 0
4 Start_Stop_Count 0x0033 100 100 020 Pre-fail
Always - 29
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail
Always - 0
7 Seek_Error_Rate 0x000f 079 060 030 Pre-fail
Always - 85927065
9 Power_On_Hours 0x0032 069 069 000 Old_age
Always - 27609
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail
Always - 0
12 Power_Cycle_Count 0x0033 100 100 020 Pre-fail
Always - 29
184 End-to-End_Error 0x0032 100 253 000 Old_age
Always - 0
187 Reported_Uncorrect 0x003a 100 100 051 Old_age
Always - 0
189 High_Fly_Writes 0x0022 100 100 000 Old_age
Always - 0
190 Airflow_Temperature_Cel 0x001a 069 058 000 Old_age
Always - 31 (Min/Max 29/39)
194 Temperature_Celsius 0x0000 031 042 000 Old_age
Offline - 31 (0 19 0 0)
195 Hardware_ECC_Recovered 0x0032 073 072 000 Old_age
Always - 153143868
197 Current_Pending_Sector 0x0000 100 100 000 Old_age
Offline - 0
198 Offline_Uncorrectable 0x0000 100 100 000 Old_age
Offline - 0
199 UDMA_CRC_Error_Count 0x0000 200 200 000 Old_age
Offline - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Thanks for your help
Greetings
Oliver
|