From: toni m. <ton...@ya...> - 2008-08-08 12:40:31
|
smartctl -d ata -a /dev/sdb smartctl version 5.38 [i686-pc-linux-gnu] Copyright (C) 2002-8 Bruce Allen Home page is http://smartmontools.sourceforge.net/ === START OF INFORMATION SECTION === Device Model: FUJITSU MHZ2250BS G2 Serial Number: K63QT87256FT Firmware Version: 00000109 User Capacity: 250,059,350,016 bytes Device is: Not in smartctl database [for details use: -P showall] ATA Version is: 8 ATA Standard is: ATA-8-ACS revision 3f Local Time is: Fri Aug 8 16:38:52 2008 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x80) Offline data collection activity was never started. Auto Offline Data Collection: Enabled. Self-test execution status: ( 249) Self-test routine in progress... 90% of test remaining. Total time to complete Offline data collection: (1009) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 143) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 100 100 046 Pre-fail Always - 19846 2 Throughput_Performance 0x0005 100 100 030 Pre-fail Offline - 44367872 3 Spin_Up_Time 0x0003 100 100 025 Pre-fail Always - 1 4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 7 5 Reallocated_Sector_Ct 0x0033 100 100 024 Pre-fail Always - 8589934592000 7 Seek_Error_Rate 0x000f 100 100 047 Pre-fail Always - 563 8 Seek_Time_Performance 0x0005 100 100 019 Pre-fail Offline - 0 9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 10 10 Spin_Retry_Count 0x0013 100 100 020 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 7 192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 4 193 Load_Cycle_Count 0x0032 100 100 000 Old_age Always - 50 194 Temperature_Celsius 0x0022 100 065 000 Old_age Always - 44 (Lifetime Min/Max 27/67) 195 Hardware_ECC_Recovered 0x001a 100 100 000 Old_age Always - 0 196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 446431232 197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x003e 200 253 000 Old_age Always - 0 200 Multi_Zone_Error_Rate 0x000f 100 100 060 Pre-fail Always - 22508 203 Run_Out_Cancel 0x0002 100 100 000 Old_age Always - 3728033513750 240 Head_Flying_Hours 0x003e 200 200 000 Old_age Always - 0 SMART Error Log Version: 1 No Errors Logged SMART Self-test log structure revision number 1 No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. __________________________________________________ Do You Yahoo!? Sie sind Spam leid? Yahoo! Mail verfügt über einen herausragenden Schutz gegen Massenmails. http://mail.yahoo.com |
From: toni m. <ton...@ya...> - 2008-08-11 07:15:04
|
# smartctl -d ata -a /dev/sdb smartctl version 5.38 [i686-pc-linux-gnu] Copyright (C) 2002-8 Bruce Allen Home page is http://smartmontools.sourceforge.net/ === START OF INFORMATION SECTION === Device Model: FUJITSU MHZ2250BS G2 Serial Number: K63QT87256FT Firmware Version: 00000109 User Capacity: 250,059,350,016 bytes Device is: Not in smartctl database [for details use: -P showall] ATA Version is: 8 ATA Standard is: ATA-8-ACS revision 3f Local Time is: Mon Aug 11 11:12:09 2008 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x80) Offline data collection activity was never started. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (1009) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off supp ort. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 143) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_ FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 100 100 046 Pre-fail Always - 155373 2 Throughput_Performance 0x0005 100 100 030 Pre-fail Offline - 44367872 3 Spin_Up_Time 0x0003 100 100 025 Pre-fail Always - 1 4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 8 5 Reallocated_Sector_Ct 0x0033 100 100 024 Pre-fail Always - 8589934592000 7 Seek_Error_Rate 0x000f 100 100 047 Pre-fail Always - 1339 8 Seek_Time_Performance 0x0005 100 100 019 Pre-fail Offline - 0 9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 13 10 Spin_Retry_Count 0x0013 100 100 020 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 8 192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 5 193 Load_Cycle_Count 0x0032 100 100 000 Old_age Always - 69 194 Temperature_Celsius 0x0022 100 065 000 Old_age Always - 40 (Lifetime Min/Max 27/67) 195 Hardware_ECC_Recovered 0x001a 100 100 000 Old_age Always - 2 196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 446431232 197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x003e 200 253 000 Old_age Always - 0 200 Multi_Zone_Error_Rate 0x000f 100 100 060 Pre-fail Always - 22515 203 Run_Out_Cancel 0x0002 100 100 000 Old_age Always - 3732317012361 240 Head_Flying_Hours 0x003e 200 200 000 Old_age Always - 0 SMART Error Log Version: 1 No Errors Logged SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA _of_first_error # 1 Short offline Completed without error 00% 13 - # 2 Short offline Completed without error 00% 10 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. __________________________________________________ Do You Yahoo!? Sie sind Spam leid? Yahoo! Mail verfügt über einen herausragenden Schutz gegen Massenmails. http://mail.yahoo.com |
From: Manfred S. <man...@gm...> - 2008-08-09 14:11:35
|
