Thread: [Serial-pci-info] kernel tells me to mail lspci output to this list
Brought to you by:
tytso
From: Cristian D. <cri...@ws...> - 2002-11-10 17:39:26
|
Hi all, Here is goes (dmesg): --------------------------------- Redundant entry in serial pci_table. Please send the output of lspci -vv, this message (10b9,5457,103c,0025) and the manufacturer and name of serial board or modem board to ser...@li.... --------------------------------- The box is a HP Omnibook XE4500 laptop(product no F4873H). The lspci dump follows: -------------------------------------------------- [root@bluefish diciu]# /sbin/lspci -vv 00:00.0 Host bridge: Acer Laboratories Inc. [ALi] M1671 Northbridge [Aladdin-P4] (rev 02) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR+ Latency: 0 Region 0: Memory at f0000000 (32-bit, prefetchable) [size=128M] Capabilities: [b0] AGP version 2.0 Status: RQ=27 SBA+ 64bit- FW+ Rate=x1,x2,x4 Command: RQ=0 SBA+ AGP+ 64bit- FW- Rate=x1 Capabilities: [a4] Power Management version 1 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00:01.0 PCI bridge: Acer Laboratories Inc. [ALi] PCI to AGP Controller (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 I/O behind bridge: 00009000-00009fff Memory behind bridge: e0100000-e01fffff Prefetchable memory behind bridge: e8000000-efffffff BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B- 00:02.0 USB Controller: Acer Laboratories Inc. [ALi] USB 1.1 Controller (rev 03) (prog-if 10 [OHCI]) Subsystem: Hewlett-Packard Company: Unknown device 0025 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 (20000ns max), cache line size 08 Interrupt: pin A routed to IRQ 10 Region 0: Memory at e0000000 (32-bit, non-prefetchable) [size=4K] Capabilities: [60] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00:06.0 Multimedia audio controller: Acer Laboratories Inc. [ALi] M5451 PCI AC-Link Controller Audio Device (rev 02) Subsystem: Hewlett-Packard Company: Unknown device 0025 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR+ <PERR+ Latency: 64 (500ns min, 6000ns max) Interrupt: pin A routed to IRQ 5 Region 0: I/O ports at 1000 [size=256] Region 1: Memory at e0001000 (32-bit, non-prefetchable) [size=4K] Capabilities: [dc] Power Management version 2 Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00:07.0 ISA bridge: Acer Laboratories Inc. [ALi] M1533 PCI to ISA Bridge [Aladdin IV] Subsystem: Acer Laboratories Inc. [ALi] ALI M1533 Aladdin IV ISA Bridge Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Capabilities: [a0] Power Management version 1 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00:08.0 Modem: Acer Laboratories Inc. [ALi] M5457 AC-Link Modem Interface Controller (prog-if 00 [Generic]) Subsystem: Hewlett-Packard Company: Unknown device 0025 Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Interrupt: pin A routed to IRQ 10 Region 0: Memory at e0002000 (32-bit, non-prefetchable) [size=4K] Region 1: I/O ports at 1400 [size=256] Capabilities: [40] Power Management version 2 Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00:0a.0 CardBus bridge: Texas Instruments PCI1250 PC card Cardbus Controller (rev 01) Subsystem: Hewlett-Packard Company: Unknown device 0025 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 168, cache line size 08 Interrupt: pin A routed to IRQ 5 Region 0: Memory at 18000000 (32-bit, non-prefetchable) [size=4K] Bus: primary=00, secondary=02, subordinate=02, sec-latency=176 Memory window 0: 18400000-187ff000 (prefetchable) Memory window 1: 18800000-18bff000 I/O window 0: 00004000-000040ff I/O window 1: 00004400-000044ff BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+ 16-bit legacy interface ports at 0001 00:0a.1 CardBus bridge: Texas Instruments PCI1250 PC card Cardbus Controller (rev 01) Subsystem: Hewlett-Packard Company: Unknown device 0025 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 168, cache line size 08 Interrupt: pin A routed to IRQ 5 Region 0: Memory at 18001000 (32-bit, non-prefetchable) [size=4K] Bus: primary=00, secondary=03, subordinate=03, sec-latency=176 Memory window 0: 18c00000-18fff000 (prefetchable) Memory window 1: 19000000-193ff000 I/O window 0: 00004800-000048ff I/O window 1: 00004c00-00004cff BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+ 16-bit legacy interface ports at 0001 00:0c.0 FireWire (IEEE 1394): Texas Instruments TSB43AB21 IEEE-1394a-2000 Controller (PHY/Link) (prog-if 10 [OHCI]) Subsystem: Hewlett-Packard Company: Unknown device 0025 Control: I/O- Mem- BusMaster- SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Interrupt: pin A routed to IRQ 0 Region 0: Memory at e0003000 (32-bit, non-prefetchable) [disabled] [size=2K] Region 1: Memory at e0004000 (32-bit, non-prefetchable) [disabled] [size=16K] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00:10.0 IDE interface: Acer Laboratories Inc. [ALi] M5229 IDE (rev c4) (prog-if b0) Subsystem: Hewlett-Packard Company: Unknown device 0025 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 (500ns min, 1000ns max) Interrupt: pin A routed to IRQ 0 Region 0: [virtual] I/O ports at 01f0 Region 1: [virtual] I/O ports at 03f4 Region 2: [virtual] I/O ports at 0170 Region 3: [virtual] I/O ports at 0374 Region 4: I/O ports at 1800 [size=16] Capabilities: [60] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00:11.0 Bridge: Acer Laboratories Inc. [ALi] M7101 PMU Subsystem: Hewlett-Packard Company: Unknown device 0025 Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- 00:12.0 Ethernet controller: National Semiconductor Corporation DP83815 (MacPhyter) Ethernet Controller Subsystem: Unknown device 3c08:a400 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 90 (2750ns min, 13000ns max) Interrupt: pin A routed to IRQ 11 Region 0: I/O ports at 1c00 [size=256] Region 1: Memory at e0008000 (32-bit, non-prefetchable) [size=4K] Expansion ROM at <unassigned> [disabled] [size=64K] Capabilities: [40] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=320mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME+ 01:00.0 VGA compatible controller: ATI Technologies Inc Radeon Mobility M6 LY (prog-if 00 [VGA]) Subsystem: Hewlett-Packard Company: Unknown device 0025 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B+ Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 66 (2000ns min), cache line size 08 Interrupt: pin A routed to IRQ 9 Region 0: Memory at e8000000 (32-bit, prefetchable) [size=128M] Region 1: I/O ports at 9000 [size=256] Region 2: Memory at e0100000 (32-bit, non-prefetchable) [size=64K] Expansion ROM at <unassigned> [disabled] [size=128K] Capabilities: [58] AGP version 2.0 Status: RQ=47 SBA+ 64bit- FW- Rate=x1,x2,x4 Command: RQ=27 SBA+ AGP+ 64bit- FW- Rate=x1 Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- ---------------------------------------------------------------- Sorry about the lengthy message, let me know (via reply, I'm not subscribed to the list) if there is anything else you need. Cheers, Cristi |