From: Hans-Peter J. <hp...@ur...> - 2004-03-03 18:41:14
|
Hi all, I would highly appreciate some comments. I have 4 of these and 4 SAMSUNG SP0802N, all with a similar Error. Doesn't look like I need to worry, but I would like to be safe. Is this behaviour to be expected. TIA, Pete smartctl version 5.27 Copyright (C) 2002-4 Bruce Allen Home page is http://smartmontools.sourceforge.net/ === START OF INFORMATION SECTION === Device Model: SAMSUNG SP1604N Serial Number: S013J10WB52289 Firmware Version: TM100-23 Device is: In smartctl database [for details use: -P show] ATA Version is: 7 ATA Standard is: ATA/ATAPI-7 T13 1532D revision 0 Local Time is: Wed Mar 3 16:05:10 2004 CET ==> WARNING: Contact developers at sma...@li...; may need -F samsung2 disabled SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x02) Offline data collection activity was completed without error. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (4320) seconds. Offline data collection capabilities: (0x1b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. No Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. No General Purpose Logging support. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 72) minutes. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000b 100 100 051 Pre-fail Always - 0 3 Spin_Up_Time 0x0007 064 064 000 Pre-fail Always - 6144 4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 9 5 Reallocated_Sector_Ct 0x0033 253 253 010 Pre-fail Always - 0 7 Seek_Error_Rate 0x000b 253 253 051 Pre-fail Always - 0 8 Seek_Time_Performance 0x0024 084 084 000 Old_age Offline - 12699 9 Power_On_Half_Minutes 0x0032 100 100 000 Old_age Always - 436h+46m 10 Spin_Retry_Count 0x0013 253 253 049 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 9 194 Temperature_Celsius 0x0022 184 157 000 Old_age Always - 18 195 Hardware_ECC_Recovered 0x000a 100 100 000 Old_age Always - 117734039 196 Reallocated_Event_Count 0x0012 253 253 000 Old_age Always - 0 197 Current_Pending_Sector 0x0033 253 253 010 Pre-fail Always - 0 198 Offline_Uncorrectable 0x0031 253 253 010 Pre-fail Offline - 0 199 UDMA_CRC_Error_Count 0x000a 100 100 000 Old_age Always - 0 200 Multi_Zone_Error_Rate 0x000b 100 100 051 Pre-fail Always - 0 201 Soft_Read_Error_Rate 0x000b 100 100 051 Pre-fail Always - 0 SMART Error Log Version: 1 ATA Error Count: 1 CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Timestamp = decimal seconds since the previous disk power-on. Note: timestamp "wraps" after 2^32 msec = 49.710 days. Error 1 occurred at disk power-on lifetime: 0 hours When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 04 51 00 01 00 00 a0 Error: ABRT Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Timestamp Command/Feature_Name -- -- -- -- -- -- -- -- --------- -------------------- b1 c0 00 01 00 00 a0 00 7.188 DEVICE CONFIGURATION RESTORE 80 00 01 01 00 00 a0 00 7.188 [VENDOR SPECIFIC] ec 00 03 01 00 00 a0 00 7.188 IDENTIFY DEVICE 91 00 3f 01 00 00 af 00 7.188 INITIALIZE DEVICE PARAMETERS [OBS-6] 10 00 00 01 00 00 a0 00 7.188 RECALIBRATE [OBS-4] SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 244 - # 2 Short offline Completed without error 00% 221 - # 3 Extended offline Completed without error 00% 202 - # 4 Short offline Completed without error 00% 199 - # 5 Short offline Completed without error 00% 177 - # 6 Short offline Completed without error 00% 154 - |