Hi Toni, thanks for sending in your drive details. However, your selftest was not finished when doing "smartctl -a". To check to correctness of the Attribute 9, we need a completed self test however. In your smartctl -a output, the test was only done to 90% percent. If the test is finished, you will see something like Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 173 - at the end of your smartctl -a output. Could you please do it again? - smartctl -t short /dev/sdb - wait until smartctl -a shows a new log entry - send your smartctl -a output Thanks, Manfred Am Freitag, den 08.08.2008, 12:40 +0000 schrieb toni muelhaupt: > smartctl -d ata -a /dev/sdb > smartctl version 5.38 [i686-pc-linux-gnu] Copyright (C) 2002-8 Bruce > Allen > Home page is http://smartmontools.sourceforge.net/ > === START OF INFORMATION SECTION === > Device Model: FUJITSU MHZ2250BS G2 > Serial Number: K63QT87256FT > Firmware Version: 00000109 > User Capacity: 250,059,350,016 bytes > Device is: Not in smartctl database [for details use: -P > showall] > ATA Version is: 8 > ATA Standard is: ATA-8-ACS revision 3f > Local Time is: Fri Aug 8 16:38:52 2008 CEST > SMART support is: Available - device has SMART capability. > SMART support is: Enabled > === START OF READ SMART DATA SECTION === > SMART overall-health self-assessment test result: PASSED > General SMART Values: > Offline data collection status: (0x80) Offline data collection > activity > was never started. > Auto Offline Data Collection: > Enabled. > Self-test execution status: ( 249) Self-test routine in > progress... > 90% of test remaining. > Total time to complete Offline > data collection: (1009) seconds. > Offline data collection > capabilities: (0x7b) SMART execute Offline > immediate. > Auto Offline data collection > on/off support. > Suspend Offline collection > upon new > command. > Offline surface scan > supported. > Self-test supported. > Conveyance Self-test > supported. > Selective Self-test supported. > SMART capabilities: (0x0003) Saves SMART data before > entering > power-saving mode. > Supports SMART auto save > timer. > Error logging capability: (0x01) Error logging supported. > General Purpose Logging > supported. > Short self-test routine > recommended polling time: ( 2) minutes. > Extended self-test routine > recommended polling time: ( 143) minutes. > Conveyance self-test routine > recommended polling time: ( 2) minutes. > SCT capabilities: (0x003d) SCT Status supported. > SCT Feature Control supported. > SCT Data Table supported. > SMART Attributes Data Structure revision number: 16 > Vendor Specific SMART Attributes with Thresholds: > ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE > UPDATED WHEN_FAILED RAW_VALUE > 1 Raw_Read_Error_Rate 0x000f 100 100 046 Pre-fail > Always - 19846 > 2 Throughput_Performance 0x0005 100 100 030 Pre-fail > Offline - 44367872 > 3 Spin_Up_Time 0x0003 100 100 025 Pre-fail > Always - 1 > 4 Start_Stop_Count 0x0032 100 100 000 Old_age > Always - 7 > 5 Reallocated_Sector_Ct 0x0033 100 100 024 Pre-fail > Always - 8589934592000 > 7 Seek_Error_Rate 0x000f 100 100 047 Pre-fail > Always - 563 > 8 Seek_Time_Performance 0x0005 100 100 019 Pre-fail > Offline - 0 > 9 Power_On_Hours 0x0032 100 100 000 Old_age > Always - 10 > 10 Spin_Retry_Count 0x0013 100 100 020 Pre-fail > Always - 0 > 12 Power_Cycle_Count 0x0032 100 100 000 Old_age > Always - 7 > 192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age > Always - 4 > 193 Load_Cycle_Count 0x0032 100 100 000 Old_age > Always - 50 > 194 Temperature_Celsius 0x0022 100 065 000 Old_age > Always - 44 (Lifetime Min/Max 27/67) > 195 Hardware_ECC_Recovered 0x001a 100 100 000 Old_age > Always - 0 > 196 Reallocated_Event_Count 0x0032 100 100 000 Old_age > Always - 446431232 > 197 Current_Pending_Sector 0x0012 100 100 000 Old_age > Always - 0 > 198 Offline_Uncorrectable 0x0010 100 100 000 Old_age > Offline - 0 > 199 UDMA_CRC_Error_Count 0x003e 200 253 000 Old_age > Always - 0 > 200 Multi_Zone_Error_Rate 0x000f 100 100 060 Pre-fail > Always - 22508 > 203 Run_Out_Cancel 0x0002 100 100 000 Old_age > Always - 3728033513750 > 240 Head_Flying_Hours 0x003e 200 200 000 Old_age > Always - 0 > SMART Error Log Version: 1 > No Errors Logged > SMART Self-test log structure revision number 1 > No self-tests have been logged. [To run self-tests, use: smartctl -t] > > SMART Selective self-test log data structure revision number 1 > SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS > 1 0 0 Not_testing > 2 0 0 Not_testing > 3 0 0 Not_testing > 4 0 0 Not_testing > 5 0 0 Not_testing > Selective self-test flags (0x0): > After scanning selected spans, do NOT read-scan remainder of disk. > If Selective self-test is pending on power-up, resume after 0 minute > delay. > > > __________________________________________________ > Do You Yahoo!? > Sie sind Spam leid? Yahoo! Mail verfügt über einen herausragenden > Schutz gegen Massenmails. > http://mail.yahoo.com > ------------------------------------------------------------------------- > This SF.Net email is sponsored by the Moblin Your Move Developer's challenge > Build the coolest Linux based applications with Moblin SDK & win great prizes > Grand prize is a trip for two to an Open Source event anywhere in the world > http://moblin-contest.org/redirect.php?banner_id=100&url=/ > _______________________________________________ Smartmontools-database mailing list Sma...@li... https://lists.sourceforge.net/lists/listinfo/smartmontools-database |