Menu
▾
▴
[smartmontools-support] Trouble using smartctl with LSI megaraid controller
|
From: <alo...@gm...> - 2017-02-11 20:48:37
|
Hello, I am able to run the commands below successfully on the command line but I am not able to get them to work in the /etc/smartd.conf file. CentOS 6.8 smartmontools.x86_64 1:5.43-1.el6 #from the shell Success! Results at end of email. smartctl -s on -d sat+megaraid,30 /dev/sda smartctl -a -d sat+megaraid,30 /dev/sda A few questions.... 1. Does anyone know the correct syntax to get it working in the smartd.conf file? 2. There are two partitions in this system /dev/sda and /dev/sdb. How do I know which drive Id (DID) belongs to which partition and does it matter if I assign a physical drive to the incorrect partition? 3. Is there a way to check all the drives on a single partition at once instead of having to check them individually with the sat+megaraid,N syntax? There are 20 physical drives on this system. 4. Once I enable smartctl on the command line for a drive is it on permanently or does it need to be enabled through the smartd.conf file? Thanks for the help! #smartd.conf file Failure! /dev/sda -H -d sat+megaraid,30 -s S/../../2/03 #/var/log/messages after restart of smartd service Feb 11 12:23:16 db011 smartd[3751]: Opened configuration file /etc/smartd.conf Feb 11 12:23:16 db011 smartd[3751]: Configuration file /etc/smartd.conf parsed. Feb 11 12:23:16 db011 smartd[3751]: Device: /dev/sda [megaraid_disk_30] [SAT], opened Feb 11 12:23:16 db011 smartd[3751]: Device: /dev/sda [megaraid_disk_30] [SAT], WDC WD2500BHTZ-04JCPV0, S/N:WD-WX11E23LZ256, WWN:5-0014ee-6ae7ef044, FW:04.06A00, 250 GB Feb 11 12:23:16 db011 smartd[3751]: Device: /dev/sda [megaraid_disk_30] [SAT], not found in smartd database. Feb 11 12:23:16 db011 smartd[3751]: Device: /dev/sda [megaraid_disk_30] [SAT], not capable of SMART Health Status check Feb 11 12:23:16 db011 smartd[3751]: Unable to register ATA device /dev/sda [megaraid_disk_30] [SAT] at line 28 of file /etc/smartd.conf Feb 11 12:23:16 db011 smartd[3751]: Device /dev/sda [megaraid_disk_30] [SAT] not available Feb 11 12:23:16 db011 smartd[3751]: Monitoring 0 ATA and 0 SCSI devices Feb 11 12:23:16 db011 smartd[3753]: smartd has fork()ed into background mode. New PID=3753. Drive list here. storcli64 /c0 /eall /sall show ------------------------------------------------------------------------------- EID:Slt DID State DG Size Intf Med SED PI SeSz Model Sp ------------------------------------------------------------------------------- 29:0 30 Onln 0 232.375 GB SATA HDD N N 512B WDC WD2500BHTZ-04JCPV0 U 29:1 31 Onln 0 232.375 GB SATA HDD N N 512B WDC WD2500BHTZ-04JCPV0 U 29:2 35 Onln 1 372.093 GB SATA SSD N N 512B SDLFGD7R-400G-1HA1 U 29:3 33 GHS - 372.093 GB SATA SSD N N 512B SDLFODAM-400G-1HA1 U 29:4 39 Onln 1 372.093 GB SATA SSD N N 512B SDLFGD7R-400G-1HA1 U 29:5 34 Onln 1 372.093 GB SATA SSD N N 512B SDLFGD7R-400G-1HA1 U 29:6 37 Onln 1 372.093 GB SATA SSD N N 512B SDLFGD7R-400G-1HA1 U 29:7 32 Onln 1 372.093 GB SATA SSD N N 512B SDLFODAM-400G-1HA1 U 29:8 42 Onln 1 372.093 GB SATA SSD N N 512B SDLFGD7R-400G-1HA1 U 29:9 38 Onln 1 372.093 GB SATA SSD N N 512B SDLFGD7R-400G-1HA1 U 29:10 36 Onln 1 372.093 GB SATA SSD N N 512B SDLFGD7R-400G-1HA1 U 29:11 41 Onln 1 372.093 GB SATA SSD N N 512B SDLFGD7R-400G-1HA1 U 29:12 45 Onln 1 372.093 GB SATA SSD N N 512B SDLFGD7R-400G-1HA1 U 29:13 43 Onln 1 372.093 GB SATA SSD N N 512B SDLFGD7R-400G-1HA1 U 29:14 40 Onln 1 372.093 GB SATA SSD N N 512B SDLFGD7R-400G-1HA1 U 29:15 44 Onln 1 372.093 GB SATA SSD N N 512B SDLFGD7R-400G-1HA1 U 29:16 47 Onln 1 372.093 GB SATA SSD N N 512B SDLFGD7R-400G-1HA1 U 29:17 48 Onln 1 372.093 GB SATA SSD N N 512B SDLFGD7R-400G-1HA1 U 29:18 49 GHS - 372.093 GB SATA SSD N N 512B SDLFGD7R-400G-1HA1 U 29:19 46 Onln 1 372.093 GB SATA SSD N N 512B SDLFGD7R-400G-1HA1 U ------------------------------------------------------------------------------- #Results of smartctl -a -d sat+megaraid,30 /dev/sda ===================================================================== smartctl 5.43 2012-06-30 r3573 [x86_64-linux-2.6.32-642.3.1.el6.x86_64] (local build) Copyright (C) 2002-12 by Bruce Allen, http://smartmontools.sourceforge.net === START OF INFORMATION SECTION === Device Model: WDC WD2500BHTZ-04JCPV0 Serial Number: WD-WX11E23LZ256 LU WWN Device Id: 5 0014ee 6ae7ef044 Firmware Version: 04.06A00 User Capacity: 250,059,350,016 bytes [250 GB] Sector Sizes: 512 bytes logical, 4096 bytes physical Device is: Not in smartctl database [for details use: -P showall] ATA Version is: 8 ATA Standard is: Exact ATA specification draft version not indicated Local Time is: Sat Feb 11 12:32:31 2017 PST SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED Warning: This result is based on an Attribute check. General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 2400) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 31) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x30bd) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 0 3 Spin_Up_Time 0x0027 177 177 021 Pre-fail Always - 2108 4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 17 5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0 7 Seek_Error_Rate 0x002e 100 253 000 Old_age Always - 0 9 Power_On_Hours 0x0032 071 071 000 Old_age Always - 21799 10 Spin_Retry_Count 0x0032 100 253 000 Old_age Always - 0 11 Calibration_Retry_Count 0x0032 100 253 000 Old_age Always - 0 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 17 192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 16 193 Load_Cycle_Count 0x0032 200 200 000 Old_age Always - 0 194 Temperature_Celsius 0x0022 119 107 000 Old_age Always - 28 196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0 197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0030 200 200 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0 200 Multi_Zone_Error_Rate 0x0008 200 200 000 Old_age Offline - 0 SMART Error Log Version: 1 No Errors Logged SMART Self-test log structure revision number 1 No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. #Results of smartctl -s on -d sat+megaraid,30 /dev/sda ====================================================================== smartctl 5.43 2012-06-30 r3573 [x86_64-linux-2.6.32-642.3.1.el6.x86_64] (local build) Copyright (C) 2002-12 by Bruce Allen, http://smartmontools.sourceforge.net === START OF ENABLE/DISABLE COMMANDS SECTION === SMART Enabled. |